Starting - Electrical-wiring - Transmissions :: Nissan Maxima Cranks Slowly Then Turns Over But Doesn't Move
Just recently bought a 07 Nissan Maxima SE. Has a few issues.
The car sun roof does not work at all. It worked the day I bought it though.
Has issues turning on. Cranks slowly then after a few seconds of struggle it turns. Didn't have this issue when I bought it.
Goes idle when first starting to drive. From park, I put the car in drive, or reverse, and let go of the brake, it basically does nothing. Engine is on as if it were in park or neutral, but the car doesnt move. When I press the gas it takes a few seconds before it decides to actually move.
Ford Wiring/Electrical :: Battery Goes Dead Randomly Overnight
Earlier this year had dead battery after sitting for a week. 5 year old battery so bought new one battery still goes dead randomly (overnight), instead of playing radio for a few minutes after key off, dash displays "system off to conserve power" ran it thru local repair place (ex ford dealer) nothing found. Voltage 14v at 1800 rpm, lights on". STILL goes dead randomly...
View 6 RepliesElectrical-wiring - Chevrolet - Batteries - Alternators :: New Battery Consistently Going Dead
I recently bought a 1969 chevy c10 pickup. I have been having problems with the electrical system, the battery consistently going dead despite a new battery and alternator installed by the previous owner. Is there a step-by-step for diagnosis of this problem?
View 3 RepliesFord Wiring/Electrical :: 2008 F350 - Battery Frequently Dying
My truck has been sitting more lately, which means up to a week without starting and running. Each time this happens I run into a dead battery. And I mean dead. I've charged it full and then used the truck no problem.
We did a test where we unhooked the negative terminal wiring clamp and ran a meter to check for amp draw. We did this by touching the meter leads to the negative post clamp (unhooked) and to the negative post on the battery. It gives a reading of ~1.5 amps. Trying to figure out where the drain might be.
We'll jut pull each fuse to see if we find the electrical area drawing the amps.
2008 F350 V10 CC SB DRW 4x4
Ford Wiring/Electrical :: 2002 F350 - No Power To AC Compressor
I have a 02 f350 can not get power to a/c compressor have power at high pressure And low pressure can run a hot wire and ground to compressor and it works.
View 1 RepliesFord Wiring/Electrical :: 2004 Taurus Hard To Start / Cranks But Acts Like It Is Not Getting Fuel
While the owner of 2 Ford Trucks, I also have a 2004 Ford Taurus with 28K on it. For a while now the vehicle is hard starting, cranks but acts like it is not getting fuel, however, I can hear the pump come on. Other times it starts right up, but a clicking sound can be heard coming from the firewall area. At times the gauges will not immediately respond when the Vehicle is started and then all at once they will begin to work. Now, my check engine light is on, but my hand held obd will not read it. All the terminal pins look great, obd tester works on my other two vehicles, cigar lighter working, the fuses i checked are good. Vehicle runs great. Can this all be related to a bad module?
View 1 RepliesFord Wiring/Electrical :: 2002 Ranger - Battery Light Comes On And Off
I have an 02 Ranger 4.0 4WD and I have been doing a lot of research to try and figure out why the battery light comes on and off. I was driving the other day down the highway and the battery light came on and voltage gauge dropped. Drive a little further and it goes off, go down hill light comes on, up hill it turns off. (The up and down hill part was probably just a coincidence!) ...
Next day I pulled the alternator and had it tested at O'Reillys and it passed no issues. Yesterday I was driving again the light comes on my way home from the store and stays on for about 3 miles til I got home. Turned my truck off, restarted it later, no light. Today I drove around for a while and about 45 minutes into my driving around the light comes back on and voltage gauge drops and after about a mile it turned off. I stopped by O'Reillys again to have them test the complete charging system and everything passed. On the way home, light comes on again!
So, question is, the battery light was not on when they tested, will that make a difference in the outcome of the tests? I'm guessing not??? Belt looks good, no bad connections that I have found, battery was good...what am I missing? Battery light is still on and voltage low when I start truck after 1.5 hours of being home. Also, I get no magnetism from the alternator when the battery light is on.
Electrical-wiring - Chevrolet - Suburban :: Dead Battery - Ride Control Compressor Runs For No Apparent Reason When Car Is Off
I have a 2001 Suburban (chevy) 5.3 liter Vortec engine, auto trans 4 wheel drive, fully loaded. As of late I come out in the morning to find a dead battery. this happened before and I disconnected the fuse for the dvd player that was installed aftermarket. some times I have to hit my dashboard to get the dash lights to work, now they dont work at all. sometimes the ride control compressor runs for no apparent reason when the car is off. I replaced the battery 3 years ago and it seemed to solve the problem until now. I replaced the battery with an optima red top yesterday and now the electrical system is going haywire. the ABS light is flashing and the service ride control light is on, the fuel gauge is bouncing back and forth from full to empty. What should I do. I am a fair mechanic but electrical is not my forte.
