Santa FE SM (2001-06) :: Hard To Start After Fill Up - Rough Idle And Engine Shuts Off
Every time i stop for gas..my 01 santa fe is hard to start..it would take 4 to 5 start before she goes, then i have to keep the rpm up, bring her to idle..after that shes ok, till the next fill up.. the only way around this is to keep her running while gassing up..while filling up she run rough idle, some time engine shuts off..then its hard to start..
View 5 RepliesCentury :: 98 Buick Custom Hard Start Under All Conditions / Rough Idle And Stalling?
[URL] I even pulled the same P0170 code. And what I need to do before I spend a boatload of money and wind up sleeping in my car instead of driving it to work or lack therof is to start a troubleshooting list starting from where Sabot's update left off, i dont even know where the vacuum line is that he mentions and if i sprayed carb cleaner on it would i get a jump in engine RPM or a stall as a test?
What I have done: Cleaned MAF sensor, changed fuel filter.
What I have not done: Checked all vacuum lines, Tested fuel pressure, Tested for compression issues due to blown head gasket.
there is also a puffing noise coming from the exhaust side of the engine, im gonna grab a bottle of baby powder this afternoon and test for air leaks, i dont believe it is a misfire...
Ford - Explorer :: 2006 - No DTCs / Hard Start / Rough Idle And Stalling
I'm a diesel mechanic and know my way around Powerstrokes, this 4.0 is not what I would usually work on, but I have a friend who has 2006 explorer 4.0L SOHC, someone told him he needed a motor with out explanation why, so I didn't want to see him get ripped off. The problem is it idles very rough, hard to start, and stalls. There's no DTCs , if you hold the accelerator slightly it will stay running, but once you let off it will either idle really bad and misfire or cut off, once pushing the accelerator the rpms raise very smoothly up til 3500 which is what I assume the rev limit is in nuetral.
I've done checks with focom and forscan, I was thinking possibly a bad fuel pump, while monitoring fuel pressure I see a range of 289 - 326 kpa with 26% fuel pump I guess duty cycle would be the correct term(once again I'm a diesel guy, and use to dealing with IPRs and Hpops) not sure if the desired fuel pressure is relevant on these but it always stays at 269kpa. I believe that equals out to 40-48psi while I believe this system is supposed to have somewhere in the range of 60 - 70, but I wouldn't expect to get a rough idle with no load with almost 50 psi of fuel pressure.
So with no DTCs Im baffled, and don't want to start wasting money just throwing parts at it. I've thought everything from fuel pressure sensor, to coil pack(replaced 4 months ago) to crank and cam sensors.
I did end up getting a code p106, but I believe this is because I didnt tighten the intake hose after checking the throttle bottle, I just slid it back on. out of the 4 days of testing first time I seen a code pop up besides unplugging some sensors here and there to make sure the pcm would actually register a dtc.
Santa FE SM (2001-06) :: Occasional Hard Start / V6 Refuses To Idle
Occasionally, when restarting my 2003 Santa Fe V6,it refuses to idle. If I manually press on accelerator pedal it will start and run and after a few moments it will run fine. This seems to happen more often in high temps i.e., deserts.
View 5 RepliesSanta FE SM (2001-06) :: Cold Start Rough Idle For 20 To 30 Seconds
I'm having this cold start issue with my 2001 SF, but it doesn't seem to be fuel related like as the car starts fine but after about literally 1-2seconds the RPMs drop below 1k and the car will stall if I don't put my foot on the accelerator and keep it around 1000-2000 RPMs. But if I happen to make the revs go too high and let them drop again it seems like it wants to stall even easier. After about 30 seconds it smoothens out and drives almost perfectly except for a slight lack of power than normal going uphill (A.T drops to 2nd gear, sometimes 1st depending on the incline). We have had the coolant temp sensor and the fuel pressure sensor replaced. Could it be the MAF? We did clean it one time but it didn't seem to work much at all. Recently out of curiosity, I disconnected the MAF sensor and started the car it being started for a few days. No issue with idling whatsoever!.. ??
View 4 RepliesSanta Fe (CM - 2007-12) :: 2009 - Rough Idle / Random Stalling
I am happy to own a Hyundai Santa Fe (2009) 2.7l which originally originated in the US. It is a really nice car, however, it recently over time developed the problem, which causes some pain - firstly it started with rough idle (pulsating), now it began to stall from time to time when decelerating.
[URL].....
I tried to plug a OBD reader and here's what I get (well, that's a "pending" fault, but still might be useful).
I tried to browse around the internet. I believe it is unlikely that 2 oxygen sensors fail at the same time. It could possibly be caused by vacuum leaks or faulty MAF. Is it a common fault among Santa Fe?
