Ford F-150 (2004-2008) :: 2006 Truck Cranks But Does Not Start
I just went out to move my truck to take out garbage and it cranks but doesn't start. It is 4.6L 4WD. I sprayed ether in intake no change. Checked all fuses all good. It has been raining pretty hard the last 3 days and it has been sitting in rain all 3 days. I checked for codes with a simple code scanner no codes. But the code scanner I used is not able to do KOEO or KOER tests. I know it needs new plugs but it has never sputtered or died on me. Has slight misfire but not engine stopping. I havnt had any check engine lights or problems before.
View 3 RepliesFord F-150 (2004-2008) :: 2006 - Intermittent No Start Condition And No OBD Codes
2006 F150 4.2 fuel issue? I get an intermitent no start condition and no obd codes. Then I discover that it really isn't intermittent, it only occurs after I have been running the engine. It will not start for at least 5-10 minutes after I have driven a few miles and shut the engine off. So if I wait 5-10 minutes then she starts and runs just fine. I played with this in the driveway to recreate this condition so I could determine if I had a spark or fuel issue (I have spark during no start). I found that 50% of the time I could start it right back up immediately after I shut the engine off. But if I shut it off right away again, then I got the no start condition again and have to wait another 5-10 minutes.
Now with cold engine I can start the motor over and over. To fix this I read forum after forum, which led me to decide that I had a fuel pump driver problem (module) located on back axle under spare tire. I replaced this and restarted the engine many times. The problem seemed to be gone but this only lasted about 30 minutes. Then it would not start at all and still no codes. I plugged my old module back in and the truck fired right up. So I decided I needed to (flash) pcm for new part but that changes nothing. Still no start with new module and runs with old module. I also replaced relay in fuse panel.
Ford F-150 (2004-2008) :: Cranks But Won't Start?
Ok so... have an 04 that has more issues than Playboy magazine... any DIY tips or tricks...
I dont have an original key but the key I have has worked before. Motor cranks but wont turn over. Have tried the battery unhook thing, didnt work.
Ford F-150 (2004-2008) :: Cranks But Does Not Start
Truck has been running perfect and is my daily driver. Went grocery shopping with the wife and made two stops and drove it home. Parked in the driveway. No hint of any issues but when I went out a couple of hours later we went to head out to dinner and it cranks and doesnt start. Nothing out of the ordinary anywhere. No check engines lights, no theft lights flashing, nothing to indicate an issue. Engine sounds perfectly normal cranking, I can hear the fuel pump when I turn the key. I cleaned the battery terminals today because they had some corrosion and I checked all of the fuses that have anything to do with fuel or fire and nothing was blown.
I also went and bought a Fuel Pump Drive Module and installed it and still nothing so I took it back.This is a pretty pampered truck, not a torn up beater. What else I should check? Will probably town it to a shop tomorrow if I dont have anything else to try but I am at a loss at this point. I tried to listen with a stethoscope and I dont hear the injectors firing or the COP's. Oh I also shot it with starting fluid and nothing happened so I dont believe its fuel related. I think something is keeping it from firing the COP's or the injectors arent firing. But what could it be? Nothing happened to the truck last time I drove it. Oh I did check the fuel pump cutoff button as well. Nothing there either.
Ford F-150 (2004-2008) :: 2005 Cranks But Will Not Start
My 2005 cranks but will not start. I spray starter fluid in throttle body and it will start but won't stay running. I've replaced the fuel pump and the fuel sender unit which is located under the spare tire. After I replaced the fuel sender unit It started and ran for about 30 seconds. It quit when the fuel line popped off the fuel pump and pushed gas all over the ground. I secured the gas line back on and now it won't start again unless I use starting fluid.
View 3 RepliesFord F-150 (2004-2008) :: 2006 FX4 5.4L Takes About 10 Cranks Before Firing Up
Recently my F150 has had issues starting in the mornings. It is in an insulated garage. It takes about 10 cranks before it fires. Then it struggles to run like its not getting fuel for a second or two, then rpm's jump to 1200 and has a slight miss for another second or two, then it smooths out and is fine. Leaving my driveway it will have a miss around 2000rpm for about two seconds then the truck will run perfect the rest of the day. It can sit outside in the cold for 10 hours while i am at work and will fire right up and run great. The issues only happens in the morning.
All the plugs were changed about 6 months ago. Fuel pump and fuel pump drive module were changed about 3 weeks ago. The check engine light has come on twice. The first time I didn't have access to a code reader and since the truck started right away and then died instantly i figured that was why the light came on, so i disconnected the battery and re-connected it. Light didn't come back on for a week. Second time code was for misfire on cylinder 5. I am changing the fuel filter this week. If that doesn't work i was gonna change the #5 coil.
