Ford F-150 (2004-2008) :: 2006 - Intermittent Misfire But Not Throwing Any Codes
I have a 2006 Lincoln Mark LT that seems to have an intermittent misfire. The truck is not throwing any codes either.
View 6 RepliesAzera TG (2006-11) :: Intermittent No Start Condition?
I own a 2006 Azera Limited. I've been experiencing intermittent problems starting it. It cranks fine but will not start? The battery is new.
View 1 RepliesFord F-150 (2004-2008) :: 2006 5.4L - Cranks Slowly But Won't Start - Codes P0201 - 208
Bought a truck from a guy the other day. Long story, but he was a con artist. Told me the battery was dead from cranking it, he couldn't hear the fuel pump so he thinks it needs a new one. Got it home, checked fpdm, it was unplugged. Plugged it in fp running now. Charged battery. Cranks slowly won't start. Appears the engine has been changed. Have codes P0201-208, all injector codes. Cranking it over reminds me of an older distributor type engine that if off its timing. But also of cranking with a low battery. There's a new starter on it already. I'm going to pull the converter bolts on the weekend to see if they may have bound the torque when they installed the engine. Injector codes?
View 4 RepliesFord F-150 - 1997-2003 :: 1999 - Intermittent No Start Condition
The Truck...
1999 F-150 Supercab
170K miles
4.6 Litre
Automatic Trans
The Problem... About every other day, I try to start the truck, and it doesn't fire at all. It cranks fine, everything seems right, but no start.
What I've done...
Replaced Fuel Pump Relay.. (no luck)
Sprayed Starting Fluid In and Cranked... It Fires On Fluid.
Other info...
This problem never lasts long, and the problem mysteriously fixes itself after no more than an hour.
This problem has occurred both when the truck was warm and completely cold.
Sebring - Chrysler :: Intermittent No Crank Or Start Condition
2008 Chrysler Sebring V6 hardtop convertible ... Intermittent no crank / no start condition – when turning key to start position, either you get nothing as if there is no battery connected and or a slight click as if the solenoid was trying to engage. The pattern can be nothing, nothing, nothing, click, click, nothing, startup or any combination of clicks or nothing, always resulting with a startup. Sometimes it will only be 3-4 attempts, other times 15-20. This occurs anywhere from every 15-20 starts to driving 2,000 miles from NH to FL without one failure.Completely random occurrence – no pattern can be seen – has been ongoing since September 2015 to now March 2016.
I have tried moving the shift lever and the steering wheel while it occurs, no change.Facts – battery was replaced 2-3 years agoAfter the first occurrence I yanked the battery, cleaned the terminals as well as the terminals under the hood. Over the next couple of months brought it to the dealer who could find no codes and of course it did not fail while they had it so they did nothing. In December I appealed to the service manager to replace the starter as I thought is sounded like a bad spot on the armature. He did so and also had the WIN module replaced. No issues until I was in FL weeks later. Here the dealer has replaced the PTC and TIPM modules and installed a redundant ground wire. The problem is still occurring. I’m down to under 400 miles on my 100k bumper to bumper warranty?
Ford 6.0L Power Stroke Diesel :: 2006 - No Start Condition When Hot
I've been having an intermittent problem with a no start condition when hot. It has lately gotten worse to the point that I was dead in the water for about 25 minutes while i had the hood open to allow things to cool off. I closed everything back up hit the key and it jumped to life just like it was new. I've read through the tech folder as well as several other threads regarding no starts but haven't run across anything that is pointing me in any one direction. It cranks over very strong on new interstate batts that are only 6 months old and the SGII shows sync on the FICM and I'm getting a good RPM signal showing about 160-170 cranking RPM.
Good logic power and showing 47.5 to the injectors. I'm running an atlas 40 from Ed in the FICM. I've wiggled wires and done a cursory look but I would think that if there was any chaffing that cooling off wouldn't affect it and it would be dead until fixed. Once it is running I have no problems, never let me down or quit on me while under way. Again, it is intermittent where I'll have 3 weeks or a month of no problem at all and then run into long crank times for another couple of weeks.
I've made no mods to any of the HP oil system and have no leaks that I can see, no consumption between oil changes. I'm in the middle of building a house right now and need the truck to be reliable. I'm pretty good with a wrench if I know what the problem is but I don't know where to start on this. It's an '06 model but an '05 build date on the motor.
Ford F-150 (2004-2008) :: Turns Over But Won't Start - No Codes
So, my 2004 FX ran perfect as always when I parked it last night but this morning it just will not start. It turns over like a SOB but won't catch (Installed a new Optima Red Top about a month ago). Tried my OBDII but it's showing as "fail" or "no codes".....I tried testing it several times. I've never had ANY problems with it starting.
