Ford F-150 - 1997-2003 :: Stalling When Coming To A Stop
I've recently had problems with my truck running 97 f150 4.2L.The latest episode is it stalling when coming to a stop. It will start right back up, I've checked for codes and found none, I have changed the fuel and air filters and I have tested the fuel pressure.(I have a video of the test however I don't know how to upload it.) Key on engine off it pumps up to 30 immediately on the gauge. key on engine running gauge shows a steady 32. I am really at a loss for what to check next. I really need this truck dependable again ASAP my wife is scared to drive it.
View 11 RepliesGolf VI R :: Rough Running - Knocking Sounds Coming From Engine At Stop Light
I started my car this morning and drove to work. It's not that cold. I heard knocking sounds coming from the engine at a stop light. I lightly tapped on the accelerator to hear it better. My commute is short (3 miles), so I gingerly cruised there. I didn't try to accelerate and it didn't seem like I was suffering from loss of power either. I opened the hood and let it idol at work and couldn't really hear the knocking sound.
I downloaded the code when I got to work. After that I started the engine again and it sounded pretty normal. I'm due for my oil/filter change (~5500 miles).
Here are the codes. Any reasons to worry, or is this an one-time thing?
2 Faults Found:
001322 - Camshaft Adj. Bank 1 Intake
P052A - 001 - Cold-Start Timing not Reached
Freeze Frame:
Fault Status: 01100001
Fault Priority: 2
Fault Frequency: 1
[Code] ....
Ford F-150 - 1997-2003 :: 2001 - Rough Idle In Cold Weather
Have a 2001 F150 FX4x4 and since the weather changed and started having days below 40 the truck has started running rough for about the first 15-20 miles. When you first start it starts like normal for first 3-5 min and then it starts loping real bad like it has a cam in it!
View 5 RepliesFord F-150 - 1997-2003 :: 2002 - Running Rough And Check Engine Light On
My girlfriend has a 2002 F-150 with the 4.6 V8 and I was going to change the spark plugs for her. She said it started running rough and it threw a code and check engine light. She took it for a scan and they told her the number 5 plug was mis-firing. I'm fairly handy and bought a set of the recommended Motorcraft plugs from Rock Auto, AGSF32PM. It also matched the number in the owners manual so I thought I was pretty safe.
Funny thing, when I took the old ones out, they were AGSF22WM's instead. My thinking is they are a colder plug than the supposedly original equipment, but I don't think they've been changed before. They looked well used but the color was good. The truck has about 135K on it.
Long story short, and to get to the question(s), Would there be any reason the factory would have put a different plug in the engine than what is listed? Am I asking for trouble going with a hotter plug than what's been in there (pinging or timing retardation/loss of power)? Am I just overthinking the whole thing and need to put it back together and drive it?
Ford 6.0L Power Stroke Diesel :: 2004 Excursion Running Rough / Smoke Coming Out And Stalling
I have a 2004 Excursion with a 6.0 Bought the truck already studded, EGR deleted, and a 54V FICM. When I bought the truck it had a hot stall, no restart problem. Found the high pressure oil leaks and resealed them by replacing the #3 injector and replacing the top injector seal in the #4 .Oil pressure reads very good now and I drove the truck for a couple weeks problem free.
Truck started smoking (white to gray) and felt like it had a miss. No misfire or contribution codes. Truck failed the bubble test and I narrowed the leak down to the passenger side by removing the banjo bolt
Banjo bolt at the front of the passenger head
Found the #3 injector loose...the copper washer
Copper washer had disintegrated/melted and appeared to be stuck to the side of the injector. Scraped off easily enough, cleaned up the injector and injector cup and reinstalled the injector with new O-rings and copper washer.
Put the truck back together and still smoked the same and still felt like it had a miss. Ran KOER test and found sometimes a contribution code for #2 and sometimes #6 .
Drove the truck to work and it didn't feel down on power...mostly just smoked and rough idle...but on the way home there was a lack of power and just as I pulled into my driveway the truck stalled...wouldn't restart. FICM voltage was good, high pressure oil read over 900, IPR was holding around 40%.
Pulled the secondary fuel cap
Secondary fuel cap to run another bubble test...there was no fuel in it...completely empty. Started to think that I had a fuel feed problem. Hooked up a fuel pressure gauge
Fuel pressure gauge and drove the truck again...pressure wasn't great (45 lbs) but never dropped below 42...not even when it stalled. Pulled the cap again...dry again...yet the truck read fuel pressure.
Research showed that I was possibly pressurizing the fuel system with combustion pressure and that was possibly displacing the fuel from the fuel system. This would explain the run for a few minutes, then stall and no restart for a few minutes...I'm assuming that the pressure would bleed off and the fuel pump would start over.
