Golf IV / Jetta IV :: Pulled Over Code P0302 For Misfire
I have a 2005 Jetta 2.0 BEV GLS. I got a code P0302 for misfire on cylinder 2. I am pretty sure it's the Ignition coil. I live in Canada and my autoparts store only has BWD brand. I have read this is a crappy brand.
View 1 RepliesGolf IV / Jetta IV :: 2000 GLX - Intermittent Start And Stall / Pending Code P0321
My wife drove the car to work, and it ran good. She got a check engine light, but it was not on when I got home from work. I started the car and it idled fine for a couple of minutes and then it stalled. I check the codes and there was nothing locked in. There was a pending coding P0321. I am not sure what a pending code is, but I assume not enough to trigger the check engine light.
After work each night this week I tried troubleshooting but I have not gotten anything accomplished. Each night the car would start fine but if I turned it off it would not start until many tries if at all. It turns over strong but won't start. I drove it around the neighborhood today and it stalled and wouldn't restart.
The fuel pump primes. When the car won't start the fuel pump relay clicks constantly. Is this normal? I replaced the fuel filter because it has been 50k miles. Is the crank shaft sensor the problem? I hate to throw money at parts that aren't the problem when I can't get a code to trip the check engine light.
Santa FE SM (2001-06) :: Code P0302 Misfire In Cylinder 2
I just purchased a 2005 Santa Fe, 4WD, 2.7l..the engine has a miss...the code that came up was "misfire in #2 cylinder"..I checked the coil pack...and the wire harness just crumbled..so I replaced the coil pack...reset the code..and it was good for a couple of days...I got through inspection...today I put on the A/C..and the engine got rough..the check engine light came back on..same code..misfire in #2..I'm thinking the injector or what else could it be? plug? wire?
View 3 RepliesAccent MC (2006-11) :: 2010 GL - Misfire On Cylinder 2 / Code P0302
I have a 2010 accent GL manual sedan. It has 104,962 KM on it, the warranty expired December 18, 2015. Since February this car has become a frustrating money pit. Being in the dealership constantly for repairs, then within a week something else 'happens' and back it goes. Spent almost $5000 in 4 months on repairs. Decided that's enough and will do majority of repairs myself.
Yesterday while drive on the highway I had a sudden loss of power and a check engine light came on. My scanner which has become a standard item in my glove box indicated a misfire on cylinder 2 - P0302. I limped the car home, in 3rd gear I was having a hard time staying above 2000rpm at 60km/h. at lights I had to use hand brake so I could keep my foot on accelerator, revs were dropping below 300.
Today I replaced all the plugs (all 4 were still in good or better condition, #2 showed signs of a slightly rich burn and #3 a slightly lean burn), replaced all coil boots (no cracks, no burns, and still pliable), removed and cleaned all the injectors. Error code P0302 persists.
Santa FE SM (2001-06) :: 2002 - Code P0302 / Misfire On Cylinder 2
I have a 2002 Santa Fe 4 cyl that is giving me a problem that I could use some advice on tracking down & fixing . First & most important is a code P0302 # 2 Cyl misfire. How to check the ignition coil pack , injector ,& wire for this cylinder in home garage with normal tools & meter . Is there a you tube displaying how to do this step by step ?
The other problem which I don't have the code for at this time is that some part of the exhaust is not getting warm enough & this also put's the check engine light on . Will get back on this one when I solve the main problem Misfire.
Santa FE SM (2001-06) :: Engine Light Come On With Code P0302 Cylinder 2 Misfire
I have a 2005 Santa Fe with the 3.5 with 112000 miles on it. I had the engine light come on with the code P0302 cyl #2 misfire, I got spark plugs, plug wires to do a tune up on it. I changed all of it and got it back together, started it up and it still had a miss to it. I then took the front spark plugs out and did a compression test on it. #2 was at 85, #4 was at 120, and #6 was at 160. I couldn't check the back cyls because I had already put the intake back on. I then did a wet test, and all the cyls came up to 160. So this tell me that the piston rings are bad in #2 and going bad in #4. I have kept all the oil changes up and up to this point I haven't had any trouble with it. Having this problem with there 3.5?
View 1 RepliesPassat (B6) :: Error Code P0302 / Misfire In Cylinder 2 - Oil On Spark Plug
Getting error code p0302, misfire in 2, pulled the plug and had oil on the treads and on the lower part. My guess is the valve cover gasket, but I'm not 100 percent sure.
