1996 Blazer - Flashing Cel Light P300 Multiple Cylinder Misfire?
So my 96 blazers cel started flashing and the truck started running extremely rough. I changed the catalytic converter and the o2 sensor that is in the pipe. Made no difference. So I knew my intake manifold gasket has a leak so I changed the gaskets and put knew bolts in. I wasn't thinking and took my distributor out and forgot to mark the timing. So played like heck getting it in timing again. Took a bit cause I didn't realize there was two timing marks. So got it started again was running really rough so thought 180 off turned it nothing. So put it back started it up still running very rough and flashing cel so put a new crank sensor and cam sensor in and a ignition coil in. No dif still. Could it be the egr or ECM?
View 12 RepliesToyota - Prius :: Check Engine Light Came On - Code PO301 / Misfire On Cylinder 1
I have a 2007 Toyota Prius with just under 30,000 miles. Yes, I don't drive all that much, which makes the Prius the perfect car. I get it serviced every 6 months by the dealer. So far, other than oil changes, the only actual maintenance has been tires, a 12 volt battery, and a $300 "inspection".
A few weeks ago the "Check Engine" light came on. I pulled the code P0301, which translated to "Misfire on cylinder 1". The car was running great at that time, and since clearing the code it has continued to run without the light coming on again. Given that my maintenance is more time-related than mileage-related, it's possible that the ignition system needs attention. However I'm reluctant to bring that up at my next maintenance appointment, because the guy writing up the service order will always answer "Yes" to every "Do I need ..." question.
Prius (2004-09) :: Check Engine Light With PO301 Cylinder Misfire Code
I bought my 2008 Prius 9-14 with 29,000 miles on it. (rebuilt title-big mistake I now know). I found out after I bought it that it had sat for 5 years before it was rebuilt) I figured it was a miracle the hybrid battery even worked.
I had no problems until 2-4-15 when check engine light was flashing and the car was shaking. The local mechanic said was the “clutch” (torque converter), took the engine and transmission out of the car to fix it ($2200). But he realized the mass air flow sensor (MAP) was not working even after he put a new one in so had me take the car to the Toyota dealer. The dealer found a cut in the engine harness and advised me to replace the harness which he said would cost $2800. The local mechanic saw the cut via my cell phone photo and offered to fix it for free which he did.
The next day check engine light comes on after driven 25 miles with code PO 301. (means misfires in cylinder one). The local mechanic switches cylinder 1 with 4, same code the next day, local mechanic switches the coils to the cylinders, still the next day the same code. He switched the fuel injectors. Same problem of cylinder 1 misfire. He cleaned the oil out of the intake manifold, did fuel injection cleaning, and cleaned gunk out of the fuel line. Car would drive good about 20 miles then same check engine light, same code, sometimes code PO300 (random multiple misfires).
Nissan - Sentra :: Check Engine Light Came On With P0304 Cylinder 4 Misfire Code
(This is a continuation of a previous thread: [URL] ..... )
I have a 2005 Nissan Sentra with 75,000 miles on it. Several months ago (see above link) the check engine light came on with a P0304 cylinder 4 misfire code. The only symptom appears to be a rough idle/shaking every 3rd or 4th start for the first 10-15 seconds, but runs smoothly afterwards. My mechanic replaced all my spark plugs (I had new plugs put it at 50,000 miles for the same issue) of which the one from cylinder 4 was worn down much more than the rest. The problem persisted so they replaced my fuel pump and fuel filter and switched the spark coils from cylinder 4 to a different cylinder, but the code still read cylinder 4 so it wasn't the coil. That was back in October.
I took my car back in last week for the same problem and without starting my car (because the problem is worst on the first start) they pushed my car into the bay and did a smoke test, no leaks in the fuel lines. Then they checked the cylinder and said that there was "excess" fuel in the cylinder and replaced the fuel injector. Then after ~3 days the check engine came back on with the same P0304 misfire code. Previous repairs/diagnostics rule out spark plugs, coils, fuel pressure, and injectors.
Santa Fe (DM - 2013+) :: Check Engine Light Code P0303 - Cylinder Misfire
I own the 2014 Santa fe turbo 2.0 litre limited which has 4000 km on it. Within 210 km the engine light came on 3 times. I took it into the shop and they ran a code of P0303 which is a misfire, they changed the coils #2 and #3 and cleared the code. The second time it showed the same code but the shop said it was in the history so that is why the same code came up again. They ran an update ECM? and all was good. Now the 3rd time they tell me no code has come up and can't do anything about the engine (they cleared it) but it was like chasing ghosts. My vehicle runs great so not sure why I am constantly having this issue.
View 68 RepliesFord Ranger / B-Series :: 2000 - Check Engine Light / Misfire On Cylinder 5
OK, got a check engine light today when I fired up the Ranger. Like I posted previously it is running kind of rough so guess I know why now.