Santa FE SM (2001-06) :: Stalling And Running Rough - Codes P1166 And P1167
My 03 Sante Fe is running a little rough and is stalling. My Mechanic said this P code was going to run me $1300. I'm not very mechanical , but this just seems very high. He said that aftermarket sensors would not work and only Hundai parts for the fix.........
2003 Sante Fe, LX, 3.7 l engine
Stalling - Toyota - Rough - Celica :: 2001 - Idle Roughly / Shakes A Bit
I have a 2001 Toyota celica GT auto. It has 120k miles. I seem to have an issue that really is not causing a problem except for annoyance. After coming to a stop the car seems to exhibit the signs of stalling (car idles rough, shakes a bit) however the car never stalls. Once I start driving all is well. Now I took it to the dealer and they replaced the Idle Air Control Valve which is under the throttle body. They said it was getting stuck and due to the higher mileage possible. It was replaced and the problem is still there. The funny thing is even though the car exhibits these stalling symptoms the idle does not drop below 500 rpm (both dealer and I have verified this).
View 3 RepliesSanta FE SM (2001-06) :: Engine Stalling / Idle Very Low - Code P0102
Trying to get my daughters Santa Fe going. Engine stalling. Idles very slow. 2001 model with 2.4 engine, auto trans.
Code P0102 is active. Cleared with scan tool and it comes right back.
Replaced the MAF and no change.
Checked the intake for leaks / vacuum leaks and none found.
Checked for debris up-stream from MAF and all is clear.
Air filter is clean and dry.
Checked harness plug and found the pin 5 has 4.6 volts on it from PCM. This is the signal wire from MAF to PCM. 4.6 volts is KOEO.
IS THIS NORMAL OR IS PCM BAD ??? All other pins / voltages on harness plug are normal.
Saab - 9-3 :: Rough Idle And Loss Of Power - Stalling On Start Up
SAAB 2007 9-3 - Recently my car has been having a rough idle and stalling on start up. It has been getting worse and I need it fixed ASAP for a long trip coming up. I cannot have this thing die on me while I'm 300 miles from home....
At stop lights the car will have a rough idle while in park and reverse. While in neutral, nothing. As soon as I accelerate, it goes away but does have a lack of power if I really push the pedal. Once I am in 3rd/4th gear, the car feels normal with no issues. If I am on the highway and slow down then need to accelerate, it goes back to losing power BUT if I change over to manual and downshift, car gains power and goes back to normal.
Here's what I have done so far:
1. Changed the spark plugs twice. Once with cheap ones, the second time with expensive ones. I also swapped out the boots.
2. Cleaned the MAP sensor
3. Cleaned intake sensor
4. Replaced air filter
5. Changed oil
6 New battery
The engines gives no codes whatsoever and I have taken it to a couple places and their readers don't see any codes. My SAAB has a built in fuel filter and this cannot be replaced unless you replaced the whole pump (to my understanding). I plan on buying some Seafoam today and see if that works. Also, I have been told to clean my air intake valve but I cannot get the damn tube off! I feel that if I yank and pull on it, it's going to damage the tube. I am not seeing any obvious leaks anywhere. One thing that is weird about my car, since I have bought it used a few years ago, my headlights/tail lights/blinkers go bad QUICKLY!
Ford 7.3L Power Stroke (1999-2003) :: 2001 - Rough Idle And Stalling?
A couple weeks ago my 01 7.3 with 265,xxx started ideling rough and stalling. I had driven in all day Sunday and the next day it started out of the blue! It would barely start idle rough and stall out no CEL. I have singed changed the icp, fuel filter and I have checked oil level. Also used fuel cleaner. Still had no luck. When I changed the icp sensor the check engine light came on and was no change I then got a ford oem camshaft sensor and my truck fired right up but still sounded like it had a little miss here and there drove it for a few weeks fine now back to the same thing it will start up and idle fine for 10 seconds then start the rough idle but won't stall out anymore just idle rough. I am stumped I can't get any codes to pull up and if oriellys uses there scan tool while the truck was running it would shut the truck off! I can't find any answers.
View 8 RepliesSanta FE SM (2001-06) :: Idle Really Low / Almost Stalling And Oil Pressure Light Flicker When Warmed Up
I bought the car 3 years ago 2003 2.4L Hyundai Santa fe , I have driven it around 200 miles ( to and from shops ), I am having an issue now where once the car is warmed up ( post 15 mins ) It will idle really low * almost stalling * and oil pressure light will flicker, If I hold the brake and get it to almost 800 - 1k RPM it goes off and driving is not an issue *no knock*. I just got it driving for the 1st time in the past year, and drove it for about 45 mins in stop an go traffic, Temp light was all the way to cold, once stopped in stop and go traffic it would go up half way, as soon as I could get above 50mph it would slowly work itself all the way to the bottom?
More Information
2003 2.4L Hyundai Santa fe
I should really count my losses and move on but I cant.
