Ford Ranger / B-Series :: 2003 3.0 - Misfire On Cylinder Six / Running Rough And Check Engine Light On
I have a 2003 ranger and have had ongoing problems with misfire cylinder six and have had three different mechanics diagnose the problem as a bad ground. I have replaced all plugs, wires, coil pack, injectors and am constantly pulling the plug on cylinder six, cleaning and often replacing, I also disconnect the battery so it resets the check engine light and it runs fine for about 100 miles and starts running rough again and on goes the check engine light. I have 134000 miles and have maintained it since new.....
View 4 RepliesFord Ranger / B-Series :: 2002 - Cylinder 2 Misfire Code / Idle Rough When Warms Up
I bought this from my brother in better than mint condition. Always maintained. Its generating a cyl #2 misfire code.
It starts and runs like new when cold, but when it warms up, it idles rough, and generates the code. after 1500 rpm it smooths right out and runs fine.
He had it to the dealer just before I bought it and they told him needed a new engine.
I am thinking bad injector, since what seems to be happening is, when cold it gets more fuel, or when u rev it gets more fuel, but at an idle and warm, it doesn't seem to be getting enough maybe. And I see from the maintenance records, a couple of other injectors have been replaced as well.
I think the dealer got tired of replacing injectors under warranty and tried to milk him for a new engine.
2002 ranger extended cab 2wd, 3 door, 232,000 kms 5 speed 3 liter V6, new glass and clutch..
Tiguan :: 2009 - Cylinder Misfire After Coil Pack Swap?
I recently did a coil pack swap to determine if that was the cause for a cylinder 1 misfire. Left to right on my 2009 se tiguan, I changed 1 to 2, 2 to 1, 3 to 4 and 4 to 3. I recently ran into the cylinder misfire again, this time on cylinder 4. The problem is, I do not know which coil fires which cylinder. I've looked around quite a bit and can't seem to find it.
View 6 RepliesFord Ranger / B-Series :: 2002 XLT - Rough Idle - Misfire On Cylinder 3
I have a 2002 ford ranger xlt 3.0 i just rebuilt the entire motor about a month ago and was having a high idle problem for the longest time. turns out i had the iac on backwards. but now that it idles down around where its supposed to it has a rough idle has a little shake to it. starts up right away but when i drive down the road around 3000-3500 rpms its missing on cylinder #3 from what the code I am getting "multiple cylinder misfire, #3 cylinder misfire" I've replaced plugs and wires. camshaft pos sensor. I am getting 65 lbs of fuel pressure. spark on all cylinders. I am really at a dead end here. Also every time I take the plugs out to look at them they look brand new.
View 14 RepliesFord Ranger / B-Series :: 2001 - Rough At Idle / Misfire In Cylinder 1
So I have a 2001 ranger 2.3l . Runs very rough at idle.code says misfire in cyl.#1. I have changed plugs, wires, coil packs all motocraft. I did a compression test..
#1.170
#2 180
#3. 185
#4 . 180
Compression seems fine,but where do i go from here? Anything else i can check/replace to solve this?
Ford Ranger / B-Series :: 2000 - Misfire On Cylinder 4
This has been an issue for about 8 months now. I'm getting a misfire on cylinder 4. So far compression test, new gas filter, fuel injectors cleaned, spark plugs and wires replaced. coil pack replaced. Heater valve was leaking but was replaced.
View 10 RepliesFord Ranger / B-Series :: 2000 - CEL On - Misfire On Cylinder 5?
OK, got a check engine light today when I fired up the Ranger.
Took it down and got the codes read it have a miss fire on cylinder 5. Picked up some plugs and wires, got to get those E3's out of there, but kind of think that's really not going to fix the problem. So that probably leaves the coil pack or injectors.
So what's the consensus on the best coils to use?
Also, being an 18 wheeler for more years than I care to remember, I've learned swapping just 1 injector is never the way to go. So whats the best type of injectors to get and where the best place to get them should it come to that?
Oh, it's a 2000 3.0L Flex fuel 5 speed.
Ford Ranger / B-Series :: 2000 - CEL On / Cylinder 4 Misfire
My parents 2000 Ranger has an CEL for cylinder 4 misfire, but it will clear on its own and then start up days/weeks later, is this common? Could it be an injector?
View 3 RepliesFord Ranger / B-Series :: 2000 4.0L - Cylinder 4 Misfire Sometimes
I have a misfire mystery going on in my girlfriends 00 ranger. What is going on, is there is an intermittent misfire on #4. I have an ultra gauge hooked to it, so most of the time when it does it, it will flash a pending code. A lot of the time, the pending code will go away, but sometimes it will set the PO304 code.
First I tried a tune up. New plugs and wires, air cleaner, cleaned out the throttle body. This cured it, for a short while. Then we were back to the pending code / setting code for #4.
When I pull the plug on #4 it is sometimes wet with gas. If you put a new plug in it runs fine for a while. In fact the last time we took a several 100 mile trip with it right after plug change, and it ran great. The pulled plugs re always in good condition with no burn, oil, chips or glazing. I have been using the standard autolites that are in advance auto's computer for that engine. No issues with the other 5 so I figure they re good enough.