Took it down and got the codes read it have a miss fire on cylinder 5. Picked up some plugs and wires, got to get those E3's out of there, but kind of think that's really not going to fix the problem. So that probably leaves the coil pack or injectors.
So what's the consensus on the best coils to use? Also, being an 18 wheeler for more years than I care to remember, I've learned swapping just 1 injector is never the way to go. So whats the best type of injectors to get and where the best place to get them should it come to that?
Oh, it's a 2000 3.0L Flex fuel 5 speed.
Ford - F150 :: Check Engine Light Started Flashing / Cylinder 4 Misfire Code
1997 Ford F150 - 133K Miles - 6cyl - 4.2L. This is a truck that gets less than 2K/year put on it. Has had "issues" with worn bearings and holding oil pressure for a few years now. Yesterday, the check engine light started flashing (as opposed to solidly lit) and the code came back as a cylinder #4 misfire (only the one code). The truck was clearly not firing on all cylinders and at idle, ran terribly (couldn't be driven). I just did a compression test on all the cylinders and all measured around 140-145psi except the #4 which read almost 170psi. I rechecked this a few times as well as a couple of the others and am now sure of the results. What could cause this one cylinder to have a higher compression ? Is whatever is causing this increase in the compression, also be the cause of them misfire ?? I'm stumped here and quite frankly, expected the compression on the #4 cylinder to be really low as opposed to the others.
View 13 RepliesFord - Ranger :: 1997 - Check Engine Light On With P302 Computer Code / Misfire On Cylinder 2
1997 Ford Ranger with 190K miles has check engine light on with P302 computer code, meaning misfire on cylinder 2. Engine runs rough at idle only once it warms up, which only takes a minute. It is usually fine while driving, but it's a lot easier to feel a misfire at lower RPMs than at higher ones. Added fuel injector cleaner to gas for a couple tanks, no change. My mechanic has checked spark plugs, fuel injector, o2 sensor, and everything is ok. Dry compression test shows good compression. He thinks it may be a valve sticking, which means a valve job: expensive. Is there anything else that can be done? Why is there no misfire when it is first started?
View 9 RepliesCamry :: Check Engine Came On And Showed P300 Misc Engine Misfire
I replaced my seven year old original battery on my 2008 Camry V6 SE. The car started ok, but the check engine came on and showed the P300 misc engine misfire. The car ran fine. The original battery failed the load test at the local auto parts store. I replaced the battery and the check engine light went out. I have noticed better engine performance and better transmission shifting too.
View 3 RepliesHonda - Cr-v :: 2001 - Check Engine Came On / Cylinder Misfire Code
I have a 2001 Honda CRV with about 140,000 miles. It is an upstate NY car, so has seen its share of salt and rough winter driving, has a little bit of rust.
I recently brought it in for repairs because it was overheating. It was over the holiday weekend and I had a job interview to get to so I brought it a chain, which was the only open mechanic I could find. They told me there was a coolant leak and replaced the radiator.
The next day, the check engine came on. Cylinder misfire code. I took it back to them and they wouldn't give me a straight answer on what was going on but insist they told me that would happen and it needed more repairs which I had apparently refused. They told me it's probably the spark plugs/wires are old but maybe there's more damage, but basically that they didn't want to deal with it.
So I brought the car to my regular guy. He says, yeah it needs a tune-up. So he replaces the spark plugs and wires etc and gives it back. I drove it for a day and the light came back on. So I brought it back to him again and he refused to do anything. Wouldn't give me some possible causes or explanations, just says come pick it up. Didn't say stop driving it, take it to a dealer, he just reset the check engine light and said its probably fine.
The next time I drove the car, while it was warming up the check engine light was flashing. By the time the engine was warm the light had stopped flashing and was on.
Ford Ranger / B-Series :: 1996 4.0L - Misfire On Cylinder 3 / Check Engine Code P0303
Got a 1996 Ford Ranger with the 4.0L in it that has a misfire on the #3 cylinder and giving check engine code: P303. Have tried new plugs, wires, distributor, switching out the coil pack with a known good, checked injectors for pulse, checked injectors, moved injectors and still the misfire remains on #3. Removed the valve covers and all appears to be well.
View 14 RepliesPassat (B5) :: V6 Check Engine Light - Misfire In Cylinder 4
I'll try to break this down as best I can. I went to my mechanic this am with a check engine light. My suspicion is 02 sensors. This was confirmed as a problem area, but separate they said I had a spuratic misfire in cylinder 4. With that info, i pulled the plug to inspect (I had just installed new ngks in it and they have 18,000K on em.
I put beldon wires on about 8k ago.) plug looked to be normal, but there was definitely a puddle of oil from the valve cover leaking. Oil went into the cylinder head but I didn't really think that was an issue. Nothing abnormal jumped out at me so I reinstalled plug and checked all wire connections at both ends and called it a day.
