Toyota - Prius :: Check Engine Light Came On - Code PO301 / Misfire On Cylinder 1
I have a 2007 Toyota Prius with just under 30,000 miles. Yes, I don't drive all that much, which makes the Prius the perfect car. I get it serviced every 6 months by the dealer. So far, other than oil changes, the only actual maintenance has been tires, a 12 volt battery, and a $300 "inspection".
A few weeks ago the "Check Engine" light came on. I pulled the code P0301, which translated to "Misfire on cylinder 1". The car was running great at that time, and since clearing the code it has continued to run without the light coming on again. Given that my maintenance is more time-related than mileage-related, it's possible that the ignition system needs attention. However I'm reluctant to bring that up at my next maintenance appointment, because the guy writing up the service order will always answer "Yes" to every "Do I need ..." question.
Prius (2004-09) :: Check Engine Light With PO301 Cylinder Misfire Code
I bought my 2008 Prius 9-14 with 29,000 miles on it. (rebuilt title-big mistake I now know). I found out after I bought it that it had sat for 5 years before it was rebuilt) I figured it was a miracle the hybrid battery even worked.
I had no problems until 2-4-15 when check engine light was flashing and the car was shaking. The local mechanic said was the “clutch” (torque converter), took the engine and transmission out of the car to fix it ($2200). But he realized the mass air flow sensor (MAP) was not working even after he put a new one in so had me take the car to the Toyota dealer. The dealer found a cut in the engine harness and advised me to replace the harness which he said would cost $2800. The local mechanic saw the cut via my cell phone photo and offered to fix it for free which he did.
The next day check engine light comes on after driven 25 miles with code PO 301. (means misfires in cylinder one). The local mechanic switches cylinder 1 with 4, same code the next day, local mechanic switches the coils to the cylinders, still the next day the same code. He switched the fuel injectors. Same problem of cylinder 1 misfire. He cleaned the oil out of the intake manifold, did fuel injection cleaning, and cleaned gunk out of the fuel line. Car would drive good about 20 miles then same check engine light, same code, sometimes code PO300 (random multiple misfires).
Accent MC (2006-11) :: 2008 - Code For Cylinder 1 Misfire / CEL Flashing
I have a 2008 Hyundai Accent that is giving me one heck of a headache. I keep getting a code for number 1 cylinder misfire. When you start it up it runs fine for a while then the CEL will flash and it will start running rough. As soon as I shut it off and restart it, it runs fine. I even experimented with it this morning on the way to work. It started running rough doing 60, I put it in neutral, turned the car off and then right back on, put it back in gear. It ran fine the rest of the way to work. I have swapped coil packs, fuel injectors, spark plugs, and have even hang tested another ECM. Still number 1 cylinder misfire.
View 8 RepliesAccent MC (2006-11) :: CEL Flashing / Rough Idle - Cylinder 1 Misfire
I did not get the specific cel code but its what the guy told me at autozone.
Long story short. Washed engine, let sit for about 30 mins. Car started with flashing CEL and was "puttering" and very rough idle. Drove home took intake off and replace with stock, took spark plugs out and they were not wet. Then let it sit for about 15 mins. Started just fine. No CEL at all.
The accent saved the CEL and the guy told me that Cylinder 1 had a misfire.
My question is, should I do anything now even though the car seems to be running ok?
Ford Ranger / B-Series :: 1995 - Misfire In Cylinder 2 / CEL Flashing And Code P0302
I have a 1995 ford ranger 2.3 L dual coil packs new plugs, wires, coil packs, tps, idle air sensor, internal temp sensor, and a replaced mass air flow sensor from wrecker. That all said my one son missed a plug when i replaced it , it had no tip left on it , but since then i now have a misfire in cylinder 2 where the olther plug was found and replaced ...
Gap for plugs are .44
Used the wrecker maf to see if it would clear a p0113 which it did. I am stumped on why at approx. 30 minutes of driving that the cel will flash then set a p0302, no other codes no fuel smell. rechecked plugs all are clean haven't been able to check fuel pressure yet, and i out a can of seafoam in the tank to see if it clear out injectors.
Besides all, I will check injector to see if I hear anything but I'm stumped. Also we have to have an emission test so is it best to fail the test and will it show me what I'm missing.
