Silverado :: 2003 - Intermittent CEL Code P0304 / Misfire On Cylinder 4
My 2003 Silverado 5.3 has an intermittent CEL. I plugged in the reader and found code P0304, misfire #4 cylinder. I changed the coil, swapped the spark plug and wire from #2 cylinder to see if the code would follow. Nope, didn't follow. I swapped the injector also, same results. My daughter decided to borrow the truck and drove it so low on fuel that the low fuel light came on in the drive way. I added about 4 gallons of fuel and now the light went off. I started the engine after a jump start, and the engine really runs rough and now won't stay running. I am thinking that the fuel filter is probably needing changed because of how low the fuel.
I haven't checked the fuel pressure yet and will do that today. Now, what really puzzles me is the intermittent part. Sometimes it will run with no problem, but then the CEL will come on and the fun begins. The Chevrolet dealer says it's caused by the valves turning in the head and when it reaches a certain spot, it detects the misfiring #4 cylinder resulting in the CEL. If I pull in the driveway with the engine missing, go back out in a short time, start the engine and it runs fine. Same thing if it's running fine and I can start it and the CEL blinks and it begins missing, but may stop and run fine. I am stumped and not so sure about the turning valves.
Accent LC (2000-05) :: CEL Flashing / PO301 Code - Misfire In Cylinder 1
I got a 2002 and its giving ma a po301. I know that means a misfire in cylinder 1. I replaced the Coils, Plugs and wires, and now its still there but the check engine light is flashing. What next?????
View 2 RepliesGrand AM :: 2000 GT 3.4 Keeps Throwing Code P304 - Cylinder 4 Misfire At Idle
2000 Grand Am GT with 3.4 and 150,000 miles. Car keeps throwing code P304 - cylinder 4 misfire. The main issue is the light and needing to pass emissions test. It has just recently had new plugs, wires, and injector #4.
The fuel pressure regulator was replaced about 3 years ago because it was leaking fuel, enough to smell while driving the car with windows rolled down. Shortly after the fpr was replaced, the acceleration problem seems to have started, either by coincidence, or improper installation. The light/error has been occurring for quite some time, about the past year or two. About a year ago, the car was also throwing a random misfire code. I am not positive if both codes were being thrown at the same time, and when exactly the P304 started.
The crank (or cam) sensor was replaced and worked with the issue for a short while (removed codes/light for maybe a few months?) Before the sensor was replaced, the car would stumble at very slow speeds, 0-10 mph. Also replaced Idle Air Control valve last year. The car would sometimes surge on semi warm starts (not cold, not 190-200) between 500-1000 rpms. The surge would be worse when I had the blower running or the rear defrost on, down to 200 rpms at times.
Currently, the car runs perfectly fine for me, except when trying to accelerate on highway ramps. Its firing somewhat when you step on the pedal, but lags and takes longer than normal to accelerate up to speed for merging with traffic. Drove the car after new injection and said it runs fine while driving, but the misfire seems to be mostly or only occurring at idle.
Golf IV / Jetta IV :: 2000 - Cylinder 2 Misfire / Pending Code P0302
2000 Jetta 2.0 cylinder 2 misfire. Replaced plugs and wires. No check engine light but code is pending and there's still a misfire. Need to smog
Replace coil pack?
Swap fuel injectors and recheck?
Ford Excursion :: 2000 V10 - Rough Idle - P0304 Code / Cylinder 4 Misfire
I recently bought a 00 Excursion v10 2wd everything looked right no major problems. I noticed it has a rough idle and i thought it could be the EGR i went under the hood and there's no EGR in sight. I plugged the OBD reader to see if it would give any codes since the there was no check engine light on and wanted wanted to make sure it worked, It showed a P0304 code its Cyl4 misfire i checked plugs/coils and i noticed there's a little insert inside Cyl4 plugs hole in the head that it has the plug screwed on. I decided to change all the plugs and the coils and i still have the rough idle and code i can hear a ticking noise around the engine in the passenger side.
View 7 RepliesTacoma :: 2000 V6 Check Engine Light Code P300 / P306 - Cylinder 3 And 6 Misfire
2000 Tacoma v6 has has always ran good, but has check engine light code P300 & P306. cly 3 & cly 6 missfire, lean bank 1. Vacuum test showed no problems.
