Elantra XD (2001-06) :: Code P1166 After New Alternator Installed And Stalling
Code P1166 showed up after I have new alternator installed from coolant leaking onto it. I dont think that is the cause though. In the fall I found some acorns in the air box and just recently in the heater fan. In December, after the acorns were found, the car had a low idle a seized alternator and a broken belt.
No acorns are in the air box anymore, or in the heater fan. Car has more of an erratic idle and stalls now that it is parked on an incline.
Santa FE SM (2001-06) :: CEL Comes On When Driving Down - Code P1166
So I go on vacation, and as we're driving down, the CEL comes on with p1166 pd1166. Get home the code still pops up. A month later small oil leak is detected. Clean the throttle body intake, fuel and exhaust systems. Oil leak gets worse, turns out the crank shaft seal has failed. Shop cleans out the oil, and replaces the timing belt. Clears the code and the CEL stays off for 5 days. I clear the code and Its good for days. Get it up over 50 and the CEL pops on. So today go for a trip mostly highway driving. I go over 125 miles with out the CEL coming on. Check it and the reader reports pd1166. Clear it. Driving back 4 miles and the CEL comes on. 2 codes p1166 and pd1166.
What are the time parameters for logging a pd1166 and the p1166. No engine issues, no performance issues. Gas mileage is 17-19mpg.
Ford 7.3L Power Stroke (1999-2003) :: E99 Stalling And Sometimes Running Rough - Codes P1280 And P1247
E99 Romps on start up and randomly dying. Bought this truck about 3 weeks ago. Previous owner mentioned he had issues with it getting hot and shutting off and not starting. Has new IPR, ICP and pigtail, I just put in a new fuel filter. Has 206k miles on it and is the 4R100.
The past two days after sitting all night I have been cycling the key twice and it hasn't done its romp. Typically when it does I can tap the pedal once and it goes away. This I could deal with but its started to die randomly while driving, never while cruising down the road. Its either just after starting it and rolling slowly or slowing down for a stop or to turn. When it dies, I can put it in neutral and it fires back up no problem. SES light usually comes on for about 10-15 seconds after but goes away.
Replaced the grey CPS that was in it with a dark grey one from RiffRaff Diesel. Got a Edge CTS2 to figure out the problem, the codes Im getting are P1280 and P1247.
The ICP pigtail they replaced they spliced on with butt connectors. I plan on pulling it to check for oil and make sure it does look new and redo the connections with solder then shrink wrap them.
I was told to check the IPR% under full throttle which I did and it never went higher than 36.7
The truck did start running rough around 45-50 mph and I did get a video of the ICP jumping around while cruising down the road.
Then I went through a drive through and the truck kind of hiccuped like it wanted to stall and the ICP went right to 725 PSI and idled up and stayed there until I started to leave.
Truck is pretty much stock, K&N air intake and muffler cut out and straight piped.
Here is a link to the videos I got :
e99 7.3 ICP fluctuation while driving - YouTube
e99 ICP steady at 725 PSI after acting like it wanted to stall. - YouTube
Santa FE SM (2001-06) :: Car Has Hard Start, Rough Idle With Stalling
My coworker is giving me a clean 2001 Santa Fe with 151000 miles. It was running fine then all of the sudden it lost power but was able to stutter home. I went to check it out it started fine but idled a little rough. When I revved the engine it rose to about 2500rpm and stuttered then stalled. Kind of like it was rich and choking out. It then had difficulty restarting.
View 10 RepliesFord F-150 - 1997-2003 :: 2001 - Running Rough When Cold / Stalling Out When Coming To A Stop Light
2 questions regarding our 2001 F150 Supercrew. My 2 questions are:
My 2001 Ford F150 Supercrew (5.4L, 230,000 miles)has the check engine light on with the code reader telling me that it is the P0174. The truck would run rough when cold (usually in the mornings) and sometimes it would get close to stalling out when coming to a stop light. So we would quickly put it in park and give it some gas to rev it up a bit. After the truck gets warmed up, it runs great with no hint of the rough idle. Since this all started I have changed out the PCV valve and replaced the PCV hose (including the elbow). I have also replaced the Idle Air Control unit but that didn't really make a difference.