Ford - F150 :: Check Engine Light Started Flashing / Cylinder 4 Misfire Code
1997 Ford F150 - 133K Miles - 6cyl - 4.2L. This is a truck that gets less than 2K/year put on it. Has had "issues" with worn bearings and holding oil pressure for a few years now. Yesterday, the check engine light started flashing (as opposed to solidly lit) and the code came back as a cylinder #4 misfire (only the one code). The truck was clearly not firing on all cylinders and at idle, ran terribly (couldn't be driven). I just did a compression test on all the cylinders and all measured around 140-145psi except the #4 which read almost 170psi. I rechecked this a few times as well as a couple of the others and am now sure of the results. What could cause this one cylinder to have a higher compression ? Is whatever is causing this increase in the compression, also be the cause of them misfire ?? I'm stumped here and quite frankly, expected the compression on the #4 cylinder to be really low as opposed to the others.
View 13 RepliesAccent LC (2000-05) :: Cylinder 4 Misfire When Refueled
I have a 2004 Accent Gt with only 43k miles on it and I am getting a cylinder 4 misfire when I refuel. I have replaced the 4 spark plugs. The original code was random multiple and now it is just cylinder 4. I tried to swap 2 spark plugs to see if maybe there was something wrong with the plug but the misfire did not move to another cylinder. I've read about maybe swapping fuel injectors, where I can find directions on how to do that?
View 8 RepliesAccent LC (2000-05) :: 2002 1.5L - Misfire On Cylinder 3
I have an 02 Accent 1.5L that has a misfire on #3. I have replaced the head gasket, valve cover and gasket, intake gasket, timing belt, yes it was top dead center, MAF, Charcoal canister sensor, MAF, plugs, wires, coil pack, injector #3, and the compression in #3 is 130. What else to check. No other codes.
View 3 RepliesAccent MC (2006-11) :: 2010 GL - Misfire On Cylinder 2 / Code P0302
I have a 2010 accent GL manual sedan. It has 104,962 KM on it, the warranty expired December 18, 2015. Since February this car has become a frustrating money pit. Being in the dealership constantly for repairs, then within a week something else 'happens' and back it goes. Spent almost $5000 in 4 months on repairs. Decided that's enough and will do majority of repairs myself.
Yesterday while drive on the highway I had a sudden loss of power and a check engine light came on. My scanner which has become a standard item in my glove box indicated a misfire on cylinder 2 - P0302. I limped the car home, in 3rd gear I was having a hard time staying above 2000rpm at 60km/h. at lights I had to use hand brake so I could keep my foot on accelerator, revs were dropping below 300.
Today I replaced all the plugs (all 4 were still in good or better condition, #2 showed signs of a slightly rich burn and #3 a slightly lean burn), replaced all coil boots (no cracks, no burns, and still pliable), removed and cleaned all the injectors. Error code P0302 persists.
Accent LC (2000-05) :: Misfire On Cylinder 4 After Warming Up Only In Idle
2004 Hyundai Accent has is misfiring, after warming up, only in idle. This only happens after about 30 seconds in idle. Could it not be getting enough gas? This being said I was getting misfire on 3 as well but that would happen all the time and cause the entire car to shake. This problem is now fixed and only #4 is causing me problems.
View 2 RepliesAccent LC (2000-05) :: 2002 1.6L - Multiple Cylinder Misfire
Car threw a multiple cylinder misfire, changed plugs, wires, and then coil packs. Code keeps coming back.
View 12 RepliesSilverado :: 2000 - Code Saying Misfire On Cylinder 8
So I have A 2000 Chevy and i keep getting a code saying i have a misfire on cylinder 8. i have replaced the spark plug, i have replaced the coil. this code is still showing up. what else could this be?
View 2 RepliesAccent LC (2000-05) :: CEL Came On / Cylinder 4 Misfire - Exhaust Started Sounding Loud
I just bought a 03 accent the same day i bought it the CEL came on got it read and it was cylinder 4 misfire. took it to the garage the dealer i bought it from takes it to he said there was a little water around the boot in that weird little channel area under the cover he said he cleaned it up dried all out then reset the code and it was good, for a little about 2 weeks later it comes on again i get it read and it says cy 4 misfire again but also P0133 (o2 sensor bank 1 sensor 1) and i cannot remember exactly but i think the CEL came on after the exhaust started sounding loud, like it has one of those ricer mufflers on it.
Well I jacked up the car today and looked the only thing i saw was after the first cat right before the braided flex pipe there is this weird "shield" looking piece on the underside of the exhaust pipe dunno if its really supposed to be there or what it is for but from somewhere under that piece i can see exhaust coming out(its cold right now) also the flex piece is kinda blackened like its had exhaust fumes blowing on it for a while. i cant imagine why this would be a normal thing but i have never worked on hyunda before. i am thinking if there is some sort of "leak" there that is why the o2 code is showing. i am stumped, esp on the cy 4 misfire all sparks and wires look good i pulled each wire with it running and it bogs down til i plug it back in.