Still failing the bubble test and still pointing to the passenger side. I pulled and recleaned the injector and cup...new orings
oRings and copper washer. Bubble test again...fail.
Pulled glow plug from #3 , failed bubble test still.
Pulled glow plug from #1 , failed.
Pulled #5 , failed...pulled #7 ...failed.
With no glow plugs in the passenger head I am still bubbling up to the fuel filter housing. Pulled the banjo bolt from the front of the drivers side head...no more bubbles.
Ford F-150 - 1997-2003 :: Check Engine Light Started Flashing / Running Rough Then Went Off
Ok on the way the my 1997 f150 4.6 L 180,000 check engine light started flashing and running rough and then the light went off, Also we took the Aftermarket Dynomax muffler off of it earlier today if that makes any difference, it still has the Cat Converter, New Plugs and Napa Wires.....
View 12 RepliesFord F-150 - 1997-2003 :: Running Rough Under Light Acceleration / Codes P0300 And P0301
Just got a 98 f150 w/ 5.4 4x4 excab. It idles fine but under light accleration. It starts bucking and missing bad, if I step on it, it down shifts and accelerates fine. If I try to maintain one speed it misses bad. It is not throwing any codes right now. The check engine light did come on for like a minute but went back off before I could have it read. I hooked up a scanner just to see if any codes were stored and got p0300 and p0301. I am going to clean the MAF and check for vacuum leaks. I hear the rear plug and coils can get water in them causing similar problems.
View 8 RepliesFord F-150 - 1997-2003 :: 2000 V8 Running Rough At Idle And Check Engine Light On
I started out with my 2000 F150 with a 5.4 V8 running rough at idle. It would idle way down slow and then rev up a little over and over. On a couple of occasions it would even die when in drive or reverse. I did finally get a Check Engine light so i put it on my diagnostic program to see what was up. Here is what I got:
P1151 Lack of HO2S21 Indicates Lean
P0171 System Too Lean Bank 1
p0174 System Too Lean Bank 2
After doing some reading up I checked all my vacuum hoses and cleaned my mass air flow sensor. I then got the same codes again after a few minutes of running. So I went to the next thing that was recommended, the upstream bank 2 O2 sensor. After changing it the truck ran fine for a couple of days, no issues. Then all of the sudden it idled a little funny again and I got a Check Engine Light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0300 Random/Multiple Misfire
I reset the light to see if I would get the same again later. Before the light came on again I filled my truck up with gas and it seemed to be running pretty good again. Then a day or so later it set the light again. This time:
P0171 Bank 1 Lean
P0174 Bank 2 Lean
P0136 O2 Circuit Malfunction Bank 1 Sensor 2
P0156 O2 Circuit Malfunction Bank 2 Sensor 2
P1131 Lack of Switches HO2S11 Lean
P1151 Lack of Switches HO2S21 Lean
I went ahead and drove for a few days as it had gotten really cold here and I didn't feel like messing around in my shop since it isn't heated. A couple days ago I needed gas so i filled up again. Suddenly the problem was gone again. Truck ran fine idled fine no missing or odd idling at all. That lasted a day or two before it started acting a little weird again. At that point i was down about 1/8 of a tank from full. I have read that there can be issues with the fuel pump.. I am kind of wondering if that may be it now. But I haven't had to deal with this sort of issue before so I am unsure what to check next. The truck always runs fine off idle, it only seems to have the issue when it is idling. I had reset the codes the last time and i have the light on again now. I haven't checked it yet but I am sure it is going be some combination of what i have had in the past.
I have read that the IAC valve can be an issue as well. I had a problem with mine sticking a couple years ago and when it would do it you could just tap it with a wrench and it would idle up. But it never died like it does now and it would also idle a lot slower than it does. Back then I cleaned the valve and had no more issues with it. The truck has always had times when it would act weird at idle usually after slowing down after being at highway speed. The current issue happens at all temps cold or hot.
Ford F-150 - 1997-2003 :: Idling Rough And Check Engine Light Came On After Running For About 20 Minutes
I replaced the heater core in my truck this weekend. The only thing I was worried about was pulling the dash. The truck is a 1998 f150 with the 5.4.. Everything went fairy well and decided to replace the AT Shift cable as well. Got everything put back. Truck runs, no leaks, no antifreeze smell. After running about 20 minutes, it started idling a little rough and my check engine light came on.
The codes are p0136, p0156, p1131, and p1151. I know these are related to the OS sensors. My question is could it be as simple as I miss an electrical connection when putting the dash back in? Was thinking possibly somewhere on the passenger side under the kick plate or possibly something while hooking up the heater hoses? Maybe even a ground that didn't get connected back when putting the das back in?
