Ford Super Duty (1999-2016) :: Check Engine Light Code For Injector Control Pressure Low
Traveling cross country & got a check engine light telling me "injector control pressure low". Replaced ICP sensor and injector pressure control regulator. Removed old one and installed the new one.
While looking for one of the nuts that attach the glow plug relay in the valley I found a small round part looks like maybe a valve seat. About 1/2" round with maybe a 1/4" four flute spline in the center. Has an o-ring on one end.
Is this something that followed the old ICPR out and fell off the end when It cleared the mounting hole? It looks like the ICPR would bear against this little thing.
Ford Super Duty (1999-2016) :: 2006 F350 Not Starting - Code P2285 - Injector Control Pressure Sensor Circuit Low
I have a 2006 f-350 6.0 and i went to fill up my truck with diesel. After that the truck did not start. Currently has the code p2285 - injector control pressure sensor circuit low. I tried disconnecting sensor, still no start.
I have the torque pro app and another 6.0 that I use for comparison. Check power at ficm 48 volt, flp 11.5v, FVP 11.5v. Hpop while cranking shows 1400 psi. removed oil filter and see low pressure oil ok, fills up reservoir. ipr at crank about 65%. fuel filter full of fuel.
Replaced the dummy plug on passenger side because originally hpop was very low psi 12. after replacement it went up to 1400 on cranking. What should I be looking at next, should I be removing ipr? should i be looking at crank sensor or cam sensor? Just installed 2 new batteries also because my dad kept cranking the truck until it died.
Checked to make sure fuel cut off relay not triggered, Ok. The truck has been having long cranks before it died. Also right now the injector cycling is 10 seconds long while on my other 6.0 it is about 4.
Ford Super Duty (1999-2016) :: 2003 - Cylinder 3 Misfire With No Code?
my 03 f250 has a 5.4 and i cant seem to get rid of a misfire in cylinder 3. i had a p0353 code but that no longer shows up. i replaced all the coils with Accel coils, replaced the plugs with motorcraft platinum. i have checked the wire all the way back to the PCM and it checks out. i replaced the pcm with one that has been reprogrammed. i have swapped the injector and coil with another position and still get misfire at #3. Replaced the coil connector with a new one. I have good fuel pressure. I no longer get the code but the misfire is still there, unplug the coil and injector while running and no change. Unplug a different cylinder and you can tell the change. I checked compression and its good. I am lost here!!!!
View 14 RepliesFord Super Duty (1999-2016) :: 2005 F250 - Code For Cylinder 3 Misfire
My 5.4 F250 with 200,000 miles having many problems... It all started a few months ago, when the cam needed to be replaced, and a cam phaser was also replaced at the same time. It ran fine after, then threw a code for cylinder 3 misfire. The guy I took it to said it was due to the huge crack in the exhaust manifold and that was messing with the o2 sensor coming up as a cylinder 3 misfire. So, got the new manifold and it was good for a few weeks.
Now, starting the other night, Friday the 13th, it threw a CEL when I was coming into the driveway. It had been throwing a code every once in a while, and I brought it to school to scan it Friday the 13th but there was no code. So, I assume that it is an intermittent problem, no big deal. When I go to get in my truck to go to work a few hours later, the 5.4 cranks... and cranks... and cranks.
I get it to fire up, and it dies again. Run codes, and it says that the cam positioning sensor is broken. Replace both of them, still acts up ie. doesn't start when it does start it runs very rough and stalls. Get it up to my uncles shop, and replace fuel filter.. Still runs like trash. Run codes now, and it says rich/lean in bank 1.. My uncle tells me to move my truck out of the shop, so I start it up, and it runs great. No hiccups, it idles perfect as I move his truck out of the shop first.
I park my truck outside and let it idle for about 10 mins, and when I come back out it is still idling, perfectly fine. I get in, put it in reverse, and get about 20 feet when it dies and will no longer start back up. What could be going wrong?! Sick of throwing money into this thing! At one time while started up in my uncles shop, it was blowing black smoke, as if it was a diesel!
