Ford - Escape :: 2001 - Misfire On Cylinder 4 / P0304 Code
I know I can fix this problem, but my question is which cylinder is #4? I don't see it marked on the engine. The counter guys at both my local parts supply stores (whose initials are A and O) can't even look it up for me. If #4 is on the front of the engine, then it's an easy fix. If it's on the backside, then the intake manifold has to come off to get to the plugs and coil packs. It's a bit more labor. I can do it, but I'd rather not have to.
View 1 RepliesS-10 :: 98 Chevy ODB Error Code P0304 / Cylinder 4 Misfire
I left my chevy s-10 truck sitting over the christmas (23/24/25) and it was really cold outside and when i got back i started getting a P0304 (Cylinder 4 Misfire). I replaced the spark plugs and spark plug wires. May be the cold would cause this to happen? I think I've noticed the trucks fuels efficiency drop over the past month). May be the fuel injector(s)? Is the s-10 TBI or does it have fuel injectors for each cylinder?
View 8 RepliesGolf IV / Jetta IV :: Code P0304 On Mk4 2.0 AEG - Misfire On Cylinder 4
2000 Jetta GL 2.0 AEG. I am receiving the P0304 which I have identified as Cylinder misfire #4. I read on some previous posts that I cannot be the distributor because if it was I would be receiving misfires on two cylinders. The spark plugs are OEM NGK and have been replaced recently.
View 2 RepliesPrius (2010-12) :: Code P0304 Misfire On Cylinder 4
Well, I have a big problem on prius 3, the problem is that it has a big and I mean a big body shake when I decelerate above 30 mph or slowly accelerate above 30 to 50-70 mph, when I fully accelerate, the body shake disappears. When the body shake occurs MIL comes blinking and DTC P0304 comes but not always, but the shake is only when the coolant is hot.
On the other hand, if the MIL is not on with the tester it can be seen that the cylinder 4 has misfire margin, only cylinder 4, every time. Now what I have done is to exchange the injectors, problem remains on cyl4.
-replaced the coils, problem remains on cyl4,
-clean the EGR, problem remains on cyl4,
-opened the engine to see the valves, cylinders, pistons, exchanged the ring set,problem remains on cyl 4,
Replaced the wheels, the problem is still there, now I want to replace the drive shafts.
Silverado :: 2003 - Intermittent CEL Code P0304 / Misfire On Cylinder 4
My 2003 Silverado 5.3 has an intermittent CEL. I plugged in the reader and found code P0304, misfire #4 cylinder. I changed the coil, swapped the spark plug and wire from #2 cylinder to see if the code would follow. Nope, didn't follow. I swapped the injector also, same results. My daughter decided to borrow the truck and drove it so low on fuel that the low fuel light came on in the drive way. I added about 4 gallons of fuel and now the light went off. I started the engine after a jump start, and the engine really runs rough and now won't stay running. I am thinking that the fuel filter is probably needing changed because of how low the fuel.
I haven't checked the fuel pressure yet and will do that today. Now, what really puzzles me is the intermittent part. Sometimes it will run with no problem, but then the CEL will come on and the fun begins. The Chevrolet dealer says it's caused by the valves turning in the head and when it reaches a certain spot, it detects the misfiring #4 cylinder resulting in the CEL. If I pull in the driveway with the engine missing, go back out in a short time, start the engine and it runs fine. Same thing if it's running fine and I can start it and the CEL blinks and it begins missing, but may stop and run fine. I am stumped and not so sure about the turning valves.
Grand Prix :: 1997 - Code P0304 - Misfire Only On Cylinder 4 Frequently
1997 Grand Prix 3.8 N/A 181,000 ... I have been getting a misfire only on cylinder 4 which has become more frequent. It "only" happens after the car has warmed up and I turn it off for a few minutes, for instance going in to pay for gas. When I start, it immediately starts to miss but as soon as I hit the accelerator it evens out and runs great, every time. I replaced plugs and wires two years ago with stock.
Upper and lower intake manifold gaskets were replaced around 110,000. All three coil packs have been replaced with original GM packs. I replaced my EGR valve last year due to the original was sticking. My throttle body was cleaned about four years ago. I've seafoamed through brake booster and the rest in gas tank.
I'm stumped that it corrects itself right away by giving it gas. The SES light always come on but goes off on it's own after a few cycles.
Chrysler - Ptcruiser :: P0304 Error Code - Cylinder Number Four Misfire
2006 PT Cruiser Touring Ed. The engine light came on 2 days ago, had it looked at today and the error code p0304 "cylinder number four misfire" was diagnosed. What causes that and what would need to be done to fix that problem?