View 3 RepliesElectrical-wiring - Honda :: Delay In Start / Taking 3 To 6 Cranks Before Firing Up
So heres the deal 1989 civic dx hatchback 106k on the odometer automatic 1.5l d15b2 engine . It's been having delayed starts taking 3 to 6 cranks before firing up then running fine, suddenly it dawned on me maybe it was the distributor , so I swapped it with a spare I had because sure enough the old one had red death red dust in the cap. Cleaned the contacts set the timing reassembled, some wires broke on the back of the wiring harness to the distro. Rewired them, the car kept getting worse I jumped it and took it to my friend a vw mechanic it drove 49 miles there fine after the jump, new plugs new wires new fuel filter we did the wire job set the timing checked the timing belt got the battery tested and the alternators new and did a oil change also did a coolant flush a few weeks ago.
It started right up drove it back to Chicago , in the morning I was getting off the highway it stopped running no noises I pulled over 8 cranks later it started parked it 3 blocks away, went to test drive it when I stopped at a light it shut off cramming it and hitting the gas pedal got it to start drove it a block down it shut off at a stop sign and I parked it. What it is I'm throwing code 8 which is a top dead sensor which I think is in the distro which I replaced a month ago. Fuel pump sounds like its priming but you have to gas it and crank it to start it which is odd for a automatic , it is girk injected is this tds sensor going to do that by itself? Or could it be a ignition module? ( what I read online) starter? Main relay , fuel pump switch?
Ford Wiring/Electrical :: 2001 F350 - No Turn Signals When Start The Truck - Fuse 1 Keeps Blowing
2001 F-350 diesel. Out of nowhere, I start the truck and there's no turn signals. Fuse is blown so I replace it. It immediately blows. Tail lights work. No turn signal, brake lights, or hazards. I haven't hooked up a trailer or done anything abnormal recently. Only the #1 fuse (20Amp) is blown. Pulled bulbs and they work fine. Inspected wiring under and near lights. NOTHING! Any way to localize a short?
View 2 RepliesFord Wiring/Electrical :: 2002 F250 PSD - Driver Side Door Unlocks Immediately When Locked / Battery Drain
My 02 F250 is killing batteries. Also, when I try and lock the doors with the door lock switch, the doors lock then the driver side door almost immediately unlocks.
View 6 RepliesFord Wiring/Electrical :: 1998 F150 - Truck Won't Start With A Fully Charged Battery
I have a 1998 Ford F-150. It has an issue with starting sometimes. The truck won't start with a fully charged battery but when I hook it up to a charger, the truck starts normally. It was going to get the wheels aligned today and when the mechanic went to drive it off the ramp, it wouldn't start. I told him to put a charger on the battery and it started right up. Without the charger it just cranked over and wouldn't start. It doesn't do this every time I go to start it only occasionally. The mechanic had no idea what the problem was and has never heard of this kind of situation. I'm assuming it is an electrical problem but I'm not an expert with engines. The battery was fully charged at the shop and the battery is a year old.
View 4 RepliesFord Wiring/Electrical :: 1999 F150 - Battery Draining From Full Charge To No Start In 1 To 2 Days
My neighbor's kids truck battery drains from full charge to "no start" in 1-2 days. 1999 Ford F-150 w/ 4.6L engine. He has already.....
1) Replaced the Battery.
2) Replaced the GEM module.
3) Replaced the Turn Signal Relay.
He did all this before I looked at it....
I checked the following....
1) Truck off, doors closed, hood open... Amp meter shows 3.6 amp draw. When 1st hooked up, shows 4.2 amps... after a while drops to 3.6.
2) To isolate the draw, we pulled fuses while checking current draw at battery.
a) Under Dash fuse Panel. (Yes, with door closed) We remove fuse #15 "stop lamp switch, speed control, brake shift interlock, ABS, PCM,GEM, RABS test connector". (Really... couldn't be more stuff?)
b)Under the hood is another fuse box (drivers side). We remove Fuse #103. "Junction Block Battery Feed".
3) Found that if we remove the #15 fuse under the dash with the door opens, all interior lights flash on/off at about 1 second intervals... weird.
4) Again, another weird one... with the fuse #15 removed and door closed, the "ABS" indicator and some other indicators and dash lights are staying partially lit... not fully lit.
5) The only "aftermarket" stuff i can see is a dealer installed trailer brake system. Wiring looks professional and disconnecting it does not remove the amperage drain.
I'm hoping that one of you wizards will give me the "slam dunk"... if this happens, it must be that. Can I be so lucky? And, yes. I have my own '06 F-150 that i absolutely love. 6-cyl., manual trans, stripped down without even power door locks... my kinda technology.
Ford Wiring/Electrical :: Cranks But No Spark If Voltage Is Down Around 12v
So I've been having problems with my old duraspark 2 ignition box and I replaced that but it didn’t seem to fix the problem. The truck doesn’t start if the voltage is down around 12v, it cranks but no spark. So I put it on the charger a couple hours ago and came inside and was reading old posts on here about testing the ignition system and then just went out to test the negative side of the coil with a test light and low and behold when my assistant went to crank it over the truck started right up like everything was fine. I took off the charger.