I've changed plugs & wires, switched coils around cleaned mass air flow sensor, checked timing. Ran Seafoam through intake, and gas tank. Check engine light went out for about three miles, then came back on. What else can I do to keep that blinking check engine light off?
Ford Ranger / B-Series :: 2000 - Running Rough And Code For Misfire On Cylinder 3 / 2nd Coil Pack
2000 4.2....Last year I had to replace the coil pack when it started running rough and had a code for a misfire on cylinder 3. It is doing the exact same thing now, same code, same cylinder. Is there something wrong that is causing this?
View 5 RepliesSilverado :: 2003 With Code P0307 Misfire / CEL Flashing
I'm having an issue with my 2003 Silverado, current engine is LS1 from a WS6 Trans Am, mostly stock, stainless headers, no cats, stall converter. I replaced fuel pump a few weeks ago and last week i took a road trip and when I hit the interstate the CEL started flashing. I pulled over and used my scanner and saw that it was P0307. I cleared code and continued on. The only noticeable problem was that it was not shifting into overdrive. After a while the light quit flashing and eventually it shifted into OD.
This happened several more times on a 750 mile trip. I had a mechanic friend check it over and he couldn't find anything, wasn't throwing codes at that time. He check sparked plug, swapped the coil to #5 and still had the issue. Didn't get a chance to check the fuel injector. The trip home it did the same thing. IF it were indeed a bad injector, wouldn't the problem be ongoing instead of coming and going? Took to local chevy dealer thinking they could diagnose it but since it didn't throw a code they couldn't find anything.
Passat (B5) :: Car Has Misfire And Code On The Cylinder
I am having a misfire code on the #1 cylinder. Its not bad but I really want to nip it in the butt before it goes out completely. I was told to try and get some of the older style coilpacks that bolt on and go with them. Can I put them on my 03 passat 1.8t.
View 2 RepliesNissan :: 1989 - Cylinder Misfire CEL Code
1989 Nissan pathfinder. 6cylinder - VG30i - Manual trans - Throttle body injected. No CEL.
I've been trying to diagnose a misfire on my 89 Pathfinder during my lunch breaks. I just changed out the the plugs, dist. cap, dist. rotor and wires. Still misfiring.
When it starts-up the misfire "putt" is random, but once the idle lowers to about 1k it gets very rhythmic and just sounds like part of the idle and the car vibrates a little too much. Stinky exhaust (obviously) but no blue smoke or anything.
Finally bringing the car home to do some diagnosis over the weekend. Next I'm going to do some cylinder compression checks and vacuum checks. Probably check fuel pressure too. Is it odd that I'm not getting a cylinder misfire CEL code? The manual lists the code type.
Golf IV R32 :: PO302 Code - Misfire On Cylinder 2
PO302 CODE . Lets hope that it's only cylinder 2 coil or spark plug !
View 18 RepliesIntrepid :: 2001 SE - Misfire In Cylinder 4 (Code P0304)
Have '01 SE. yesterday I got a misfire in cylinder 4 (code P0304) the service light blinked on and off 3 to 4 times than stayed solid. changed plugs and boots about 1 to 2 months ago, didn't change coils and they r not in the best shape but didn't have money to replace at time. So I replaced the coil for #4 and it still runs rough with code, plug has some ware but looks fine.
View 1 RepliesS-10 :: 98 Chevy ODB Error Code P0304 / Cylinder 4 Misfire
I left my chevy s-10 truck sitting over the christmas (23/24/25) and it was really cold outside and when i got back i started getting a P0304 (Cylinder 4 Misfire). I replaced the spark plugs and spark plug wires. May be the cold would cause this to happen? I think I've noticed the trucks fuels efficiency drop over the past month). May be the fuel injector(s)? Is the s-10 TBI or does it have fuel injectors for each cylinder?
View 8 RepliesGolf IV / Jetta IV :: Code P0304 On Mk4 2.0 AEG - Misfire On Cylinder 4
2000 Jetta GL 2.0 AEG. I am receiving the P0304 which I have identified as Cylinder misfire #4. I read on some previous posts that I cannot be the distributor because if it was I would be receiving misfires on two cylinders. The spark plugs are OEM NGK and have been replaced recently.
