Intrepid :: 2001 SE - Misfire In Cylinder 4 (Code P0304)
Have '01 SE. yesterday I got a misfire in cylinder 4 (code P0304) the service light blinked on and off 3 to 4 times than stayed solid. changed plugs and boots about 1 to 2 months ago, didn't change coils and they r not in the best shape but didn't have money to replace at time. So I replaced the coil for #4 and it still runs rough with code, plug has some ware but looks fine.
View 1 RepliesS-10 :: 98 Chevy ODB Error Code P0304 / Cylinder 4 Misfire
I left my chevy s-10 truck sitting over the christmas (23/24/25) and it was really cold outside and when i got back i started getting a P0304 (Cylinder 4 Misfire). I replaced the spark plugs and spark plug wires. May be the cold would cause this to happen? I think I've noticed the trucks fuels efficiency drop over the past month). May be the fuel injector(s)? Is the s-10 TBI or does it have fuel injectors for each cylinder?
View 8 RepliesPrius (2010-12) :: Code P0304 Misfire On Cylinder 4
Well, I have a big problem on prius 3, the problem is that it has a big and I mean a big body shake when I decelerate above 30 mph or slowly accelerate above 30 to 50-70 mph, when I fully accelerate, the body shake disappears. When the body shake occurs MIL comes blinking and DTC P0304 comes but not always, but the shake is only when the coolant is hot.
On the other hand, if the MIL is not on with the tester it can be seen that the cylinder 4 has misfire margin, only cylinder 4, every time. Now what I have done is to exchange the injectors, problem remains on cyl4.
-replaced the coils, problem remains on cyl4,
-clean the EGR, problem remains on cyl4,
-opened the engine to see the valves, cylinders, pistons, exchanged the ring set,problem remains on cyl 4,
Replaced the wheels, the problem is still there, now I want to replace the drive shafts.
Ford - Escape :: 2001 - Misfire On Cylinder 4 / P0304 Code
I know I can fix this problem, but my question is which cylinder is #4? I don't see it marked on the engine. The counter guys at both my local parts supply stores (whose initials are A and O) can't even look it up for me. If #4 is on the front of the engine, then it's an easy fix. If it's on the backside, then the intake manifold has to come off to get to the plugs and coil packs. It's a bit more labor. I can do it, but I'd rather not have to.
View 1 RepliesSilverado :: 2003 - Intermittent CEL Code P0304 / Misfire On Cylinder 4
My 2003 Silverado 5.3 has an intermittent CEL. I plugged in the reader and found code P0304, misfire #4 cylinder. I changed the coil, swapped the spark plug and wire from #2 cylinder to see if the code would follow. Nope, didn't follow. I swapped the injector also, same results. My daughter decided to borrow the truck and drove it so low on fuel that the low fuel light came on in the drive way. I added about 4 gallons of fuel and now the light went off. I started the engine after a jump start, and the engine really runs rough and now won't stay running. I am thinking that the fuel filter is probably needing changed because of how low the fuel.
I haven't checked the fuel pressure yet and will do that today. Now, what really puzzles me is the intermittent part. Sometimes it will run with no problem, but then the CEL will come on and the fun begins. The Chevrolet dealer says it's caused by the valves turning in the head and when it reaches a certain spot, it detects the misfiring #4 cylinder resulting in the CEL. If I pull in the driveway with the engine missing, go back out in a short time, start the engine and it runs fine. Same thing if it's running fine and I can start it and the CEL blinks and it begins missing, but may stop and run fine. I am stumped and not so sure about the turning valves.
Grand Prix :: 1997 - Code P0304 - Misfire Only On Cylinder 4 Frequently
1997 Grand Prix 3.8 N/A 181,000 ... I have been getting a misfire only on cylinder 4 which has become more frequent. It "only" happens after the car has warmed up and I turn it off for a few minutes, for instance going in to pay for gas. When I start, it immediately starts to miss but as soon as I hit the accelerator it evens out and runs great, every time. I replaced plugs and wires two years ago with stock.
Upper and lower intake manifold gaskets were replaced around 110,000. All three coil packs have been replaced with original GM packs. I replaced my EGR valve last year due to the original was sticking. My throttle body was cleaned about four years ago. I've seafoamed through brake booster and the rest in gas tank.
I'm stumped that it corrects itself right away by giving it gas. The SES light always come on but goes off on it's own after a few cycles.
Chrysler - Ptcruiser :: P0304 Error Code - Cylinder Number Four Misfire
2006 PT Cruiser Touring Ed. The engine light came on 2 days ago, had it looked at today and the error code p0304 "cylinder number four misfire" was diagnosed. What causes that and what would need to be done to fix that problem?