The day after we came back I get the call... Honey its doing it again. Often to the point of having no power at all.
But it will clear itself usually, if not a new plug for #4 will cure it immediately.
So I thought something is killing this plug.... Or flooding it. SO I ran 2 cans of sea foam though it, put in a new plug and an new wire. It fixed it for a week then it did it again.
Ok I think... maybe the coil pack is bad either killing the plug or just not firing it at all? So since the pack has never been change in its nearly 300K life (to my knowledge, shes had the truck since about 60K) What the heck.... a new coil pack for the old thing.
I have not had the chance to clean the MAF but we are talking misfire on one cylinder, every now and then with no real conditions that set it off. More often than not its a pending code that you can even hear or feel and other times its a full blown miss that drags the truck down. Well for a short while until it clears up or I replace the plug.
3 cans of seafoam surely would have cleared a sticky injector. I realize it could be a bad wire to that injector but I have not had the time to tear the fiddle bits off to get to it to clean and test it... or just replace it.
Honestly Ive had a lot of cars and trucks, I don't remember ever having to replace an injector. Ive had bad wires to them but they misbehave ALL the time. This problem is so intermittent its freaky.
She says it does it mostly when its cold or not totally warmed up. Almost always, by the time the engine is hot it goes away.
And hot for this truck is over 185F, which I think its too cold to be running and the thermostat needs changed BUT she thinks cool=good. I keep telling her no, cool is often not good, the engine needs to be up to the operating temp.... which to me means 190-200. Her ranger runs between 170-180 all the time. I doubt thats causing the problem but still.... I think new thermo is in order.
My thinking is since it runs so cool all the time, the issue might be related to a spike in the temp over 180 ish, that gods forbid is opening a crack somewhere to suck air or lose compression.
And a compression test is my next step on #4 if/when it does it again. Now I have had cracked valves before, I don't recall them acting this way. After all sometimes the thing will go 100s of miles under different driving conditions and run fine. I don't think a cracked valve would be that nice.
Shes getting @18 MPG mixed driving, when it runs t runs like a bear. It always fires right up. There is no smoke, white or black. There is no water in the oil, no oil in the water. No audible exhaust leaks. No ticks knocks or oddball noises. For its age and miles almost 300K it runs perfectly.
Well until it has its intermittent issue with the misfire, that isnt bad enough to actually set the code.
Ford Ranger / B-Series :: 2000 - Inconsistent Misfire On Cylinder 1 And 2
I have a ford Ranger with a 2.5 and 231,000 miles. I bought this truck with a misfire on #1 cylinder. drove it home and started it a couple days later and still misfire on #1 but as soon as you rev up the motor the #2 starts misfiring as well and dies. start it back up and misfire on #1, rev up the throttle and misfire on #2 also.
Here's what i have done so far. intake gaskets, plugs and wires, checked fuel pressure (good), swapped injectors on 1 and 2 with different injectors, timing belt, tensioner, swapped coils from primary to secondary no change, checked compression and all 155 and above.
I have talked to everyone i know and am getting no where. the truck can sit and run for a hour with a minor misfire on #1 but as soon as you hit the gas it starts another misfire on #2. I am thinking it is a ecm issue.
Ford Ranger / B-Series :: 1999 - Code P0305 Cylinder 5 Misfire
I have a 1999 ford ranger 3.0 6 cyl with 211,110 miles It started running rough without any previous warning signs. In idle its barely noticeable, once i put it in gear it gets rougher and when driving around 40 to 45 mph it roughly shakes and shimmies. Once I get past the 40 to 45 mph range it settles back down. Is there a specific issue that would cause that at that speed. When going up over a bridge the check engine light blinks.
I changed the spark plugs and new wires and it offered no success even though one of the plugs were black (to much gas). I have borrowed a diagnostic tool and got P0305 cylinder 5 misfire, I am thinking fuel injector to replace, what else should I be looking at?
Ford Ranger / B-Series :: 1999 - 304 Code / Misfire In Cylinder Number 4
1999 ranger 155k 3.0 flex fuel. 304 is misfire in cyl number 4... I replaced the plugs and wires and checked the coil. the compression in cyl 2, 4, 5, 6 and got 80-90 psi so they are consistent but consistently bad right, it may be my compression tester.
The #4 plug was spotless after running 5 min, the #5 plug had some black on it already. Its hard to tell but it seems I had fuel residue on the plugs on cyl 5 and 6 but none on 4? Whats next pulling the intake to get to the injector?
Ford Ranger / B-Series :: 1995 - Misfire In Cylinder 2 / CEL Flashing And Code P0302
I have a 1995 ford ranger 2.3 L dual coil packs new plugs, wires, coil packs, tps, idle air sensor, internal temp sensor, and a replaced mass air flow sensor from wrecker. That all said my one son missed a plug when i replaced it , it had no tip left on it , but since then i now have a misfire in cylinder 2 where the olther plug was found and replaced ...