View 9 RepliesFord/Mustang :: 1997 - Getting Error Code P0304 / Cylinder 4 Misfire
1997 Ford Mustang 4.6L EFI engine with 67K miles. The engine is actually now in a Factory Five Roadster. It sat on a stand for 5 years but runs well now with the exception of the code. I keep getting a code P0304 (cylinder 4 misfire) and I've checked the plug - the code seems accurate; it is misfiring.
Things I've tried:
1)swapped plugs,
2)this is a dual coil engine so I've swapped coils,
3)the #4 plug is the longest sparkplug wire so I've gotten high-performance wires,
4)heavily grounded the AL head,
5)put dielectric grease on the plug,
Still, ONLY cylinder 4 gives the misfire.
Nissan - Sentra :: Check Engine Light Came On With P0304 Cylinder 4 Misfire Code
(This is a continuation of a previous thread: [URL] ..... )
I have a 2005 Nissan Sentra with 75,000 miles on it. Several months ago (see above link) the check engine light came on with a P0304 cylinder 4 misfire code. The only symptom appears to be a rough idle/shaking every 3rd or 4th start for the first 10-15 seconds, but runs smoothly afterwards. My mechanic replaced all my spark plugs (I had new plugs put it at 50,000 miles for the same issue) of which the one from cylinder 4 was worn down much more than the rest. The problem persisted so they replaced my fuel pump and fuel filter and switched the spark coils from cylinder 4 to a different cylinder, but the code still read cylinder 4 so it wasn't the coil. That was back in October.
I took my car back in last week for the same problem and without starting my car (because the problem is worst on the first start) they pushed my car into the bay and did a smoke test, no leaks in the fuel lines. Then they checked the cylinder and said that there was "excess" fuel in the cylinder and replaced the fuel injector. Then after ~3 days the check engine came back on with the same P0304 misfire code. Previous repairs/diagnostics rule out spark plugs, coils, fuel pressure, and injectors.
Ford Excursion :: 2000 V10 - Rough Idle - P0304 Code / Cylinder 4 Misfire
I recently bought a 00 Excursion v10 2wd everything looked right no major problems. I noticed it has a rough idle and i thought it could be the EGR i went under the hood and there's no EGR in sight. I plugged the OBD reader to see if it would give any codes since the there was no check engine light on and wanted wanted to make sure it worked, It showed a P0304 code its Cyl4 misfire i checked plugs/coils and i noticed there's a little insert inside Cyl4 plugs hole in the head that it has the plug screwed on. I decided to change all the plugs and the coils and i still have the rough idle and code i can hear a ticking noise around the engine in the passenger side.
View 7 RepliesFord Excursion :: Code P0304 Cylinder 4 Misfire - Broken Rocker Mount
6.0 .... Have a code Po3o4 Cyl 4 misfire. I pulled the valve cover to remove the injector and found the right half of the rocker mount and rocker arm laying in the head. What may have happened?
View 5 RepliesFord F-150 - 1997-2003 :: CEL Codes P0304 / P0456 / P0171 - Misfire On Cylinder 4
So, my 2003 F150 4.6 that I just put back on the road after a four month break is running like crap. I took it off the road for the winter because it was missing (no codes) and didn't feel like dealing with it then but after running it for a day the CEL comes on. It shows the following:
P0304 - hoping it is a coil pack
P0456 - pending. Gas cap?
P0171 - pending. One bank too lean?
Does the 171 code possibly have to do with the misfire in Cylinder 4? I know it is impossible to tell yet but am hoping there is a potential connection.
Before I parked it in January, it was running a bit rough and stumbled on acceleration but never would show a code. Now all this. Going to change the coil first, tighten the gas cap, check for leaks and see what happens but is there anything common on these trucks that I should also be looking at?
Camry :: 2002 - P0304 Code / Misfire Occurring
We just bought a 2002 Camry with 72,000 miles 2 months ago. It now has 74,000 and while on vacation the CEL came on. I took it to a mechanic who got the code P-0304 off the computer. He swapped the number 4 ign. coil pack with the number 3 cylinder. The CEL light went off and I was able to drive the 300 miles home. The next day the CEL started again, but this time it's flashing. I changed the spark plug, it looked good, and still have the CEL on with the P-0304 code.
I've inspected the wiring to the number 4 ign. coil pack and it looks good. I'm thinking the next thing would be the fuel injector.
The car runs great, you'd never know by driving it that there is a misfire occurring. If it's not the wiring or fuel injector what should I check for next?