We then experienced a cylinder #4 misfire which we resolved by changing out the cop with a new Motorcraft unit. The misfire went away but we still had the problem of running rough at idle to the point of stalling out at stops when the engine is cold. A few weeks ago we cleaned the MAF sensor and that seemed to work. The truck doesn't run as rough now (when cold) at stop-lights, but occasionally it will still have the loping idle. We cleared the check engine code and it stayed off for about a week before returning.
I don't know what else to check other than trying to see if there is some type of vacuum leak, but I don't have access to a smoke machine nor would I know how or where to hook one up. Removing and cleaning the throttle body would work? What could be causing the trouble, or what I should do to further isolate or troubleshoot the problem? I saw a you-tube video on the F150 intake manifold gasket possibly being the problem and although I hope that isn't the trouble with my truck, if it is then I will have to deal with it. We need the truck to get to work and the car is now due for a registration renewal, but we can't get a California smog certificate with the check engine light on.
Santa FE SM (2001-06) :: Lack Of Power / Rough Running
Well today I have moved on to the next project on my 02 v6 4X4 Santa Fe, which is the rough running. When I got the car, it had CEL with codes for misfire #5 and lean condition codes. I noticed the wires were in need of replacement (one had black tape wrapped around it) so changed the plugs and wires. The 2 hoses, one that goes between the valve covers on the pass side and the hose between the valve cover and throttle body on driver side were both cracked so replaced them along with a few other vacuum lines, just because I had access to them. Cleared the codes and it still runs like crap, but after 112 miles, town and highway driving, there are no CEL codes. When its first started it idles at 1500 and sounds like its missing and has very little power going down the road. When it warms up seems to run a bit better but still nowhere close to what it should. Equal compression on all 6 cylinders and has power to all 6 injectors and tested to be sure there was a pulse to them as well. Coil packs all tested well. the exhaust is in bad shape and don't know if that would have any effect on how its running.
View 6 RepliesSanta FE SM (2001-06) :: Rough Running While Driving / 2 Of 4 Cylinders Lost
2001 Santa Fe with 2.4 engine auto FWD 198k miles. When it is started first in the day, the engine sounds good and shifts well. After a few minutes and also after stops, first gear works well but then the following gears do not work well almost as if the engine and the transmission quit talking to each other. Traveling at 60 mph starting up a medium hill, the car downshifted and could not pick a gear. Although I pushed the pedal harder, the car did not respond rather continued to slow down. It acts like I lose 2 of the 4 cylinders in all cases. I replaced the spark plugs and two of them had oil on top of the plugs and also all around the threads. I replaced both coils thinking that one of them was the issue but no change has been observed. I replaced the throttle position sensor; no performance change. I do not believe it is the transmission as I have not notice any clunking, or bad shifting when starting out. While coasting at 40 mph in neutral and my pedal pressed at a certain position, the rpm gauge fluctuated from 3k to 3.6k many times for the duration of 20 seconds.
View 2 RepliesSanta FE SM (2001-06) :: Engine Running Rough When Started / Backfire When Give It Gas
I have a problem with my 01 santa fe. When I start it the engine runs rough and when u try to give it gas it pops or backfire through throttle body and air intake tube? Checked the timing belt its ok hasnt slipped.so im stuck at this point.
View 8 RepliesSanta FE SM (2001-06) :: 2.4L Engine Running Rough / Rich Smell All The Time
When firing up the engine cold it runs really rough, smells very rich all the time, even warmed up. No codes set, fuel trims are within 5-10%. I've replaced the front O2 sensor, swapped crank & cam sensors, Map sensor (have lots of spare parts) & I'm sure there was more things I've changed but can't remember. I have a snap on scanner and everything is within parameters.
I have not checked the EGR valve or solenoids yet. It's a 2006 Santa Fe 2.4l 5 speed, new timing belt & balance belt replaced when I dropped this engine in. Is there a common problem with these that I could begin looking for?