Ford F-150 - 1997-2003 :: Pedal Was Rock Hard When Hit The Brakes Coming To A Stop Light
I have a 1997 F250LD 4WD. I was driving and came to a stop light. I hit the brakes and the pedal was rock hard with what seemed to be very little travel. I pushed hard to get to a stop and the abs activated and I came to a slow stop. This has happened about 3 times over the last 1000 miles of driving. I see no ABS or Engine lights. Most of the time the brakes are normal. Pads are fine, fluid is fine. Brake booster seems to work fine, pedal is not mushy or hard to press other than the 3 or so times this has happened. Once this happens I can let off the brake and everything is normal. I have not found any vacuum leaks.
View 6 RepliesSanta FE SM (2001-06) :: Stalling And Running Rough - Codes P1166 And P1167
My 03 Sante Fe is running a little rough and is stalling. My Mechanic said this P code was going to run me $1300. I'm not very mechanical , but this just seems very high. He said that aftermarket sensors would not work and only Hundai parts for the fix.........
2003 Sante Fe, LX, 3.7 l engine
Ford 7.3L Power Stroke (1999-2003) :: E99 Stalling And Sometimes Running Rough - Codes P1280 And P1247
E99 Romps on start up and randomly dying. Bought this truck about 3 weeks ago. Previous owner mentioned he had issues with it getting hot and shutting off and not starting. Has new IPR, ICP and pigtail, I just put in a new fuel filter. Has 206k miles on it and is the 4R100.
The past two days after sitting all night I have been cycling the key twice and it hasn't done its romp. Typically when it does I can tap the pedal once and it goes away. This I could deal with but its started to die randomly while driving, never while cruising down the road. Its either just after starting it and rolling slowly or slowing down for a stop or to turn. When it dies, I can put it in neutral and it fires back up no problem. SES light usually comes on for about 10-15 seconds after but goes away.
Replaced the grey CPS that was in it with a dark grey one from RiffRaff Diesel. Got a Edge CTS2 to figure out the problem, the codes Im getting are P1280 and P1247.
The ICP pigtail they replaced they spliced on with butt connectors. I plan on pulling it to check for oil and make sure it does look new and redo the connections with solder then shrink wrap them.
I was told to check the IPR% under full throttle which I did and it never went higher than 36.7
The truck did start running rough around 45-50 mph and I did get a video of the ICP jumping around while cruising down the road.
Then I went through a drive through and the truck kind of hiccuped like it wanted to stall and the ICP went right to 725 PSI and idled up and stayed there until I started to leave.
Truck is pretty much stock, K&N air intake and muffler cut out and straight piped.
Here is a link to the videos I got :
e99 7.3 ICP fluctuation while driving - YouTube
e99 ICP steady at 725 PSI after acting like it wanted to stall. - YouTube
Ford F-150 - 1997-2003 :: Runs Rough And Stalls When Stop Or Rolling To A Stop It Would Die
I am having trouble with my 1998 F-150...XLT Triton? I bought the wrong motor for it and installed it, turn out it's a 1999 Windsor 5.4
Problem is that it runs rough and stalls when I stop or rolling to a stop it would die.... It seems ok while cold, but when driven for 20 minutes or more it does it.
I have used original 4.6 harness as well as original spark plug coils and only replaced throttle body, oil filter holder thingy mount, exhaust manifolds are from 4.6.
When the throtle body was on the 4.6 I didn't have when the motor ran. Only misfire due to intake manifold leaking into the 3rd cylinder spark plug.(I thought it was a bad head gasket and changed in....installed the timing chain wrong and messed up the whole motor)
Also I broke a rear brake line and now it only has front brakes and smells like fried transmission oil.. This is my first truck and first truck accidental engine swap. Also the 5.4 Intake manifold is missing 2 coolant sensors and it's giving me the P0118 ECT Sensor Circuit High input...
Toyota - Corolla :: 1997 - Rough Idle / Stalling Noises While Stuck In Stop And Go Traffic
I have a 1997 Corolla with 150k miles.
I had my catalytic converter and flex pipe replaced this summer. Lately, my car has been idling rough. While stuck in some horrific stop and go traffic three weeks ago, it started to make noises as if it would stall out. It didn't, but it still sometimes makes those noises.
The car seems fine on the highway. No loss of power. I did think that the hood felt too warm on a recent trip, but the temperature gauge in the car showed no issue.
The car hesitated when I tried to start it last week, but normally starts fine. It was the first cold day of the year.
I saw some white smoke come out of the tailpipe last week. It only happened once. Coolant and oil levels are fine. The spark plugs look good.
