Ford F-150 (2004-2008) :: Gode Codes P0172 / P0300 And P0303?
My son just left. We scanned his truck and got these codes.
P0172 Bank 1 rich P0300 random misfires P0303 cylinder 3 misfires.
I used the Torque APP Pro to check these codes. I went to live readings in the Torque APP and saw some readings for Long term and Short term bank 1 Readings.
They are all "greek" to me, and I don't recall what they were, but could get those readings tomorrow.
When I have done searches combining these codes together, I see changing spark plugs. P0172 alone gets me a different train of thought. Mainly CAT issues.
Also, his cranking to start is quite long. (A lot longer than my 6.0L would ever think of cranking) At least nearly 30 seconds of cranking. We are leaning toward first just changing #3 plug.
Ford F-150 (2004-2008) :: CEL On - P0172 / P01275 / P2106 Codes But Running Fine?
so i had a litle fun in the clay today ..and now my trucks check engine lights on ..i have a code reader im running a P0172 P01275 P2106 Ive cleaned the MAF and changed my air filter...still running the three codes afterwords no trouble with turning over starts right up and drives with a normal amount of power....its a 2004 5.4L V8 ...
View 12 RepliesFord F-150 (2004-2008) :: Code P0175 Cleared Up - Hesitates On Takeoff And Slight Shake Like A Misfire
I have a 2005 F150 5.4 and I recently got a p0175 code. I've replaced the M.A.F. sensor, fuel injectors, fuel filter, new plugs, coils and checked the vac lines but I'm still getting a p0175 code. Ive reset my P.C.M. and the code stopped for 2 weeks but returned later. The truck runs fine when I erase the code but when it returns it hesitates on take off and has a slight shake like a misfire and it makes a bubbly popping sound from the exhaust. Im at a loss of what to do next! Could this be a code stuck in the P.C.M.? My mechanic thinks it may be the cam phasers!
View 5 RepliesFord F-150 (2004-2008) :: 2006 - Rough Idle With Many Codes
I just received a 06 F150xl with a 5.4 triton and idles rough with the following codes! p0357 p0012 p0340 p0344 p0351 p0352 p0356 p0358 p0357 p0102 p0113 p0353 p0354 p0355 It's amazing the truck even runs and with no light on but it will accelerate. someone mentioned to clear the codes and drive it 50miles or so and read them again.
View 9 RepliesFord F-150 (2004-2008) :: 2005 - P0172 Code Keeps Coming On
I have a 2005 F150 Fx4 5.4 that keeps throwing a p0172 code. I've replaced all spark plugs, C.O.P's, fuel injectors, Mass airflow sensor, 1 o2 sensor, checked all vac lines and there ok.
View 2 RepliesFord F-150 (2004-2008) :: Rough Idle / P0012 - Misfire Codes Associated With Bank 1 And Cylinder 3
5.4 3v. my last few weeks have not made me a fan. Here are the details:
I bought a 2008 F150 XL 5.4 3v with a cam phaser knock. Have done other timing jobs in past with no trouble so I was not too afraid to tackle this one. famous last words...opened the motor (shout out to the passenger side valve cover and its designer here) and found semi damaged roller follower on driver side. Worn cam lobe on the corresponding lobe and a loose chain on passenger side. proceeded to :
Change all timing components: phasers, chains, tensioners crank sprocket, all applicable bolts and BOTH cams as well as all lash adjusters and roller followers. most looked fine in fact all really did with a bit of wear on a few roller followers but only one bad one. engine didn't look to bad pretty clean.
Double and triple checked my timing chains and it was spot on. dark link on spot on crank, two dark links on the L and R dead on. put it back together. oh yes, changed all plugs with motorcraft ones, didn't even break one. did not change vct solenoids because I falsely assumed I could change the later easily if needed. they looked ok. screens intact etc... silly me for not realizing how kind Ford was in 2007 and later to necessitate removal of valve cover. I was reading a previous one on the how tos and assumed later models would be the same since it was the same sensor...
Cranked truck ran great. I mean perfect. sounded perfect. ran like a scalded cat. till it got to hot idle then it started doing its thing. rattle shake till you revved it. ran fine just wouldn't hot idle fine especially in reverse or under slight load. replaced driver side vct since ford only had one and I started on the easy side ordered the other one waiting for it. seemed to improve dramatically meanwhile I am driving this truck to test it. I drove it to work 50 miles each way and it ran great.