Santa FE SM (2001-06) :: Engine Running Rough At Idle / High RPM And Appears To Be Misfiring
Recently replaced plugs/wires on soon-to-be 10 year old '04 SF 3.5L (157K mi.) for the first time.
Plugs were OE Champion Platinum and all 6 looked identical except for excessive gap of .010 +/- due to all the miles. Replaced plugs with same as OE. Old plug wires looked good, but replaced them with aftermarket wires ( fit was as good as OE). Also replaced plenum gasket.
Problem is: engine runs rough at idle and high rpm and appears to be mis-firing. CEL is off and code reader shows no Trouble Codes stored.
Santa FE SM (2001-06) :: 2004 2.4L Engine Running Rough And Shakes After Timing Belt Replacement
I recently replaced timing belt and balance belt on my 2004 santa fe 2.4l and now the engine runs like crap and shakes badly. I went over all timing marks again and again and I am at a loss.
View 9 RepliesGolf IV / Jetta IV :: 2003 GLI 24v VR6 Running Rough And Stalling Out
I have been beatingy head against the wall for the last month with this car. It started out by just running really rough and stalling out. Found out that I had a bad clamp on the air intake that attaches to the throttle body. Replace that after I already replaced the MAF. Everything was great till couple days later then the car just crank crank crank no fire....
I cleaned the grounds pulled the plugs and coils, had perfect spark. Put everything back come to find out after going thru my Bentley manuals I jumped around the fuel pump relay fuel pump kicked on perfect started great! Replaced the fuel pump relay BAM! Ran great!!!! For 2 days..... After that right when I pulled into the drive way the car would not start.... So I tried everything again.... To no avail..... Check the codes again, now I'm throwing these codes which yes I did cross reference in my Bentley manual.
P1117- O2 sensor heater circuit bank 1 sensor 2 short to ground
P1198- O2 sensor heater circuit bank 1 sensor 2 electrical malfunction
P1472- EVAP emission control LDP circuit short to ground
P1516- Intake manifold changeover valve circuit open
And the dreaded same code I've had the whole time........
P0102- Mass or volume air flow circuit low input.
I have also tried tracking down any bad wires, and testing resistance...
Oldsmobile - Cutlassciera :: 1996 / 2.2 L4 Running Rough Idle And Stalling
1996 / 2.2 L4 / 186k / Upper engine rebuild 30k ago
Car was driven on a errand by my mother. Upon trying to leave for home, the car started running very rough, and stalling. From the description she gave on the phone, it sounded like a plugged up exhaust. I told her to get some fresh gas and ease it home after.
When I checked the car for codes, I got 2. A P0300 and a P0122. Okay, so the throttle position switch has taken a dump, that's easy enough. The car has 186k miles, but my constant nannying usually soothes her, so surely that's all, right? God, I wish that turned out to be true.
I pulled the plugs, and #4 was gas fouled and sooty, #2 and #3 looked lean, and #1 was partially wet fouled. There was also gasoline in the oil. When the car would run, it would run the gambit from idling semi rough then stalling out and refusing to restart, almost like it was flooded, to idling scarily bad and no pedal response, to running too high of an idle and idle searching.
Since I have:
Replaced the TPS
Replaced the IAC
Replaced the CTS
Replaced the MAP
Replaced the ICM
Replaced the FPR
Replaced both ignition coils
Replaced plugs and wires
Replaced the fuel injectors
Replaced the PCV
Replaced the fuel filter
Checked the pintle on the EGR (looked good, cleaned)
Checked for Vacuum leaks (as best I could)
Checked the Fuel pressure (40 PSI) (drops to 20 after shutoff)
Checked for exhaust restriction (ran open exhaust manifold)
That brings us to today. New injectors just in, and the engine will run, but rough and loud. It almost sounds like the firing order is off slightly (I am using 1342 or from L to R 4132) and throttle control is almost non existent. It also shuts off when its warm almost like its flooded. No codes are showing. (despite discovering a sensor in back being unplugged and the O2 sensor being unplugged at times).
Kia - Sephia :: Stalling Out And Running Very Rough - Catalytic Converter Replacement?