Bought the car with 89K on it I now have 90K
New Battery
New Radiator
New Motor mounts 3
New Trans mount 1
New Hoses
Oil Change ( 40 miles ago )
Trans Oil Change ( 40 miles ago )
Power Steering Fluid change ( 40 miles ago )
2nd cat delete ( didn't want to waste any more money )
After Market 1st Cat
Civic - Honda :: 1995 EX - Rough Idle / Stalling At Low RPMs And Won't Start When Humidity High
1995 Honda EX with 150,000 miles. Its been running rough ie rough idle, stalling at low rpms etc Additionally for awhile now when humidy reached north of 85% the car wont start. It cranks but rarely runs.
Took it to a mechanic last week for a tuneup. They replaced the Distributor cap, spark plug and wires and fuel filter. Car ran great for a day. Then progressively got worse. Was undriveable the other day stalling misfiring while at speed. Took it back today. They determined that it was still not getting spark and replaced the distributor. They did so, test drove it, declared it good and I came to pick it up. Paid the bill, walked out to the car and the damn thing would not start. Humidity was high.
Mechanic pulled a spark plug and put a tester in and didn't get a spark when cranking. He is assuming the distributor he just put in is bad. So they are keeping the car overnight to be fixed in the morning with a new distributor.
However I'm not convinced the dizzy is bad, I believe, as I've read that the Honda's ECU is probably bad and shorting out in the high humidity. Can a bad ECU would prevent spark?
Santa FE SM (2001-06) :: Jerking / Stalling - Need To Jump Start
Bought a 2006 2.4L Sante Fe a few months ago. Had a couple incidents of it jerking after descending the same hill in our neighbourhood. Have a 6 month warranty so brought it to mechanic. All their "scans" were showing everything working so they guessed at replacing the fuel pump and filter. A week later did the same thing but this time it stalled out and I had to jump start to get it back to garage. My wife scanned the internet and noticed other similar complaints. The crankshaft position sensor seemed to come up as being replaced in these incidences, and apparently the "scan" will not show it as failed if it is still somewhat operable. Based on that, we told the garage to replace it as they literally could not figure out what was wrong with the car, having driven it over several days for it to repeat the jerking and stalling we had experienced. It has only been a few days so here's hoping that was the answer.......
View 1 RepliesSanta FE SM (2001-06) :: V6 Rev Pretty Hard In Idle?
Just bought a 2004 3.5 v6 Santa Fe 140k miles. It's my first 21st century vehicle, the first time I've had one so computerized and all that. I'm really unfamiliar with many of the sounds it makes and what not. This runs nothing like my old Camaro or Dodge, what's normal or not.
She really seems to rev pretty hard in idle, especially when braked at a light while still in drive. Is this normal for a Santa Fe?
Ford Escape / Hybrid :: 2001 V6 Stalling When Driving - Hard To Start When Stops To Get Gas
I'm trying to diagnose an issue my sister has been having on her 2010 with the V6. Dealer can't find anything wrong with it
She says when she stops to get gas, it has trouble starting back. Will crank, but not start. has to try it several times. Sometimes pumping gas will work. (Sounds maybe like IAC to me)
She says when she's driving, that sometimes it will quit. Best I can understand from her description, it's when she's off the throttle. She says most of the time it will start right back up then.
She also says sometimes when she's trying to crank it back, it acts almost like a bad starter, or battery. Starter getting slower, then speeding back up. Also says that sometimes it acts like it's low on power. She has to floor it to make it go.
My thoughts are IAC or faulty fuel pump?
Santa FE SM (2001-06) :: Oil Leak And Rough Idle - CEL On
My 2001 Santa Fe is having some major issues with rough idling, and there is a fairly significant oil leak. The check engine light is not on. In the past year it has had a new fuel pump, fuel filter, valve gasket covers, spark plugs, spark plug cables, and transmission.
View 2 RepliesSanta FE SM (2001-06) :: Rough Idle - Oil Light Flickering
At idle, (600 RPMs, might need to bring it up?) the motor is Real rough, but doesn't stall out, just very "wobbly" Once the car is brought up to the 900-1000 RPM range everything flattens out, and at driving speeds it drives great! Pulled up to 90 mph on the high way, and passed a few cars on some back roads and everything ran great, until I hit idle.
It threw a code for the Cam Position Sensor after I tried to restart the car, and the person who work on this car before me had zip tied the connector into the sensor because he had broken it. Low and behold, you cant buy just the replacement part of the harness.
I tried to get the wires all plugged back in, and the CEL went away, but the idle was still pretty rough. Also, at idle, the oil light flickers just a bit.
Santa FE SM (2001-06) :: 2003 - Rough Idle When Using Brakes
2003 Sante Fe is suddenly having a problem at stop lights or anytime the car is stopped with brakes. It feels as if the car is going to stall - or back fire. Very evident since it pulls on the brake pedal - just had back brakes replaced.
View 1 Replies