View 2 RepliesPrius (2004-09) :: Intermittent Misfire Cylinder 1 Code
I posted this problem several months ago about a p301 code that my 2007 Prius has been generating. I eliminated all the easy stuff... plug, spark unit, fuel injector. Over the past year since I've had the car, the CEL light has gone on for a couple months then shut itself off for a couple, then back on ... probably has shut itself off 3 times in the past year, each time staying off about a month or two before coming back on. Some background on the car, supposedly the PO hit a rock and damaged the motor about 2 years ago and had the short block replaced.
Anyway, the CEL has been on again for about a month, and I got a notice for Illinois emission testing, so I decided to take it in to the dealer and have him do a diagnostic so I can get the emissions passed. After an hour and a half of testing they told me that the best they could ascertain, the car has been submerged in water, as there is a lot of rust in areas that never get any rust, and they think there's a short somewhere.
The service manager at the dealership said if it was his car he wouldn't spend the money for another 5 hours of trouble shooting, and if the car runs good he'd just drive it as is. They cleared the CEL and the service manager just charged me for an oil change as they caught a recall on the steering that hadn't been done and figured he'd let me slide on the hundred for the diagnostic.
Golf IV / Jetta IV :: Cylinder 2 And 3 Misfire - Code P0411
Alright so my car is popping up 4 codes.
P0411 - Secondary Air Injection System Incorrect Flow Detected
P0300 - Random/Multiple Cylinder Misfire Detected
P0302 - Cylinder 2 Misfire Detected
P0303 - Cylinder 3 Misfire Detected
Vehicle: 1999.5 VW Jetta MK4 2.0L GLS (AEG)
The P0411 code I have had for a while now and I been lacking to fix it. I pretty sure I can get this fixed but it doesn't cause problems so I haven't paid to much attention to it. Anyways, the other day I noticed a puddle of coolant under my car so after checking it out, the water pump was leaking so I bought a new one and replaced the old one. However, during the replacement process I had to remove the timing belt and I accidentally turned the top pulley about 1 notch and didn't notice at the time. After putting everything back on, I turned my car on and the engine sound a bit weak so I ran for about 10 minutes around a couple blocks.
I instantly noticed that the car had no power and it took me a long time to speed up. When I got back, I plugged in my scanner and I only had the same P0411 code and nothing else. After carefully reviewing the camera I had recording during the water pump replacement, I notice I had turned the top pulley a bit so I went ahead and removed the timing belt, readjusted it, and it worked! I was excited that the car was working fine again. Soon after, I headed out to take a drive and noticed after 60MPH the car didn't have much power. The car still accelerates after 60MPH, but extremely slow. As soon as I arrived back home, I plugged in my scanner and that is where I seen the 4 codes. Now my question is what could have caused this? Could I have damaged something when I ran my car with the incorrect timing?
Things I have done so far:
-I checked to see if I left anything unplugged.
-I checked for any vacuum leaks
-I checked my oxygen sensors so see if I was running rich/lean
Things I will do after work today:
-Check the spark plugs
-Check spark plug cable for damage
Golf IV / Jetta IV :: 2001 1.8T - Cylinder Misfire Code
I recently changed my spark plugs + coil packs in my 01 1.8T because it read a couple cylinder misfire codes. Drove it for a few days out of curiosity plugged the code reader in again and it's still reading misfire codes. What could the issue be still?
View 6 RepliesGolf IV R32 :: Odd Code Combo - P2181 And Cylinder 2 Misfire
Started happening recently where I can't bring her past 5k without misfiring on cyl 2 and throwing the p2181 code. I changed the coil just to be sure, but I do know my coolant sensor wires were a little snug from the TB being so close.
View 1 RepliesNissan - Sentra :: Code P0303 - Cylinder 3 Misfire
It keeps reading the code P0303 "cylinder 3 misfire". All coil packs, fuel injectors, spark plugs have been replaced. The exhuast smells normal. The oil is the correct color(maple syrup color, NOT milky). It's not blowing through coolant. Compression test came back normal. It's not the cat converter because the exhaust doesn't smell like rotten eggs. The car is sometimes hard to start. it hesitates/stumbles and shakes really bad. It feels like its not getting enough power.
View 10 Replies