I was told that my 1997 kia Sephia needed a new catalytic converter by a very reliable shop. My car had been stalling out and running very rough. They did replace the distributor cap which seems to have increase the overall performance and that same day i had a smog check and passed with flying colors! Why would I still need to replace my converter if I passed smog. My car has only 36k on it.
View 19 RepliesChevrolet - Equinox :: 2010 - Running Rough And Stalling When Idling
I have a 2010 Equinox with about 52000 miles on it. At about 48,000 I took it in for the 50G maintenance. The car ran with a fluttery sound that I did not really notice until it was brought to my attention. Recently the car began running rough and stalling when idling. there were no warning or indicator lights lit. I had OnStar run a remote diagnostic and they said there were no codes. The day after the diagnostic the check engine light went on , while at the same tie the rough idle and stalling went away.
I brought the car in for service at the dealer. They said that the car had several codes indicating low oil and the car was down 2 quarts but there was no leak. They also said the noise I heard was the timing belt. The noise is gone after the service and the car is running smoothly. Coincidentally, or not, I got a notice from GM saying they were changing the oil monitoring software on the 2010 Equinox to recommend me frequent oil changes.
1) What could cause the car to loose 2 quarts of oil over less than 6000 mile? Is this normal or an Equinox problem.
2) Would low oil cause the timing belt to make a noise.
3) Do I have a lemon and am I being ripped off y the dealer?
Toyota - Corolla :: 2004 - Stalling / Running Rough And Hesitate On Acceleration
I'm having issues with my 2004 Toyota Corolla with 118K. Every few weeks, the car will go through a phase where it will stall out, run rough and hesitate on acceleration. Oftentimes it is accompanied with the rotten egg smell coming from the catalytic converter. When I decelerate to a stop light, the car will stall. When I start it back up, I have to rev the engine to 2000 rpm in neutral to keep it from re-stalling. Once I get up to about 10-15 mph, the car will jerk and sputter, and at 40mph, the jerking motion gets worse. If the car doesn't stall it'll run rough and have the rotten egg smell. I'm assuming the smell is from unburnt gas.
I find it happens more often when I don't let the car warm up for a few minutes. I've taken it to my mechanic, and i've gone through 2 MAF sensors, cleaned the throttle body. I changed the iridium plugs at 102K and am on top of maintenance with filters, oil and such. Of course when I bring it to the mechanic, the problems don't show up, and we are kinda blind to what could be causing the issue. Also, if I park it for a day or two after the issue occurs, the problems go away. What to look for?
Ford Ranger / B-Series :: 1985 - Running Rough - Bogging Out And Stalling
I am fairly new to this stuff but I just got a 85 Ranger 4x4 and its running pretty rough it will be fine then all of a sudden it will bog right out and want to stall so I have to keep my foot planted on the gas and it pops and spudders and eventually runs normal again? Its a 2.8 V6 carb...
View 14 RepliesSanta Fe (CM - 2007-12) :: 2009 - Rough Idle / Random Stalling
I am happy to own a Hyundai Santa Fe (2009) 2.7l which originally originated in the US. It is a really nice car, however, it recently over time developed the problem, which causes some pain - firstly it started with rough idle (pulsating), now it began to stall from time to time when decelerating.
[URL].....
I tried to plug a OBD reader and here's what I get (well, that's a "pending" fault, but still might be useful).
I tried to browse around the internet. I believe it is unlikely that 2 oxygen sensors fail at the same time. It could possibly be caused by vacuum leaks or faulty MAF. Is it a common fault among Santa Fe?
Ford F-150 (2004-2008) :: Knocking Noise / Running Rough And Stalling - P0340 And P0345
I have a 2006 f150 it was making a knocking noise after the engine oil temp reached 160* and made the noise to 1700rpms. I thought it was the cam phasers so I replaced them. The truck is still making the noise and running rough and stalling but not as bad and not as often. Before it did it all of the time. The truck is timed properly. I had a new cam sensor and tried it but that did not work. I watched vct on the scan tool and both cams are in sycn.
View 2 Replies