Ford Super Duty (1999-2016) :: 2003 5.4 F250 Head Gasket / Misfire Code On Cylinder 4?
After replacing most of the underside of my Super Duty, Complete front end, backing plates, brakes, rotors and shocks, I have a misfire code on cylinder #4. I replaced the plugs, cleaned the MAS and filter and rotated the coil to cylinder #1. Still have a misfire on #4 and noticed the coolant slightly low and some condensation on the oil cap. Could this be the intake gasket? My mechanic is away for 2 weeks and I think the price at the dealer will kill me. I have 63K on the truck, don't tow and plow mostly family members. It's getting a little rusty but is still in good shape.
View 13 RepliesFord Super Duty (1999-2016) :: 2008 F350 - Multiple Codes / Cylinder 5 Misfire
My dads truck started misfiring last week, first thing i did was scan the codes and got p0303, p0304, p0305, p0306, and p0308. Its an 08 F-350 5.4...already changed out the spark plugs and the same codes came back. I decided to do some further testing and so far all coils had spark as well as 12.4 volts going to each. I did check the switching signal and that was present as well.
Moved on to the injectors and i checked each connector with my noid lights and it flashed on all cylinders. Did a resistance check on each injector and they all registered 12.4 ohms. We did switch some coils around and all the same cylinders misfire. My next step is to do a compression test.
My biggest question is if there are any common problems with these engines besides the coils, by the way this truck has the brown coil boots and the spark plugs that dont break in the engine.
Ford Super Duty (1999-2016) :: 2008 F250 - Random Misfire Detected On Cylinder 7
Truck Specs:
2008 f250 super duty 5.4l
78xxx miles
4x4
Automatic
Issue:
P0300 (random misfire detected)
P0307 (cylinder 7 misfire)
Let's start from the beginning...
I was getting the notorious 5.4l ticking sound. After doing research on this issue. I found that it could be a few different issues including:
Cam Phasers
VCT solenoid(s)
Loud injectors
Valves
Exhaust leak
Loose spark plug
The list could possibly go on, but these being top concerns or issues to look into.
I took it to my mechanic and wanted him to research the ticking problem. This was my primary concern due to it was getting worse over time. I didn't want to do more damage than what was possibly already done. I told him to go ahead and change the spark plugs while you're checking into what's going on. (I know those plugs can break and I didn't want to do that.)
At any rate... the plugs got changed to motocraft brand (I know the trucks can be finicky with the parts you put back into them so I went with the motocrafts to avoid any complications.) After the plugs were changed, he told me that the ticking was caused from a blown exhaust manifold gasket (yay me... not internal parts or anything too serious. Sweet!)
I had to reschedule to get the gasket done, but knowing what it was now I wasn't too concerned about driving it. So I did. The new plugs are also in the truck at this time. I drove it the next day and right away.. I noticed a misfire. Thought maybe the plug was bad. I told my mechanic about it and he said... Sounds like a COP to me.
So I get a new COP. Okay.. easy fix. Installed it and still got a misfire. Told my mechanic and he said get another COP. So I'm thinking.. "Okay.. get a new part to fix a new part.. sounds logical.. lol" so I do what he thinks might be best. I replace the COP with another new one and it's still misfiring. The new cops are also motocraft brand as well.
Okay... next step.. he claims it may be a VCT solenoid issue. At this point I don't care.. I just want my truck fixed. So he replaces the driver side solenoid. Still misfiring..
So after doing some research on the scanner... we locate some issues that are the exact symptoms I'm having. Misfire.. at low rpm.. during cruise control.. and a sudden at idle.
This information states for this drivability issue.. to spray injector cleaner/carb cleaner into the engine and possibly clean it out. Makes sense. He did this as well as changed the fuel filter. Also did a pressure test on the injectors to make sure they were good. They were. After spraying and cleaning it out, it was taken for a test drive and it seemed okay... but not perfect. The next day.. the misfire came back.