View 9 RepliesFord/Mustang :: 1997 - Getting Error Code P0304 / Cylinder 4 Misfire
1997 Ford Mustang 4.6L EFI engine with 67K miles. The engine is actually now in a Factory Five Roadster. It sat on a stand for 5 years but runs well now with the exception of the code. I keep getting a code P0304 (cylinder 4 misfire) and I've checked the plug - the code seems accurate; it is misfiring.
Things I've tried:
1)swapped plugs,
2)this is a dual coil engine so I've swapped coils,
3)the #4 plug is the longest sparkplug wire so I've gotten high-performance wires,
4)heavily grounded the AL head,
5)put dielectric grease on the plug,
Still, ONLY cylinder 4 gives the misfire.
Nissan - Sentra :: Check Engine Light Came On With P0304 Cylinder 4 Misfire Code
(This is a continuation of a previous thread: [URL] ..... )
I have a 2005 Nissan Sentra with 75,000 miles on it. Several months ago (see above link) the check engine light came on with a P0304 cylinder 4 misfire code. The only symptom appears to be a rough idle/shaking every 3rd or 4th start for the first 10-15 seconds, but runs smoothly afterwards. My mechanic replaced all my spark plugs (I had new plugs put it at 50,000 miles for the same issue) of which the one from cylinder 4 was worn down much more than the rest. The problem persisted so they replaced my fuel pump and fuel filter and switched the spark coils from cylinder 4 to a different cylinder, but the code still read cylinder 4 so it wasn't the coil. That was back in October.
I took my car back in last week for the same problem and without starting my car (because the problem is worst on the first start) they pushed my car into the bay and did a smoke test, no leaks in the fuel lines. Then they checked the cylinder and said that there was "excess" fuel in the cylinder and replaced the fuel injector. Then after ~3 days the check engine came back on with the same P0304 misfire code. Previous repairs/diagnostics rule out spark plugs, coils, fuel pressure, and injectors.
Ford Excursion :: 2000 V10 - Rough Idle - P0304 Code / Cylinder 4 Misfire
I recently bought a 00 Excursion v10 2wd everything looked right no major problems. I noticed it has a rough idle and i thought it could be the EGR i went under the hood and there's no EGR in sight. I plugged the OBD reader to see if it would give any codes since the there was no check engine light on and wanted wanted to make sure it worked, It showed a P0304 code its Cyl4 misfire i checked plugs/coils and i noticed there's a little insert inside Cyl4 plugs hole in the head that it has the plug screwed on. I decided to change all the plugs and the coils and i still have the rough idle and code i can hear a ticking noise around the engine in the passenger side.
View 7 RepliesFord Excursion :: Code P0304 Cylinder 4 Misfire - Broken Rocker Mount
6.0 .... Have a code Po3o4 Cyl 4 misfire. I pulled the valve cover to remove the injector and found the right half of the rocker mount and rocker arm laying in the head. What may have happened?
View 5 RepliesGolf IV / Jetta IV :: Cylinder 2 And 3 Misfire - Code P0411
Alright so my car is popping up 4 codes.
P0411 - Secondary Air Injection System Incorrect Flow Detected
P0300 - Random/Multiple Cylinder Misfire Detected
P0302 - Cylinder 2 Misfire Detected
P0303 - Cylinder 3 Misfire Detected
Vehicle: 1999.5 VW Jetta MK4 2.0L GLS (AEG)
The P0411 code I have had for a while now and I been lacking to fix it. I pretty sure I can get this fixed but it doesn't cause problems so I haven't paid to much attention to it. Anyways, the other day I noticed a puddle of coolant under my car so after checking it out, the water pump was leaking so I bought a new one and replaced the old one. However, during the replacement process I had to remove the timing belt and I accidentally turned the top pulley about 1 notch and didn't notice at the time. After putting everything back on, I turned my car on and the engine sound a bit weak so I ran for about 10 minutes around a couple blocks.
I instantly noticed that the car had no power and it took me a long time to speed up. When I got back, I plugged in my scanner and I only had the same P0411 code and nothing else. After carefully reviewing the camera I had recording during the water pump replacement, I notice I had turned the top pulley a bit so I went ahead and removed the timing belt, readjusted it, and it worked! I was excited that the car was working fine again. Soon after, I headed out to take a drive and noticed after 60MPH the car didn't have much power. The car still accelerates after 60MPH, but extremely slow. As soon as I arrived back home, I plugged in my scanner and that is where I seen the 4 codes. Now my question is what could have caused this? Could I have damaged something when I ran my car with the incorrect timing?