The fill pipe has been leaking gas for several months. It leaks if the tank is more than half full and it drips a bit of gas when I fill up. Two mechanics have not been able to find the leak and have told me not to replace it until it is a problem, given the age of my car.
I took it to a mechanic today (not the one who replaced the cat). He told me that the rough idling is due to the new flex pipe being shorter than what was originally there. He assured me that the car is fine to drive long distances and that there was nothing wrong with it. There's no check engine light or anything on the dash to indicate a problem.
I should be relieved, but I'm not. I've lost confidence in my car. Can the stalling noises and rough idling be explained away by a changed exhaust system? Or are these signs of a problem about to happen?
Golf IV / Jetta IV :: 2003 GLI 24v VR6 Running Rough And Stalling Out
I have been beatingy head against the wall for the last month with this car. It started out by just running really rough and stalling out. Found out that I had a bad clamp on the air intake that attaches to the throttle body. Replace that after I already replaced the MAF. Everything was great till couple days later then the car just crank crank crank no fire....
I cleaned the grounds pulled the plugs and coils, had perfect spark. Put everything back come to find out after going thru my Bentley manuals I jumped around the fuel pump relay fuel pump kicked on perfect started great! Replaced the fuel pump relay BAM! Ran great!!!! For 2 days..... After that right when I pulled into the drive way the car would not start.... So I tried everything again.... To no avail..... Check the codes again, now I'm throwing these codes which yes I did cross reference in my Bentley manual.
P1117- O2 sensor heater circuit bank 1 sensor 2 short to ground
P1198- O2 sensor heater circuit bank 1 sensor 2 electrical malfunction
P1472- EVAP emission control LDP circuit short to ground
P1516- Intake manifold changeover valve circuit open
And the dreaded same code I've had the whole time........
P0102- Mass or volume air flow circuit low input.
I have also tried tracking down any bad wires, and testing resistance...
Jeep - Grandcherokee :: 2001 4.0L Started Stalling When Coming Up To A Stop
I have a 2001 Grand Cherokee 4.0L with 215xxx miles. It just started stalling coming up to a stop, but then it starts right up no problem. Engine idles a little rough and the gas mileage has gone down somewhat. The CEL came on a while ago, and the auto shop checked the computer code and said it was the neutral safety switch. I brought this up with a friend who had the same problem and he rebuilt his and said it was easy. So I was going to attempt it, but I can't find the darn thing. @ questions:
1)where is it? and
2)could the NSS be causing the stalling?
Ford F-150 - 1997-2003 :: 2001 - Code PO1747 - Engine And Overdrive Light Blink And Acts Like Running Out Of Fuel
2001 F150 5.4 Auto ... Truck was running excellent. Engine light and overdrive light begins to blink and it acts like its running out of fuel or water in gas. Baring made it home. Cleared the code and it comes back. Transmission seems fine.
View 2 RepliesFord F-150 - 1997-2003 :: Exhaust Leak Cause A P0171 Code / Idling Rough And Almost Stalling At Red Lights
It's been a long time since I have posted here mainly because my truck was wearing a bow tie for awhile. But my wife was nice enough to tell me the Bow Tie wearing truck was making a funny noise on New Years Day (seems a small drum corps took up residence in the oil pan). So anyhow now I am back in a real truck . My new to me 1998 F150 5.4 Liter ran fine until yesterday. It started idling rough and almost stalling at red lights. about halfway home the CEL light came on and is throwing a P0171 code.
So far I have checked for vacuum leaks including all the elbows on the PCV system' tried the spray test with a can of flammable break fluid and a can of starting fluid (man I love the smell of that stuff) could not find a leak. Cleaned the MAF sensor and the K&N air filter (not a fan of these) IAC seems to be working. Only thing I know that is leaking for sure is the driver side exhaust after the cat. But that is the wrong bank if I am correct on which bank is which.
So why only one bank running lean and why does it act like it is only firing on 4 cylinders?
Ford 7.3L Power Stroke (1999-2003) :: 2001 - Rough Idle And Stalling?
A couple weeks ago my 01 7.3 with 265,xxx started ideling rough and stalling. I had driven in all day Sunday and the next day it started out of the blue! It would barely start idle rough and stall out no CEL. I have singed changed the icp, fuel filter and I have checked oil level. Also used fuel cleaner. Still had no luck. When I changed the icp sensor the check engine light came on and was no change I then got a ford oem camshaft sensor and my truck fired right up but still sounded like it had a little miss here and there drove it for a few weeks fine now back to the same thing it will start up and idle fine for 10 seconds then start the rough idle but won't stall out anymore just idle rough. I am stumped I can't get any codes to pull up and if oriellys uses there scan tool while the truck was running it would shut the truck off! I can't find any answers.
View 8 Replies