Ford Wiring/Electrical :: 2002 F350 V10 Won't Start / Cranks Slowly Like Battery Is Dead
I have a 02 f350 v10 with a starting problem. Sometimes it will crank but really slowly almost like the battery is dead, but its not! bench tested the battery and actually just bought another new one. And with the same result. I tested the relay that's on the firewall in between the starter and the battery and it checked out, i also bought a new relay and i want to put it in except I haven't figured out which wire goes to the coil and which one goes to the ignition. the battery and starter poles are marked and easy to follow ..
Also last month I changed the starter but I'm starting to get desperate and i think I'm going to take it off and have it bench tested as well. I'm just really at a loss in which direction to go. The truck on the outside really looks good but living in the northeast the frame and probably most of the outside grounds are toast and I've been renewing or just placing them as I come across them. Before i forget i tried jumping the starter directly from the battery with cables and got the same result. it would crank but too slow to actually turn over.. Sometimes my radio and ignition lights will sometimes come on without the key in the ignition..
Ford Super Duty (1999-2016) :: 2008 - Code P0201 For Injector Cylinder 1
This is my first Ford. 2008 6.4L 165K miles full delete. Bought this truck at auction already deleted. Found an H&S pod mount instructions in glove box and so I am thinking it had their software loaded to it. I knew it had sat a while, but did fire up no problems. I have already replaced all fuel filters (actually learned I did them backwards, and did not cycle the key) and had no issues re-starting! I've put at minimum 30 minutes but no more than 1 hour run time on this thing post filter change. I'll get to the gritty. . This all started when I pulled a P0201 code for Injector Cylinder 1.
I pulled the valve cover to troubleshoot the injector, following a post I saw few days back. All checked out fine with the #1 compared with #3, and so I cracked loose the fuel line going to the #1 injector. The line was dry and thought it was strange, but I had changed out the FRP sensor prior and remember no fuel came out then either. Before pulling into the garage the truck was running rough but thought this was due to a P0193 code FRP pressure Circuit High (again). So I put the line back on, tightened the darn out of it.
I know these things see a 26K psi at times. I depressed the Schrader valve at the fuel cooler and got only a minute bit of air out. I didn't think this was enough, and so I took the Schrader valve out, hard lesson learned. I re-installed it and I fashioned a homemade tool connected the Schrader valve with a ball valve to cycle the key-on and purge out the air. I have ran the batteries down cranking trying to get it to fire. I am now getting no more air bubbles.
Had to get another diesel pickup to keep juice on the batteries. After 3 hours, 6 hours total, cannot get this thing to fire off! Am I missing something simple? Everything I have done to this point before reading the forum I have done backwards and all has been fine! Could it be that just now I am seeing the effect of the filter change being done backwards? On my scanner I can see the live FRP, it has to be the cmd, it is sitting at 29Kpsi. At this point should I re-pull the filters and start fresh?
Accent MC (2006-11) :: 2008 Cranks And Won't Start Up
My 2008 Accent has a manual trans and 4-Cyl, 1.6L. It had some bad fuel 4 weeks ago, and filled the tank with 97 to clean it back up.
I was driving and came to a stop sign - the server stopped and wouldn't start up again. I was worried about the fuel pump, and ended up replacing the whole thing (under the passenger seat).
I have tested the following:
- When cranked, the bottom of the spark plugs are wet (so gas is getting to the plugs)
- When plugs are pulled out, they spark against the block (so spark should be getting to the cylinder).
The car still doesn't start, and the cranking sounds 'off'. I can't exactly describe what's wrong, but I've had it for six years and it doesn't sound right.
Ford F-150 (2004-2008) :: 2005 F350 Cranks But No Start And No Spark
Brought a 2006 f350 6.0 from the action and knowing it was damaged from the frame, i went ahead and brought a another f350 6.0 2005 from someone around town, the last owner is calming the truck was stole, and most of the engine was stole, and the windows where damage. ( I just wanted to buy the truck for the body so i can transfer the engine to this one! ) but instead of switching the engine, me and my dad went ahead and only put the missing parts back onto the engine....
I can tell the last owner wasn't telling the truth, and me and my dad where thinking the last owner made up his own story about the truck being stole !! I did a vin check and noting came up about having a bad history!!!!!!!!! I'm thinking something went bad in the truck, and the last owner did his own fault story... Anyways!!!
we finally put everything back in place, and the truck cranks, but does NOT start!! and also has no spark. sometimes it sounds like it does wanna start!! we check the fuel, and wires, oil, fuel filer! everything good, but the truck has no spark, and where not sure if thats the problem. and also switch out the Crank sensor. Still no luck!!
And also there is smoke when we crank. battery are good too, and even left the truck 28 hours on the wire to head up the engine!!