Accent LC (2000-05) :: Cylinder 3 Misfire / Massive Hesitation Under Heavy Throttle
I've got a 2000 accent 1.5, and I keep getting a code for a cylinder 3 misfire, when I change the spark plugs, it runs great for about 50 miles or so, then back to square one again. I just changed the coil pack the other day and there doesn't seem to be much of a difference. It has massive hesitation under heavy throttle, and the check engine light begins to blink if it sits and idles for too long. I've scanned it multiple times and it's always been cylinder 3, so it's definitely set on that one... I'm about stumped on what this could be. Also, the previous owner said that after a hot day of driving, the ECU fuse under the hood will blow out, what could cause either one of these things?
View 40 RepliesAccent LC (2000-05) :: Cylinder Misfire / Rough Idle Then 2001 GS Dies
I've recently purchased an 01 accent GS and I've replaced the timing belt, water pump, and spark plugs. Ive also got no cold air, and original struts with 119k on the vehicle. Those are the least of my worries now as my car loves quitting out at idle; and it does not get any better hot or cold. One of the plugs was completely black when it was taken out (not by me: mechanic work) so that's when they mentioned a cylinder misfire. they wanted an additional 100 to figure out what that could be attributed to on top of the 550 for the work mentioned above! I am now next to broke and want to see if I can trouble shoot some of the causes myself. I am thinking Plug wires, crankshaft/camshaft position sensors (if there are 2 dif ones?) MAF sensor, o2 sensor, injectors, and fuel filter. My understanding is that the coil pack controls 2 cylinders at a time and I just have 1 bad cylinder...I need to figure out where to start as I have no codes to work off of. also, I don't know how to assess resistance with an ohm meter.
View 12 RepliesGrand AM :: 2000 GT 3.4 Keeps Throwing Code P304 - Cylinder 4 Misfire At Idle
2000 Grand Am GT with 3.4 and 150,000 miles. Car keeps throwing code P304 - cylinder 4 misfire. The main issue is the light and needing to pass emissions test. It has just recently had new plugs, wires, and injector #4.
The fuel pressure regulator was replaced about 3 years ago because it was leaking fuel, enough to smell while driving the car with windows rolled down. Shortly after the fpr was replaced, the acceleration problem seems to have started, either by coincidence, or improper installation. The light/error has been occurring for quite some time, about the past year or two. About a year ago, the car was also throwing a random misfire code. I am not positive if both codes were being thrown at the same time, and when exactly the P304 started.
The crank (or cam) sensor was replaced and worked with the issue for a short while (removed codes/light for maybe a few months?) Before the sensor was replaced, the car would stumble at very slow speeds, 0-10 mph. Also replaced Idle Air Control valve last year. The car would sometimes surge on semi warm starts (not cold, not 190-200) between 500-1000 rpms. The surge would be worse when I had the blower running or the rear defrost on, down to 200 rpms at times.
Currently, the car runs perfectly fine for me, except when trying to accelerate on highway ramps. Its firing somewhat when you step on the pedal, but lags and takes longer than normal to accelerate up to speed for merging with traffic. Drove the car after new injection and said it runs fine while driving, but the misfire seems to be mostly or only occurring at idle.
Golf IV / Jetta IV :: 2000 - Cylinder 2 Misfire / Pending Code P0302
2000 Jetta 2.0 cylinder 2 misfire. Replaced plugs and wires. No check engine light but code is pending and there's still a misfire. Need to smog
Replace coil pack?
Swap fuel injectors and recheck?
Ford Excursion :: 2000 V10 - Rough Idle - P0304 Code / Cylinder 4 Misfire
I recently bought a 00 Excursion v10 2wd everything looked right no major problems. I noticed it has a rough idle and i thought it could be the EGR i went under the hood and there's no EGR in sight. I plugged the OBD reader to see if it would give any codes since the there was no check engine light on and wanted wanted to make sure it worked, It showed a P0304 code its Cyl4 misfire i checked plugs/coils and i noticed there's a little insert inside Cyl4 plugs hole in the head that it has the plug screwed on. I decided to change all the plugs and the coils and i still have the rough idle and code i can hear a ticking noise around the engine in the passenger side.
View 7 RepliesTacoma :: 2000 V6 Check Engine Light Code P300 / P306 - Cylinder 3 And 6 Misfire
2000 Tacoma v6 has has always ran good, but has check engine light code P300 & P306. cly 3 & cly 6 missfire, lean bank 1. Vacuum test showed no problems.
I've changed plugs & wires, switched coils around cleaned mass air flow sensor, checked timing. Ran Seafoam through intake, and gas tank. Check engine light went out for about three miles, then came back on. What else can I do to keep that blinking check engine light off?