He said that if the misfire returns, that I need to contact the dealership and see if there is a pcm update. The dealership said there probably is but can't tell me until the computer is hooked up to it. (Of course there is a charge when it's hooked up) again.. whatever.. I just want it fixed. The truck is scheduled to go in next Wednesday for that. If that doesn't fix it, my mechanic said cam phasers possibly bUT still not sure for sure..
Ford Super Duty (1999-2016) :: 2005 F250 - CEL Code P1299 For Cylinder Head Temperature Sensor
(The truck is a 05 f250 with a 5.4l). The problem first started out with the engine temperature gauge spiking and then resetting itself when the truck is turned off and then turned back on. If I drove the truck for any distance it would go into limp mode and the CEL would come on. The code was p1299, which is the cylinder head temperature sensor, and I replaced the sensor but no luck. Then the shop and I went through all accessories hooked up and couldn't find a short until I remembered that my prodigy break controller would occasionally read "ol" or "sh" which both readings are from shorts. I tow a enclosed trailer about 85% of the time and the past week I have been towing it with a different 250 and the same break controller without a problem so I have eliminated the trailer. But the shop just said the problem was the controller and unhooked it.
Now the next day it threw the same code with the controller unhooked and the trailer hooked up. after thinking it seemed that it was happening when i accelerated so I took apart the 7 pin and sure enough there was a little water in it, but after driving it around for a little and no code being thrown I hooked my break controller up and it still was showing ol or sh so i believe there is still a short. Also I noticed that my voltage is reading right at 13v instead of the 13.8-14v it was reading before this issue arose. I think I have narrowed it down to the 7 pin harness and/or electrical in the break components, but do not know what would loop back to the temperature sensor.
Ford Super Duty (1999-2016) :: Low Injector Circuit On All 8 Cylinders
2006 6.0 superduty showing low circuit codes on all 8 cylinders so i checked the FICM and it has 48v when key is on and while turning engine over. What to check next?
View 11 RepliesFord F-150 (2004-2008) :: Engine Missing While Driving - Code P0202 - Injector Circuit Malfunction Cylinder 2
Yesterday driving to work felt the engine missing, on the way home got a CEL pulled the code when I got home it was P0302, so I started with the easy and put a new coil pack, same issue, so I prayed and pulled the plug (it didn't break). Put a new plug and a second new coil pack (just to be sure, and yes I keep extras dang 5.4). cleared codes and started it this time got P0202 Ford - Injector Circuit Malfunction Cylinder 2, so I checked Ohms on #2 and it was 12.6, #1, 3, 5,6 all have 13 Ohms, didn't check #4, 7, or 8 because my big hands and the probes on my multi meter. Checked the wires on all of them and have 12 volts with key on, not running. I read another check to put blk in pin and red on pos batt terminal, and that it was supposed to go 12 to 0 off and on with engine running, All of mine went up to 14 volts and stayed no switching. Is there something I am missing to check before replacing the injector on #2?
View 6 RepliesFord Super Duty (1999-2016) :: Loud Cam Phaser Or Fuel Injector Noise / Tap
uper Duty 6.2L ... Alright, the loud cam phaser or fuel injector noise/tap..Is this just a cold weather issue or is this going to be like this all the time under start up? Mine was quiet until now (1200 miles) now under cold start loud knock/tap sound. Seemed to go away when truck warmed up and was idling. Was or Is there any fix to this noise.
View 14 RepliesFord Super Duty (1999-2016) :: 2008 F350 - P0088 Code / HPFP Replacement
2008 F350 6.4 ... So I've been reading all about the spartan tuner throwing the P0088 code, and the ford band aid fix, I guess my question is, I'm going to have my HPFP replaced for peace of mind. Truck has 106,000 miles on it. Will i have an issue at the dealer if I show up with my tuner/exhaust on the truck? I'm not worried about warranty obviously, I just want to know are they going to have to unplug the tuner? Or something, I am just concerned how they'll go about putting the new HPFP on.
View 6 RepliesFord Super Duty (1999-2016) :: 2008 F350 - Keep Getting A Lean Bank Code - O2 Sensor?