View 18 RepliesSanta FE SM (2001-06) :: Engine Having Hiccups When Accelerating - Code P0302 / Misfire On Cylinder 2
2005 3.5L FWD. 5 days ago I left the house, the engine was running smooth at idle but having hiccups when accelerating. Check engine light went on when accelerating but going off at idle. Turned around at the first stop light, parked the car home and pulled code P0302 misfire on #2 . Figured it's most likely the coil, was going to order one next day but to my surprise, no more check engine light next day and engine has been running smooth since then. Probably drove 100 miles since with no issues. I have 6 spark plugs waiting to be replaced but it's too cold to do it right now unless it's an emergency. Car has 105k miles now, spark plugs were changed at 63k. Was this just a fluke and P0302 will probably not come back or should I not risk it and just go ahead and replace the coil? If I end up replacing the coil, should I do one coil or all three?
View 22 RepliesFord Ranger / B-Series :: 1995 - Misfire In Cylinder 2 / CEL Flashing And Code P0302
I have a 1995 ford ranger 2.3 L dual coil packs new plugs, wires, coil packs, tps, idle air sensor, internal temp sensor, and a replaced mass air flow sensor from wrecker. That all said my one son missed a plug when i replaced it , it had no tip left on it , but since then i now have a misfire in cylinder 2 where the olther plug was found and replaced ...
Gap for plugs are .44
Used the wrecker maf to see if it would clear a p0113 which it did. I am stumped on why at approx. 30 minutes of driving that the cel will flash then set a p0302, no other codes no fuel smell. rechecked plugs all are clean haven't been able to check fuel pressure yet, and i out a can of seafoam in the tank to see if it clear out injectors.
Besides all, I will check injector to see if I hear anything but I'm stumped. Also we have to have an emission test so is it best to fail the test and will it show me what I'm missing.
Golf IV / Jetta IV :: Code P0304 On Mk4 2.0 AEG - Misfire On Cylinder 4
2000 Jetta GL 2.0 AEG. I am receiving the P0304 which I have identified as Cylinder misfire #4. I read on some previous posts that I cannot be the distributor because if it was I would be receiving misfires on two cylinders. The spark plugs are OEM NGK and have been replaced recently.
View 2 RepliesGolf IV / Jetta IV :: Cylinder 2 And 3 Misfire - Code P0411
Alright so my car is popping up 4 codes.
P0411 - Secondary Air Injection System Incorrect Flow Detected
P0300 - Random/Multiple Cylinder Misfire Detected
P0302 - Cylinder 2 Misfire Detected
P0303 - Cylinder 3 Misfire Detected
Vehicle: 1999.5 VW Jetta MK4 2.0L GLS (AEG)
The P0411 code I have had for a while now and I been lacking to fix it. I pretty sure I can get this fixed but it doesn't cause problems so I haven't paid to much attention to it. Anyways, the other day I noticed a puddle of coolant under my car so after checking it out, the water pump was leaking so I bought a new one and replaced the old one. However, during the replacement process I had to remove the timing belt and I accidentally turned the top pulley about 1 notch and didn't notice at the time. After putting everything back on, I turned my car on and the engine sound a bit weak so I ran for about 10 minutes around a couple blocks.
I instantly noticed that the car had no power and it took me a long time to speed up. When I got back, I plugged in my scanner and I only had the same P0411 code and nothing else. After carefully reviewing the camera I had recording during the water pump replacement, I notice I had turned the top pulley a bit so I went ahead and removed the timing belt, readjusted it, and it worked! I was excited that the car was working fine again. Soon after, I headed out to take a drive and noticed after 60MPH the car didn't have much power. The car still accelerates after 60MPH, but extremely slow. As soon as I arrived back home, I plugged in my scanner and that is where I seen the 4 codes. Now my question is what could have caused this? Could I have damaged something when I ran my car with the incorrect timing?
Things I have done so far:
-I checked to see if I left anything unplugged.
-I checked for any vacuum leaks
-I checked my oxygen sensors so see if I was running rich/lean
Things I will do after work today:
-Check the spark plugs
-Check spark plug cable for damage
Golf IV / Jetta IV :: 2001 1.8T - Cylinder Misfire Code
I recently changed my spark plugs + coil packs in my 01 1.8T because it read a couple cylinder misfire codes. Drove it for a few days out of curiosity plugged the code reader in again and it's still reading misfire codes. What could the issue be still?
View 6 RepliesGolf IV / Jetta IV :: 2000 VR6 Random Misfire In Cylinder 2 And 5
About a month ago my wife's 2000 Jetta with the VR6 engine in it started acting up and throwing codes. The codes it threw were for random misfire, misfire in cylinder 2, and misfire in cylinder 5. Starting out, we changed spark plugs, fuel filter, and made sure the injectors were clean.
The problem didn't go away so we water tested the coil and wires, but they passed that test. The wires were quite old and out of spec, while the coil was in-spec across all terminals, according to the vehicle service manual, so we installed some new OEM leads this weekend. While installing the leads we noticed a disconnected vacuum line and reconnected that as well.