So then what I did was I checked the charge at the battery while the truck was running with a dvm and the voltage was 14.33 then I turned on the electric fan and it jumped up to 14.88 and spiked at 15 then held at 14.88. is that normal or is the voltage a little on the high side? If it is high then could it be the voltage regulator or alternator? And could that have been my problem all along instead of the ignition module?
Ford Super Duty (1999-2016) :: 2002 F350 7.3 - Cranks / No Start And Not Getting Fuel
OK, I have a 2002 F350 with 160k miles that cranks fine, but has a hard time starting when it is cold. By cold I mean that it is not hot from being driven in the last 5 hrs or so. No problem starting after being at rifle practice for 3 hrs or after a trip to the store. Always have trouble starting in the morning, like this morning when the temperature outside was 49 deg. I have to crank for quite a while to get it to turn over, but once it catches, it runs like a champ. Afraid I'm going to wear my starter or batteries out because It seems like I have to crank for about 2 minutes.
I have a fairly new CPS replaced less than 15k miles ago, new glow plugs, and recently replaced the leaky bleeder valve on the bowl. This difficult starting condition came about some time before the bleeder valve seal repair, and is still doing it after the repair. This problem seems to have cropped up on it's own unrelated to any work I have done. I am using Mobile 1 5W-40 diesel oil. When the no start occurs, there is no smoke present out of the tail pipe like what you would get if you had bad glow plugs. There is just no fuel getting into the injectors.
Jeep - Liberty :: 2002 Dead - Won't Start At All - Electrical Circuit Is Short?
I have an interlock installed in my 2002 Jeep Liberty Sport. I've been having electrical problems in it ever since it was installed. Prior to it being installed the jeep wasn't mine, it was my grandfathers, and he says it really wasn't driven for a while consistently but it didn't have any electrical problems before the interlock was put in. I'm not sure if this is accurate or not because I'd never driven it prior to the installation. Either way, now I believe I have a short in the electrical somewhere in the system. I'm not sure how to proceed, other then to check the fuses. The battery IS currently dead, but it wasn't.
I was able to start the car and get it down the road, hoping the alternator would charge the battery (the lights were out, none came back on) After a little bit of driving down the road I drove back into my driveway because I was scared to drive without headlights, and shut the car off. It hasn't started back up and now none of the lights or anything are working at all. We've tried jump starting the car, thinking maybe the battery was dead or the alternator went out, but the cables just started smoking and getting really hot. I really need to know how to proceed to find this short, will I have to look at all the wires in the car? Or is it possible to just use the fuse box? My knowledge of electric in a car is very limited, though I do know the basic mechanics.
Ford Wiring/Electrical :: 2002 - Complete Headlight Switch Wiring Diagram?
Any COMPLETE headlight switch wiring diagram? Everything I find online only shows 2-3 wires in each sub connector, nothing with all wires and colors, and what they do. and of course the factory service manuals no longer work on my new computer. the switch and associated wires went up in smoke 2 hours ago, and this truck is my only means of transportation rite now. what i need is headlight wiring with colors so i can temporary hook up a toggle switch to have lights until the new switch and connectors come in next week. I went to pull the switch and connectors out of the parts truck, but of course that does not have fog lights so it uses different switch and connections.
View 14 RepliesFord Super Duty (1999-2016) :: 2002 F350 7.3 - Cranks Good But Hard Start?
Dealing with a 02 f350 7.3 powerstroke . The engine cranks fine . It fires but won't start smoke coming from exhaust while cranking and firing so seems to have good fuel . When it does start it misses for a few minutes and blue/white smoke . When the miss ends so does the smoke and starts fine after that and runs great until it sits for 12 or more hrs . Then back to same start issues . Fresh oil ,new glow plugs, new cover gaskets , glow plugs test at 1.3 ohm across all 8 of them , no voltage drop through glow plug relay , good voltage to each glow plug when tested right at glow plug terminal on each feed right at glow plug , fuel filter housing stays full doesn't seem to bleed back , high pressure oil pump pressure test was high enough to trash a 1000 lbs gauge in 2 to 3 revalutions of engine when cranking . Tested at presure sensor port .
View 2 RepliesFord Wiring/Electrical :: 1990 F250 Hard To Start - Glow Plug Controller Relay Wiring
I just bought a hard to start 1990 F250. Per the board, just replaced all 8 glow plugs with Motorcraft. Still wouldn't start (it turns over but will only start if you use either). I attempted to install a new BWD brand (Borg Warner I believe) glow plug connector relay today...I removed the old no problem, but am unsure what wires to plug where....the only connection that I'm sure about is the blue wire that works the WTS feature...it plugs in easily but I don't know if there are other connections that need to be made or not? All the wires run from the posts and into the bottom of the unit.
View 2 Replies