After a few trips it popped the P0420 light, seemed to run ok, cleared it watched it wouldn't come back. O2 sensor did seem to imply a bad cat on bank 1 since it seemed sensor two was mimicking sensor one and not staying stead like the other bank. still ran fine,
So I decided to check back pressure on the cat. I pulled sensor one out of bank one (really a joyously tight squeeze in there) hooked up my gauge and got 0 back pressure. revved it and all nothing. hooked sensor back up pulled truck out of shop and it commenced to running like crap. I mean bad. running worse than before I got it. Popping P0012 code continuously, and tons of misfire codes associated with bank 1 ..cyl 3 etc.. I tried swapping coils, pulled coils and checked spark with a tester and firing away looks like tons of good spark.
Now the weird part is : looks like bank one is dead. I can unhook any coil pack and/or injector and it runs the same and sounds like it is missing. if I unhook one off of bank 2 it almost dies or does. so bank 2 seems to be running fine. it will start and run but sounds like it missing sets flashing check engine light and backfires and stalls like crazy. I even second guessed my pressure gauge and unhooked exhaust manifold from pipe and it sounds even prettier when it backfires out of there but no change. I pulled cam sensors and cleaned it again and even tried swapping them since they looked identical but no change so I put them back.
Now I can only surmise that I am out of time somehow? or I have a gremlin perhaps? I like working on cars (usually) but this one is getting old. how do I verify what is wrong. if it is timing related how do I verify that now definitively once my marks moved I really cant figure out how to tell if it is in time? Since it has all new parts and they all ran beautifully till now. could it possibly be the vct solenoid doing all this? I plan on changing it when it comes in but surely it cant cause this many problems.. I unhooked it no change, and it does it at a cold idle and any rpm. really runs worse at idle but bad at any rpm.
Ford F-150 (2004-2008) :: Misfiring - Rough Idle - Got Codes P0340 / P0344 / P0345 And P0349?
I recently purchased a Ford pickup. I bought a 2004 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 200,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run good when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come to on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
Ford F-150 (2004-2008) :: 2006 - Missing And Rough Idle - Codes P0340 / P0344 / P0345 And P0349?
I recently purchased my first Ford pickup. I bought a 2006 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 146,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run well when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around the rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
Ford F-150 (2004-2008) :: Turns Over But Won't Start - No Codes
So, my 2004 FX ran perfect as always when I parked it last night but this morning it just will not start. It turns over like a SOB but won't catch (Installed a new Optima Red Top about a month ago). Tried my OBDII but it's showing as "fail" or "no codes".....I tried testing it several times. I've never had ANY problems with it starting.
View 2 RepliesFord F-150 - 1997-2003 :: Shaking And Idle Bounces Between 500 And 750 - Codes P0172 And P0174
2003 f150 5.4, 4x4 ... Truck is shaking pretty bad, idle bounces between 500 and 750, and its throwing p0172 (rich on bank 1), P0174 (lean on bank 2), and it looks like a misfire on cylinder 8 judging by that power graphy thingy. I'm going to check for a vacuum leak tomorrow on the PCV.
View 2 RepliesFord F-150 (2004-2008) :: 2006 - Intermittent No Start Condition And No OBD Codes
2006 F150 4.2 fuel issue? I get an intermitent no start condition and no obd codes. Then I discover that it really isn't intermittent, it only occurs after I have been running the engine. It will not start for at least 5-10 minutes after I have driven a few miles and shut the engine off. So if I wait 5-10 minutes then she starts and runs just fine. I played with this in the driveway to recreate this condition so I could determine if I had a spark or fuel issue (I have spark during no start). I found that 50% of the time I could start it right back up immediately after I shut the engine off. But if I shut it off right away again, then I got the no start condition again and have to wait another 5-10 minutes.
Now with cold engine I can start the motor over and over. To fix this I read forum after forum, which led me to decide that I had a fuel pump driver problem (module) located on back axle under spare tire. I replaced this and restarted the engine many times. The problem seemed to be gone but this only lasted about 30 minutes. Then it would not start at all and still no codes. I plugged my old module back in and the truck fired right up. So I decided I needed to (flash) pcm for new part but that changes nothing. Still no start with new module and runs with old module. I also replaced relay in fuse panel.
Ford F-150 (2004-2008) :: 2006 5.4L - Cranks Slowly But Won't Start - Codes P0201 - 208
Bought a truck from a guy the other day. Long story, but he was a con artist. Told me the battery was dead from cranking it, he couldn't hear the fuel pump so he thinks it needs a new one. Got it home, checked fpdm, it was unplugged. Plugged it in fp running now. Charged battery. Cranks slowly won't start. Appears the engine has been changed. Have codes P0201-208, all injector codes. Cranking it over reminds me of an older distributor type engine that if off its timing. But also of cranking with a low battery. There's a new starter on it already. I'm going to pull the converter bolts on the weekend to see if they may have bound the torque when they installed the engine. Injector codes?