Then I drove it. Check engine light flashing. Major performance stutters, etc. I drove it for about 20 miles and hoped it was just the oil raising hell in there and it would burn off eventually. It hasn't gone away yet. Maybe coil pack. Can the single portions of that pack be replaced, all i see them sell is the full three as a unit.
Chevrolet - S-10 :: Check Engine Light Come On / 4th Cylinder Misfire
2000 Chevy S10 pickup
Had the check engine light come on, and when I checked on the code it gave a 4th cylinder misfire. Autozone instructed me to simply replace my spark plug with a new oem plug.
I replaced the spark plug as instructed. After about an hour of driving, the check engine light goes off and I think, great! Problem solved. However, another hour of driving and the check engine light is back on again, without going away.
I headed back to autozone to get a readout, just to find that it's the same code. So I put another spark plug in. Same result - check engine light goes off after an hour, only to come back on again permanently after another hour.
Now, normally I would think, this must be the spark plug line that needs replacement,however I am sure there must be some clue in the fact that the check engine light turned off for an hour.
By the way, not sure if relevant, but I also found a lot of build up around the spark plug before I initially changed it.In fact, there was so much that I had to scrape around the plug with an awl, and blow out the crud with a compressor,just to get my socket into place without there being crud in the way.
Any clue what that check engine off/on clue might be?
Passat (B6) :: Check Engine Light - Cylinder 4 Misfire
Got the flashing check engine light and loss of power for few seconds and then the light stayed still, from time to time it blinks for few secs, usually when I push the gas pedal little bit more but it stays still, flashed only twice in 2 days for seconds. I connected computer (not VAG) and it says "Cylinder 4 misfire". I have app scheduled with my mechanic this Thursday, but still need to commute to work. Is it safe to drive?
View 7 RepliesPrius (2010-12) :: Check Engine Light On Due To Cylinder 1 Misfire
I plugged in a OBD2 reader and its show misfire on Cylinder 1.
I haven't driven the car for 4 days, and when i started the engine this morning, the engine show knocking when the regular engine kicks in (rough). i will be bringing the car in tomorrow (dealer). my car is a 2011 with 16k miles, strange for this to happen so early in age.
Elantra XD (2001-06) :: Check Engine Light (cylinder 3 Misfire)
As the title says I have plugged a code reader in and it says "cyclinder three misfire". So I pulled the plugs and good god they were nasty. Some having a gap of 80-90 thousandths of an inch. So I figured the plugs were the source of the problem, thus I replaced them but to my dimise the check engine light is still on, and still reading the same ol' "cyclinder three misfire". I have put 350 miles on it in 24 hours of changing it to allow for proper time of the circuit cycling for the light to change but not sure if it takes longer...?
I also went ahead and checked the plug wires resistance when I had the plugs pulled and they ranged from 1.5-2.5k ohms shortest to longest (cylinder 4-1). And if your curious the magic cylinder three was around 2k ohms for however long that wire is, my guess would be 18 inches. Would this be out of tolerance, I know the norm is 10k ohm for every 12 inches or so...?
My next guess would be replacing the power pack or I guess you car guys call it the "ignition coil"...? I will say that the car does run much smoother after replacing the plugs.
Honda - Odyssey :: Cylinder 4 Misfire - Check Engine Light
Honda Odyssey 2005 – 176000 miles. Cylinder 4th Misfire – check engine lightHonda has about 176000 miles. When cold – before warming up – it acts like nothing is wrong – as it gets warmer – to the middle of the temperature gauge – it misfires.And runs rough. Evaluation: Honda Dealership thinks it is a cracked Valve or needs adjustment – they have replaced a spark plug and swapped coils. Not for sure.They think if that is not the case then there could be additional problems.Question: Why does it act normal when cold ? How can we confirm if it is the valve and not cracked head?
View 15 RepliesFord Excursion :: Check Engine Light And Cylinder 5 Misfire
So when I bought the car, it had a check engine light. I had it checked it said cylinder 5 misfire. I assumed it was the glow plug so I bought it and replaced the glow plugs myself. Check engine light went away for about a day then came back on. Got it checked again and still said cylinder 5 misfire. This is my first diesel and I'm clueless as to what's wrong.
2001 7.3 Limited with 232k miles Bergen County NJ.
Dodge - Intrepid :: 2004 - Code Keeps Coming Up P300 Random Misfire
The "check engine" light on my 2004 Dodge Intrepid has been on (not blinking though) for months and, after putting new spark plugs, wires, ignition coils, 02 sensors, cam sensors and other things, the code that keeps coming up is P300 random misfire. After a few of the above items were put in (particularly the 02 sensors), the light would go off for a day or two but then always come back on. Because of this "random misfire", the car basically has no power when I push the accelerator down (at least until it warms up for a while and even then too sometimes).
View 1 Replies