View 2 RepliesFord F-150 (2004-2008) :: 2006 - Rough Idle With Many Codes
I just received a 06 F150xl with a 5.4 triton and idles rough with the following codes! p0357 p0012 p0340 p0344 p0351 p0352 p0356 p0358 p0357 p0102 p0113 p0353 p0354 p0355 It's amazing the truck even runs and with no light on but it will accelerate. someone mentioned to clear the codes and drive it 50miles or so and read them again.
View 9 RepliesFord F-150 (2004-2008) :: 2006 V6 - Got Codes P0171 And P0302
I'm lost. Got P0171 and P0302 ... 2006 4.2 V6 5-speed 220K ... Got bad miss ...
Compression check was good.
Replaced plugs.
Replaced wires.
Replaced coil pack.
Cleaned MAF
Miss remains. What do I do next?
Ford F-150 (2004-2008) :: 2006 V6 - Intermittent Starting - When Turn The Key Starter Will Grind Once Or Twice
I have a 2006 F150 STX auto trans with the 4.2L V6 that has been having intermittent starting problems. It has 98,000 miles on it. It will start fine 99% of the time but sometimes when I turn the key the starter will grind once or twice then it can go a few weeks with out doing it at all. Then also sometimes it will crank turning over for several seconds but wont start. Then it starts fine the rest of the time. This has happened several times but only happens once every few weeks or so. Just trying to see if it needs a new starter or if its something else. It has a new battery.
View 3 RepliesFord F-150 (2004-2008) :: Lean Condition Bank 1 And 2 / Random Misfire
2006 f-150 with a 4.6L. Its got 175k on the clock and ran like a sewing machine despite little maintenance other than oil changes. Recently it started running like crap; no power and missing so he borrowed a scanner and it was giving multiple codes. Here's what we have done so far, not necessarily in this order :
1.Checked for vac leaks with carb cleaner (this can be tough as engine runs crappy and hard to detect minor changes in rpms while your under the hood) no leaks detected yet
2. Changed the plugs, all looked good except for one which was heavily fouled and the electrode ate away mostly, I wasnt there and he doesnt remember which one but have a suspicion, more on that in a min
3. Changed most of the COPs and checked them all with a spark tester, all are firing.
4.Cleaned the MAF sensor with MAF cleaner
5. Checked back pressure on the exhaust by removing an upstream o2 sensor and holding a plastic fitting hooked to a pressure gage long enough to get a reading, about 1 lb idling to maybe 2 max when engine is reved, gage is not the best and fluctuates a 1/2 lb or so. Exhaust does not smell of rotten eggs.
6. Changed the fuel filter, it was terrible
7. Ran a bottle of Seafoam in the tank
8. Took the throttle body and egr valve off and checked for carbon stoppage, the holes in the egr were not blocked
9. checked the PVC valve and line and both elbows
7. checked the injector connectors with a noid light for signal, they all flash, checked the injectors them selves with a multimeter set for ohms, all about from 13.5-14.5. This should mean they arent fried but could they still be stopped up? They all sound like they are pumping when you listen with a mechanics stethoscope
9. Changed all 4 o2 sensors as this had never been done anyway
10. Compression check on cylinders, all within 10% of each other at about 180 lbs. When we pulled the plugs they all looked good except for # 7 which was heavily fouled ( I suspect the same on the original plugs) and again with a bad electrode, the part coming out of the porcelin. Intrestingly, this was an autolite plug, the rest were motorcraft, I hoped this was somehow just a bad plug but no change with a new MC plug
11. Changed the injector on #7
The scanner reads lean condition on banks 1 and 2 and random misfires on #4 and # 7 still. Per a troubleshooting tip online, we sprayed some carb cleaner in a small vac line coming off the manifold to induce a rich condition and the scanner showed the o2 sensors go to .900 which is what they are supposed to do per the guide. This means they are functioning correctly and a bonafide lean condition exists. I am leaning towards a vacuum leak around the plastic manifold under the aluminum one, maybe the gaskets but would like to rule out the egr valve, could it be the culprit?
I have even considered the possibility that the PCM is bad, though not likely. I have read to detect a vac leak you can hook the scanner up and spray the carb cleaner around on the manifold and lines with the scanner hooked up watching the scanner PID for the o2 sensors and when they detect the cleaner, they will hit that .800-1.0 meaning the engine sucked the cleaner in and you have found your leak. The exhaust smells rich. If it is a vac leak, you would think it should be a massive leak and not hard to detect, as crappy as the truck runs. I have searched the forums for days and exhausted about all I know to do.
Most important note: early on I suspected low fuel pressure as a possibility; with no schrader valve on the fuel rail and no easy spot to T into the system, we were scratching our heads how were gonna measure psi but the scanner reads absolute fuel rail pressure, gives about 40-43 psi. I hope the scanner is telling us what we need to know there, would prefer a mechanical gauge on the rail!