Sonata NF (2006-10) :: 2008 2.4L Engine Cranks But Won't Start
I have an 08 2.4L Sonata with 95000mi. When turning the ignition it will crank and sound like its about to start but won't. I was able to get it to start by pushing the gas pedal a bit when it sounds like it wanted to start. Once started, it ran rough and would stall unless I revved it above 1500 RPM. Still sounded like it occasionally miss fired.
I kept it revved until it reached normal operating temp. When I took my foot slowly off the gas, rpm dropped to about 500-600 and it seemed to pulse . I think engine was raising throttle to keep from stalling. It stalls if I try to put in gear without pressing on gas to raise throttle.
The spark plugs were changed at about 70K mikes. I have not read any codes as the car is stuck in the driveway. Could it be a vacuum leak? I know the Entourages have air intake hose leaks that cause rough idle but with a 6 cyl it still runs. Fuel pump problem?
Ford F-150 (2004-2008) :: Truck Cranks Great With Full Power But Won't Start
My 04 f150 has been sitting upwards in my drive way for a month now won't start cranks great with full power..
View 1 RepliesStarting - Chevrolet - Capriceclassic :: 1994 - Engine Cranks Very Slowly Almost Does Not Start
1994 Caprice Classic (350 cid LT1)... Engine cranks very slowly, almost doesn't start, sometimes starter disengages/re-engages. 1year ago mechanic checked batty, alternator and starter, all ok. I had starter replaced as it seemed the most likely cause. Eventually got better but now is worse again. Also notice a lot of movement on the dash voltmeter needle, sometimes high, sometimes low, turn signal moves the needle. Ive spent hundreds of dollars on troubleshooting and the new starter. What could be causing this?
View 4 RepliesFord F-150 (2004-2008) :: Turns Over But Won't Start - No Codes
So, my 2004 FX ran perfect as always when I parked it last night but this morning it just will not start. It turns over like a SOB but won't catch (Installed a new Optima Red Top about a month ago). Tried my OBDII but it's showing as "fail" or "no codes".....I tried testing it several times. I've never had ANY problems with it starting.
View 2 RepliesFord F-150 (2004-2008) :: 2006 - Rough Idle With Many Codes
I just received a 06 F150xl with a 5.4 triton and idles rough with the following codes! p0357 p0012 p0340 p0344 p0351 p0352 p0356 p0358 p0357 p0102 p0113 p0353 p0354 p0355 It's amazing the truck even runs and with no light on but it will accelerate. someone mentioned to clear the codes and drive it 50miles or so and read them again.
View 9 RepliesFord F-150 (2004-2008) :: 2006 V6 - Got Codes P0171 And P0302
I'm lost. Got P0171 and P0302 ... 2006 4.2 V6 5-speed 220K ... Got bad miss ...
Compression check was good.
Replaced plugs.
Replaced wires.
Replaced coil pack.
Cleaned MAF
Miss remains. What do I do next?
Ford F-150 (2004-2008) :: Occasional Hard Start / Engine Cranks Strong But Fails To Catch And Then Sputters
My truck's been having an occasional hard start, meaning the engine cranks strong but it fails to catch and then sputters. The 2nd start attempt usually fires up with no issues and then runs perfectly otherwise.
MPG's haven't changed, fuel filter was changed 15K ago. Air filter is clean. Plugs were changed about 10K ago. I always use Shell/Chevron gas. MAF sensor looked clean when I took it out so I didn't do anything to it.
This is starting to happen more frequently, maybe once every few weeks and I get a feeling it's the start of something. I've found myself waiting a few seconds for the fuel pressure gauge to come up before turning the key to start reliably. In the past, I could simply flick the key and it fires up the first time.
I see posts talking about the fuel pump module above the spare tire. What are symptoms of that going bad? Any pending codes that might be stored?
I'm about to get myself a scanner since I need one sooner or later. Which specific PID's to check while debugging this?
Ford F-150 (2004-2008) :: 2006 - Intermittent Misfire But Not Throwing Any Codes
I have a 2006 Lincoln Mark LT that seems to have an intermittent misfire. The truck is not throwing any codes either.
View 6 RepliesFord F-150 (2004-2008) :: Start / Run Rough For A Second Then Die - Codes P0172 And P0175
First off its a 2006 F150 king ranch with the intercooled roush kit and roush tune. Last couple weeks its progressed from a slight stumble on start up, to now after its been off for a few hours it may start and run rough for a second, or, it may start then die, and then have to crank for at least 5 seconds before it starts. After it starts it seems to run fine. I've thrown the P0172 and P0175 code a few times. I downloaded the torque android app and did some data logging. Can you learn anything from the long term fuel trim?
View 9 Replies