I keep getting a lean bank code. I have cleaned tb and replaced one of the rubber lines. It only comes on when I take a good ride with the truck. Not sure what else it could be. I'm thinking O2 sensor maybe.
2008 F-350 5.4 3V. 65k miles
Ford Super Duty (1999-2016) :: 2008 F250 - Throwing Code - No Power - Misfiring?
My 2008 f250 6.4l just got out of the shop a week a go new small block and new pistons, throwing #1 constrabution code,map sensor and #1 cil misfire you can hear air come out of the intake, I am guessing valve train or lifter..... other problem two days after the truck throwing the codes i went to take it to the shop and would barely drive floored struggle to go 10mph put it in park rev up normal will go in reverse normal just no power in drive, no transmission codes, had it towed to the diesel shop, mech said might be a fail safe on transmission from the engine codes? it has egr/dfp h&s mini maxx tuner, the truck has 170k on body 11k on new engine before the new block that was put in last week.
View 6 RepliesFord Super Duty (1999-2016) :: 2001 F350 - Injector Change Now Whole Bank Not Firing
2001 f350 7.3 Changed front injector drivers side inspected all 4 glow plugs on this side turned motor over my hand 5 time reinstalled plugs put back together hooked both plugs back up started truck and no of the cylinder on drivers side are firing checked them with temp gun!! what did i not do or do wrong.
View 4 RepliesFord Super Duty (1999-2016) :: 2008 F350 - How To Locate Keyless Entry Code Sticker
I have looked at many of the other treads and I can not find the answer. How do I locate the keyless entry code sticker in my 2008 F350? I just bought the truck used, I do not have the card that is delivered with the truck and I don't want to pay the Stealership to hook it up to there computer. I am looking for the RAP or the computer module as it is called in the owner's guide.
It is not behind the glove box, there is no longer a fuse access panel under the dash like the earlier SD's, the drink holder under the upfitter switches does not "pop out." Before I start with any tools, I am looking for input.
Ford Super Duty (1999-2016) :: 2008 F250 - Replaced ECT Sensor And EGR Valve - Getting P0117 Code?
I am running a 2008 Ford F-250 with the DPF Delete and the Mini Maxx Tunner. I have replaced the ECT (Engine Coolant Temp Sensor) as well as the EGR Valve and housing troubleshooting this issue. Both the Engine light and the coolant icon come on when I turn on the vehicle. I am getting a P0117 Engine Coolant Temperature Circuit Low code on the Mini Maxx.
From a cold start with codes cleared if I turn the engine to ON even without starting the engine the Engine codes will come on and the the Mini Maxx will read engine coolant temp 302 and will go into Defueling Mode. I have repeatedly tried removing and reattaching the connector to the ECT thinking it could be loose connection. I can't drive the truck because there is no power and i know the engine is not hot because I have let it sit all night before doing these tests. I do not have a scanner to test other than the Mini Maxx. Other notes: I have checked Coolant I have checked Oil
Ford Super Duty (1999-2016) :: 2005 - Injector Plug Cord Location To Heat Injectors?
2005 Ford F-250 6.0 FX4 Quadcab
Where is the cord to plug in to heat injectors on this model? Or does this model not come with the cord to plug in?
Ford Super Duty (1999-2016) :: 2008 F350 Going In Limp Mode Without Engine Light - Code P0088
Replaced HPFP 38,000 miles ago. Truck began going in limp mode without engine light, wrench came on in dash, gave codes for brake switch, anti-theft, some other weird codes. Had those codes cleared, ran for while then water separator came on, drained the water out, came back on. Read some forums, so I removed and cleaned the housing, cleaned off the sensor. Had code cleared and ran good for about a week. Then guess what engine light comes on, limp mode.
Went to Auto Zone, pulled code P0088. This truck runs awesome until limp mode. No other problems. I take it to the ford dealer, scanner pulled P0088 and the water separator code again. I have read alot of remarks about this P0088 code. Can there be another cause for pulling this code, only 38,000 miles later. I had them do the TSB 12-07-07 but I have also read it can only be done if the P0088 is the only code. I just really feel there is an underlying issue with these 6.4's.