Things I have done so far:
-I checked to see if I left anything unplugged.
-I checked for any vacuum leaks
-I checked my oxygen sensors so see if I was running rich/lean
Things I will do after work today:
-Check the spark plugs
-Check spark plug cable for damage
Golf IV / Jetta IV :: 2001 1.8T - Cylinder Misfire Code
I recently changed my spark plugs + coil packs in my 01 1.8T because it read a couple cylinder misfire codes. Drove it for a few days out of curiosity plugged the code reader in again and it's still reading misfire codes. What could the issue be still?
View 6 RepliesGolf IV / Jetta IV :: Catalytic Code / Cylinder 3 Misfire P0303
I own a BMW not a VW! My 19yr old daughter purchased her first car a few months ago, an '03 Jetta 2.0L with approx. 170,xxx miles. Just after she got it we pulled a P0420 code, but it ran fine so we haven't worried too much about it. I've cleared that code and after about 2 weeks it will come back. Last week it started to have some issues with rough idle, stumbling/hesitation. I pulled the codes yesterday an in addition to the catalytic code is a cylinder #3 misfire P0303. I thinking the 2 codes are not related. I'm assuming the typical things to look for on the misfire are coil, wire, plug? Looks like the coil on this engine is a combined unit so no switching coil packs to see if the miss follows a bad coil pack.
View 4 RepliesGolf IV / Jetta IV :: CEL On With Camshaft Position Sensor Code And Misfire On Cylinder 3
She is a 1999.5 Golf 2.0 (although, she just has a rabbit symbol on the hatch, is she a Rabbit or did someone remove the Golf badge?) I just bought the car, with less than 160,000 miles. The dome lights work sometimes, Door Ding works intermittently as well, but sometimes will "glitch" in other words it will be making the sound but it kind of stutters? Odd? The horn sometimes works, however it is very silent? Check engine light is on with a camshaft position sensor code and miss on cylinder 3. Someone told me to replace the "109 relay"... could this be the problem or is this the CCM?
View 5 RepliesGolf IV / Jetta IV :: 2000 - Cylinder 2 Misfire / Pending Code P0302
2000 Jetta 2.0 cylinder 2 misfire. Replaced plugs and wires. No check engine light but code is pending and there's still a misfire. Need to smog
Replace coil pack?
Swap fuel injectors and recheck?
Golf IV / Jetta IV :: Loss Of Power And Hesitation / CEL Code For Misfire On Cylinder 1 And 5
When i got my 2000 jetta vr6 it has a CEL for misfires. Searched this board and google already. Im thinking injectors (havent checked yet) I noticed something weird the other day. At a light i get the CEL flashing. Then after a bit it will come on and stay on. I plugged in my generic reader and deleted the codes. When the CEL is on I get loss of power and hesitation. When its deleted the car runs better. I get my power back. I looked in the coolant tank and see no bubbles. Could this be the ECM? Im still going to get injectors but want to buy the gasket and anything else I am going to need to put it back together. I already cleaned the MAF, replaced some vac lines, coil pack, wires and checked plugs (gapped at .28) ...
View 4 RepliesFord F-150 - 1997-2003 :: CEL Codes P0304 / P0456 / P0171 - Misfire On Cylinder 4
So, my 2003 F150 4.6 that I just put back on the road after a four month break is running like crap. I took it off the road for the winter because it was missing (no codes) and didn't feel like dealing with it then but after running it for a day the CEL comes on. It shows the following:
P0304 - hoping it is a coil pack
P0456 - pending. Gas cap?
P0171 - pending. One bank too lean?
Does the 171 code possibly have to do with the misfire in Cylinder 4? I know it is impossible to tell yet but am hoping there is a potential connection.
Before I parked it in January, it was running a bit rough and stumbled on acceleration but never would show a code. Now all this. Going to change the coil first, tighten the gas cap, check for leaks and see what happens but is there anything common on these trucks that I should also be looking at?
Camry :: 2002 - P0304 Code / Misfire Occurring
We just bought a 2002 Camry with 72,000 miles 2 months ago. It now has 74,000 and while on vacation the CEL came on. I took it to a mechanic who got the code P-0304 off the computer. He swapped the number 4 ign. coil pack with the number 3 cylinder. The CEL light went off and I was able to drive the 300 miles home. The next day the CEL started again, but this time it's flashing. I changed the spark plug, it looked good, and still have the CEL on with the P-0304 code.
I've inspected the wiring to the number 4 ign. coil pack and it looks good. I'm thinking the next thing would be the fuel injector.
The car runs great, you'd never know by driving it that there is a misfire occurring. If it's not the wiring or fuel injector what should I check for next?