Ford F-150 (2004-2008) :: Start / Run Rough For A Second Then Die - Codes P0172 And P0175
First off its a 2006 F150 king ranch with the intercooled roush kit and roush tune. Last couple weeks its progressed from a slight stumble on start up, to now after its been off for a few hours it may start and run rough for a second, or, it may start then die, and then have to crank for at least 5 seconds before it starts. After it starts it seems to run fine. I've thrown the P0172 and P0175 code a few times. I downloaded the torque android app and did some data logging. Can you learn anything from the long term fuel trim?
View 9 RepliesFord F-150 (2004-2008) :: 2006 - Misfire - Lack Power - Stalling - O2 Codes?
I am perfectly capable of doing the repairs just short on time. the only shop in town is booked out 2 weeks, i need my truck sooner. 2006 f150 5.4v 3v 168k. I bought it with 150k and it was clean and ford maintained from the original owner. for a while it has been fluttering from time to time during acceleration. last week it started shuttering and missing around 45 trying to accel. no cel. I've read and actually fixed my freinds 08 but replacing cop and plugs. I bought motorcraft plugs and granatelli coils. friday morning it didn't want to start, cranked for a bit then locked up, as if hydrolocked.
I let it sit 5 minutes then cranked again and it fired but hesitating and missing like never before. anything passed 3k rpm it ran good no load. i had to drive it and it doesnt want to shift properly, revving way past normal shift points. smoking alot more than normal. hard to tell being 5 degrees out. finally got some codes. bank 2 sensor 1 stuck rich 4 times lean twice. Saturday i changed the oil plugs. and coils plugs were not original but were worn enough to visually see. all of the passenger plugs were a nice brown color. all of the driver side were jet black of carbon which follows the o2 cel. i reset it with my glorifed code buddy and it took a while if at all to come back. so im thinking not an o2 sensor????
It runs rough and will stall from time to time, I am to the point where i wont drive it. i will be replacing the camshaft sensors and vct solenoids tonight, and that one 2 if i have time. from what I've read phazers will cause a rough idle but once under load at least have some performance. when i accel it the rpms stall out before a shift i cant get anymore power, say wont got over 3200rpm. when chains and guides need to be replaced whats the symptoms??
Ford F-150 (2004-2008) :: Intermittent Noise Start From Water Pump When Cruising At About 2000 RPM
I got a 08 F150 with a V6. It's making a very loud and annoying noise that sounds a lot like a bad steering pump, but it's coming from the water pump. I'll be cruising at about 2000 rpm and the noise will start all of a sudden. I step on the clutch and let the rpm drop to idle, and the noise tapers off as the rpm drops and then stops completely. I bring the rpm back up, and there's no noise. There is absolutely no play in the water pump bearing, no leakage from the weep hole, no overheating.
View 2 RepliesFord Super Duty (1999-2016) :: 2006 F350 - No Start Condition After Truck Warms Up / ICP Location
Where the ICP is located on a 2006 f350? I have a no start condition after the truck warms up, everything else is fine. Started fluid works to crank, I suspect the ICP and /or Orings.
View 4 RepliesFord F-150 (2004-2008) :: 2006 - CEL Came On - Idles A Couple Of Minutes And Shuts Off - Codes P0607 / P2107
My 06 was parked about 2 months and when I first started the truck, the CEL light came on. It idles a couple of minutes and shuts off. It was running very well before it was parked. I put a code reader and the codes are P0607 and P2107.
View 1 RepliesFord F-150 (2004-2008) :: 2006 - Missing And Rough Idle - Codes P0340 / P0344 / P0345 And P0349?
I recently purchased my first Ford pickup. I bought a 2006 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 146,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run well when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around the rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
Sonata NF (2006-10) :: 2008 GLS 2.4 Liter Won't Start - Throwing Codes P2110 / P2118 And P2119
My 08 2.4l sonata gls won't start. I started it this morning to warm it up while I cleared off all the snow, it was running for about ten minutes. I turned it off and about twenty minute later went to start it and it will not catch. All the electronics are running and the engine turns over but it won't start. I replaced the battery in December, the oil was changed last week as well as the air filter. It has 93k miles on it. What could be the problem? I did go borrow a diagnostic scanner and it is throwing a P2110 P2118 and P2119 code.
View 4 RepliesCamry :: Intermittent Air Condition And Speedometer Is Not Working
I have an 08 Camry that appears to be having the problems associated with the ABS module (intermittent A/C, speedometer not working, etc.).
I've picked up a module/pump from a junkyard. Excuse my ignorance, but the module itself (black portion), does not have any fluid circulating through it? If I'm just swapping that, there is no need to bleed the ABS or perform any programming?