View 4 RepliesFord - Taurus :: 2003 - Running Rough / OBD Code P0172
I have a 2003 Ford Taurus. It has been running rough for awhile. It doesn't happen all the time, alas. I took it to my local repair guy. They first said, oh this happens when the AC is on. But I knew it happened otherwise.
The check engine light came on yesterday, blinking, but didn't stay on. And it was running rough. Check engine light came on, on a Sunday so I had to wait until Monday to bring the car in. They just called and said they can't find anything wrong, ran it on the computer, says it's running fine. I said, did you check the spark plugs, wires, etc? (I am good at googling, to be armed with some kind of info)
I am thinking they just put it on the computer. I suppose it has to be running bad to show anything (?) and even then, it's no guarantee. Anyway. It seems like I am "sentenced" to driving this car until it strands me, catches on fire (I read about that possibility and I have on occasion smelled something burning), or if luck has it, when it is running rough, and I bring it in while it's running rough, the computer finds the problem.
Ford Super Duty (1999-2016) :: Codes P0172 And P0174 / Truck Bucks And Coughs / Zero Power When Driving
I have a 2008 Canadian F250 SD 5.4 triton. Its got 224000km on it and began to get the dreaded 5.4 dieseling when hot and idling. I replaced the timing chains, guides, both tensioners and crank gear. I confirmed the cam timing was correct with the crank key at 6:00 and the chains marks on the R and L. I replaced 2 coils on cyl's 2 and 3. I replaced the MAF sensor, fuel rail pressure sensor, cleaned and confirmed working the crank sensor and both cam sensors. I fixed the broken Bank 2 cam sensor wires. I changed the plugs and replaced all 4 O2 sensors.
Now the truck idles great but when driving it bucks and coughs and has zero power. I cant even get to 80km/hr. The computer now shows codes P0172 and P0174 which means the Bank 1 is rich and the bank 2 is lean. The O2 sensors are working and moving around. The back 02 sensors are both reading in the 0.8Volt range but bouncing around. The front 02 sensors are both moving from 0.1 to 0.8 constantly. The long term fuel trims are +9.5% bank 2 and -4.7% bank 1 at idle. When the throttle is off idle they become +25% bank 2 and -25% bank 1 . How is this possible and what can I do to fix this engine?.
Santa FE SM (2001-06) :: Faulty MAF Sensor - Getting Codes P0171 And P0172
Still having problems with my 2.4l 2002 santa fe. At stand still the MAF readings are within range. At 2000rpm it reads 9.3 gm/s. the info I have says it should be between 7.89-9.83.
When driving along at 50mph, 5th gear, engine speed 2000rpm it reads approx. 25.0 gm/s. at 3000rpm it reads 48 gm/s. Is the MAF sensor faulty?
It is now not running very well with fault codes P0171(fuel system to lean) That code comes up whilst driving at speed. I also get P0172(fuel system to rich). I got that one whilst driving slowly in a car park.
Cabrio :: 2001 - OBD / P1128 / P0411 / P0134 / P0172 Codes Came On
So I didn't pass the smog check for the new used car that I just purchased 10 days ago. Although my old car (same model), was five years older, I never had this problem. I was told that it is a gross polluter. These are the problem that I have to fix:
OBD Fault Codes - P1128 Manufacturer specific codeP0411 Secondary Air inj Incorrect FlowP0172 System too Rich (Bank 1)P0134 O2 Sensor CKT Inactive (Bank 1 Sensor 1)
How this happens?? 2001 VW ...
Ford F-150 (2004-2008) :: 2007 - Rough Idle During Cold Start?
My 07 F-150 5.4 has a rough idle during a cold start for about 1 minute. It happens mostly when the weather is chilly or cold. Also after the first start it doesn't do it the rest of the day. Of coarse they can't find anything wrong and tell me there are no updates for anything like that.
View 3 RepliesFord F-150 (2004-2008) :: 2007 - Motor Start Running Rough At Low RPM
I have 07 sscrew with 5.4. 93,000 miles. At start up truck runs perfect. After 20-30 minutes of running motor will start to start running rough at low rpm. Diesel sound. I can rev up and motor clears up and idles fine. Should I replace VCT solenoids? Or phasers? Or both at one time??
View 14 RepliesFord F-150 (2004-2008) :: Rough Idle Start / Bad Compression Until Warm Up
I have 2004 f150 small v8 (4.7?) Has about 92000 miles.
When warm truck runs excellently. At first start up the idle is very rough and raw gas smell for about 4 minutes then truck runs like new. Will start and restart great until it cools down overnite.
My actron says missfire cyl 3. Did not fix it. Dealer says that on start up compression is zero in cylinder three but is 100% when it warms up. Suggested I run seafoam through it. He thinks it has a vacuum leak or carbon at start.
In my limited knowledge I am thinking:
sticky lifter
bent push rods
warp valve