Golf IV / Jetta IV :: 2001 1.8T - Cylinder Misfire Code
I recently changed my spark plugs + coil packs in my 01 1.8T because it read a couple cylinder misfire codes. Drove it for a few days out of curiosity plugged the code reader in again and it's still reading misfire codes. What could the issue be still?
View 6 RepliesSanta FE SM (2001-06) :: Code P0302 Misfire In Cylinder 2
I just purchased a 2005 Santa Fe, 4WD, 2.7l..the engine has a miss...the code that came up was "misfire in #2 cylinder"..I checked the coil pack...and the wire harness just crumbled..so I replaced the coil pack...reset the code..and it was good for a couple of days...I got through inspection...today I put on the A/C..and the engine got rough..the check engine light came back on..same code..misfire in #2..I'm thinking the injector or what else could it be? plug? wire?
View 3 RepliesSanta FE SM (2001-06) :: Code P0306 Came Up - Cylinder 6 Misfire
I have a 2004 Santa Fe with the 3.5. Today I started it and the check engine light came on. It was not on before this. (We had a lot of wind and rain from the storm but nothing major.) And seems to be running fine. I went to the auto parts store and they ran a diagnostic and the Code P0306 came up #6 cylinder misfire. They said probably Spark plug, wire or coil for #6, then went to look up code in computer and did not have my truck so they went with Kia or Domestic, which gave different possibilities for a code P0306.
They had me buy some fuel injector cleaner as injector was on the list. The light is still on so I guess the cleaner was not the magic bullet. I spoke to a lady at another auto parts store who is a wiz when it comes to cars and has been around them and fixing them a really long time. She says the Code P0306 is Spark Plug, wire, coil #6. She has a 4cyl Hyundai car not truck and she had the code for her #4 misfire in the past and she started her repair cheapest first, Plugs, wires her code was still there she then changed the coil and that did the trick for her.
I on the other hand can't do this stuff myself. Can't afford the dealer anymore or to have a shop do a tune up AND coil if I don't need all new plugs and wires just a coil as they will charge a lot to do a lot all. And it may not need it or even be any of those things. I also suspect the dealer and shops will want to still hook up their computers to do an costly diagnostic because the light is on, even though I know the parts store already came up with a code P0306 twice. Spoke to the dealer on the phone and he already basically said they would want to do that first for $100 plus the cost of repair.
I brought the truck new. It now has 91,500 miles on it and the dealer has already done two tuneups on it in that time, Plugs and wires. I hear it probably shouldn't have even needed these tuneups in this amount of millage? So the last one was probably about 2 years ago and a few thousand miles maybe a guess 10,000-20,000 miles ago. Do you think a plug and wire would be bad already in that few miles?
Santa FE SM (2001-06) :: CEL Came Up With A Code P0303 - Cylinder 3 Misfire
I got a check engine light. I went to Auto zone to get it read & they came up with a P0303 - Cylinder 3 misfire. Since I bought the vehicle a couple of months ago, I don't know when the plugs were last changed, so I decided to change them. However . . .
Is there a secret to getting the plug boots & wires out of the hole and off the plug without wrecking the wires?
Ford Ranger / B-Series :: 2008 - CEL Code P0304 / Misfire
2008 Ranger 3.0L. I am trying to figure my next step in diagnosing a #4 misfire. At regular speeds I really dont hear it or feel it, mostly at idle warm or cold. 3.0L with 275,000 kilometers on it , reg oil changes.The CEL is on, but not blinking. Pulled a p0304 code. I then changed out the bosch plugs I had in with ford plugs and wires. The #4 plug looked okay just bigger gap. Still got the code.
I hooked up a sparkplug light to the coilpack and did not see any missing flashes . Changed fuel filter, checked fuel pressure,all within specs. Changed the oil and did not see anything in it. I read that it could be an injector but I have to remove the intake manifold to get at it. I also read to check compression. I figured if I have to take off the manifold I would put a new injector in, instead of switching them around. What is the most common cause for this code?
Santa FE SM (2001-06) :: 2002 - Code P0302 / Misfire On Cylinder 2
I have a 2002 Santa Fe 4 cyl that is giving me a problem that I could use some advice on tracking down & fixing . First & most important is a code P0302 # 2 Cyl misfire. How to check the ignition coil pack , injector ,& wire for this cylinder in home garage with normal tools & meter . Is there a you tube displaying how to do this step by step ?
The other problem which I don't have the code for at this time is that some part of the exhaust is not getting warm enough & this also put's the check engine light on . Will get back on this one when I solve the main problem Misfire.