Gap for plugs are .44
Used the wrecker maf to see if it would clear a p0113 which it did. I am stumped on why at approx. 30 minutes of driving that the cel will flash then set a p0302, no other codes no fuel smell. rechecked plugs all are clean haven't been able to check fuel pressure yet, and i out a can of seafoam in the tank to see if it clear out injectors.
Besides all, I will check injector to see if I hear anything but I'm stumped. Also we have to have an emission test so is it best to fail the test and will it show me what I'm missing.
Ford Ranger / B-Series :: 2003 - Misfire And Rough Running / Flashing CEL
2003 Ranger FX4 Flareside
4.0
Automatic
145,000 Miles
Here's my issue: My Ranger has been running like a dream until yesterday.
I took off on a parts run for my sons Ranger. I got to a stop sign and as I stopped, it started missing and barely running. I nursed it back home and checked the flashing CEL. It was giving me a misfire on #3.
Since I had been planning on changing the plugs and wires, I dove in and got it done hoping that was the cause of the misfire.
Started it up, same thing. I went to the next obvious item: coil. Replace it, still running like crap. Gave up for the night.
Today, I thought I would dig in using the tips here on the forum. Did the spray down...no errant spark anywhere. Tested fuel pressure: 65psi no drop in pressure on acceleration.
Started pulling wires off the coil one by one. Four of the wires resulted in running worse. 2 had no effect. #3 and #6. The coil was producing plenty of spark on all 6 ports.
At this point I was sure it had to be 2 bad injectors. Since I couldn't get injectors tonight, I moved them around after cleaning them a bit and tried my wire test again. The problem stayed on the back 2 cylinders!?!
I tested for voltage on the back injector plugs and I am getting voltage. I also used a stethoscope to listen to all of the injectors. The back 2 seem to remain silent. I have also unhooked the battery for 20 minutes to reset the PCM. Still missing and running rough....
Here's a list of what I have done:
Autolite Double Platinum APP5144 plugs. .062 gap
Autolite Pro Series wires #97051
BDW E97P Coil
New air filter
What should I do next? I really don't know where to go next.......
Ford Ranger / B-Series :: 2000 - Check Engine Light / Misfire On Cylinder 5
OK, got a check engine light today when I fired up the Ranger. Like I posted previously it is running kind of rough so guess I know why now.
Took it down and got the codes read it have a miss fire on cylinder 5. Picked up some plugs and wires, got to get those E3's out of there, but kind of think that's really not going to fix the problem. So that probably leaves the coil pack or injectors.
So what's the consensus on the best coils to use? Also, being an 18 wheeler for more years than I care to remember, I've learned swapping just 1 injector is never the way to go. So whats the best type of injectors to get and where the best place to get them should it come to that?
Oh, it's a 2000 3.0L Flex fuel 5 speed.
Ford Ranger / B-Series :: 1996 4.0L - Misfire On Cylinder 3 / Check Engine Code P0303
Got a 1996 Ford Ranger with the 4.0L in it that has a misfire on the #3 cylinder and giving check engine code: P303. Have tried new plugs, wires, distributor, switching out the coil pack with a known good, checked injectors for pulse, checked injectors, moved injectors and still the misfire remains on #3. Removed the valve covers and all appears to be well.
View 14 RepliesFord Excursion :: 2000 V10 - Rough Idle - P0304 Code / Cylinder 4 Misfire
I recently bought a 00 Excursion v10 2wd everything looked right no major problems. I noticed it has a rough idle and i thought it could be the EGR i went under the hood and there's no EGR in sight. I plugged the OBD reader to see if it would give any codes since the there was no check engine light on and wanted wanted to make sure it worked, It showed a P0304 code its Cyl4 misfire i checked plugs/coils and i noticed there's a little insert inside Cyl4 plugs hole in the head that it has the plug screwed on. I decided to change all the plugs and the coils and i still have the rough idle and code i can hear a ticking noise around the engine in the passenger side.
View 7 RepliesCelica :: 2000 1zzfe Engine Was Running Rough - Cylinder 1 Misfire
Okay so last year i bought a 2000 celica gt manual with 50,000 miles, and currently has 67,000 miles. A few days ago I started to notice the engine was running rough and then about 10 miles later the chack engine light came on. I promptly went to the auto parts store to read the code. I was informed I have a cylinder 1 misfire. Naturally i replaced the spark plugs with NGK iridium, reset and rechecked engine code. Same code. Next i swapped the coils from 1 and 2, reset and rechecked. same code. I then swapped fuel injectors from 1 and 3, rest and rechecked. Same code. So now i am a bit stumped.
Only faulty equipment prior to this incident would be 2nd gear synchronizer. Only applicable above 5,800 RPM.
Ford Ranger / B-Series :: 1998 - Running Rough And Now Getting P1151 Code
1998 Ranger 4x4 4.0 Ltr - Runs rough ever now and then and CEL giving P1151 code. Upper and lower intake gaskets have been replaced.
View 14 Replies