The vehicle was driving great for two and a half days, then today while I was sitting at a stop light, it started missing really badly and felt like it was going to kill. It did this for about 5 seconds, then recovered and ran smooth for about 5 seconds, before getting really rough until I started driving when the light changed. It didn't do it when I drove it a few hours later at all. This episode didn't throw any codes either.
What could be causing this issue? Would the MAF cause the intermittent missing, or is it possible that the computer is going bad?
Golf IV / Jetta IV :: Catalytic Code / Cylinder 3 Misfire P0303
I own a BMW not a VW! My 19yr old daughter purchased her first car a few months ago, an '03 Jetta 2.0L with approx. 170,xxx miles. Just after she got it we pulled a P0420 code, but it ran fine so we haven't worried too much about it. I've cleared that code and after about 2 weeks it will come back. Last week it started to have some issues with rough idle, stumbling/hesitation. I pulled the codes yesterday an in addition to the catalytic code is a cylinder #3 misfire P0303. I thinking the 2 codes are not related. I'm assuming the typical things to look for on the misfire are coil, wire, plug? Looks like the coil on this engine is a combined unit so no switching coil packs to see if the miss follows a bad coil pack.
View 4 RepliesGolf IV / Jetta IV :: CEL On With Camshaft Position Sensor Code And Misfire On Cylinder 3
She is a 1999.5 Golf 2.0 (although, she just has a rabbit symbol on the hatch, is she a Rabbit or did someone remove the Golf badge?) I just bought the car, with less than 160,000 miles. The dome lights work sometimes, Door Ding works intermittently as well, but sometimes will "glitch" in other words it will be making the sound but it kind of stutters? Odd? The horn sometimes works, however it is very silent? Check engine light is on with a camshaft position sensor code and miss on cylinder 3. Someone told me to replace the "109 relay"... could this be the problem or is this the CCM?
View 5 RepliesGolf IV / Jetta IV :: Loss Of Power And Hesitation / CEL Code For Misfire On Cylinder 1 And 5
When i got my 2000 jetta vr6 it has a CEL for misfires. Searched this board and google already. Im thinking injectors (havent checked yet) I noticed something weird the other day. At a light i get the CEL flashing. Then after a bit it will come on and stay on. I plugged in my generic reader and deleted the codes. When the CEL is on I get loss of power and hesitation. When its deleted the car runs better. I get my power back. I looked in the coolant tank and see no bubbles. Could this be the ECM? Im still going to get injectors but want to buy the gasket and anything else I am going to need to put it back together. I already cleaned the MAF, replaced some vac lines, coil pack, wires and checked plugs (gapped at .28) ...
View 4 RepliesGolf IV / Jetta IV :: 2000 - Cylinder 2 Misfire And Engine Sputter
2000 GTI GLS 2.0L ... I understand I need to replace the Ignition Coil Pack on my car. I have looked on ECS Tuning to find the coil pack, but from all the pictures I see of other people coil packs they look nothing like what mine do. So I'm wondering if they are different for my specific car? So the issue that I have is my engine sputters sometimes, but more so when is wet outside. Its only cylinder 2 misfiring currently, and I replaced my Fuel Filter and Fuel Pump already in the past 4 or 5 months. Also a local shop had done some work recently and I know they had replaced the spark plugs. So I'm just wondering what coil packs I need for my car, and how I would go about replacing them. From what I saw online with other 2.0L (They weren't GTIs tho) was that the coild pack was behind the SIA pump or something like that, and they are a small black box. It looks to me that my coil packs are inline above the spark plugs and cylinders?
View 2 RepliesCamry :: 2002 - P0302 Cylinder 2 Misfire Warning
I have a 2002 Camry, 2.4 with 155k miles.
This morning I was going to work and was making a lane change and hit the accelerator quite aggressively. Suddenly my engine started to run really rough and shook the car and the check engine light started flashing.
I checked the engine code and its giving me a P0302 Cylinder 2 Misfire warning.
I have read that there can be various reasons but I figured since this problem is consistent its not a vacuum issue? Could it just be a bad plug? I don't have the tools to fix it, I am going to get them soon to pull the plugs and inspect then, and will replace them anyway since I don't think they have ever been replaced.
Lexus GS 2006-11 :: Check Engine P0302 - Misfire On Cylinder 2
Check engine code (P0302). I have a 2007 GS 350 with 116k miles that was driving perfect until this week. My check engine light was initially blinking but is now on solid along with the check VSC light. My question is: of the 6 cylinders (3 on the left and 3 on the right when facing the engine) which one is cylinder 2?
View 7 Replies