Elantra XD (2001-06) :: Running Rough Like On 3 Cylinders
Friend of mine has a 2001 Elantra, not sure of the mileage but it started running really rough, like it's on 3 cylinders. His mech wants to look at the head, thinks there's a broken spring or something.
I asked if the timing belts ever been changed, no it hasn't. My suggestion is it might have lost a few teeth from the belt and jumped. I can't see it being a broken valve spring or something worse because the beta engine are tough as nails.
He said the wires are fine, they probably need replacing too because my friend is the type of person who changes oil and that's it.
Santa FE SM (2001-06) :: Power Lost And Stalled While Driving - How To Fix It
Driving along, suddenly lost gears, engine revved a slight bit then lost power and stalled, the engine turns over but will not start but when it turns its in a lower key sound, the timing belt is in place but has recently been changed, would you think it has slipped? Seems a total lack of combustion in the top of the engine, would a slipped timing belt cause this?
View 4 RepliesSanta FE SM (2001-06) :: Gas Mileage Decrease - Lost Around 4 MPG In City Driving
My 03 2.7 has suddenly lost around 4 MPG in city driving. Haven't taken it out on the highway to know where that is at. Used to get around 20/21 and now I'm around 16/17. Mileage is at 97k now and has new spark plugs and brakes done recently. I know the brakes are not dragging. All the fluids are fairly new and the car drives the same as before, I can't feel a difference in performance. Just lower gas mileage. I haven't changed out the T-stat yet, but the temp gauge in car reads the same as always. I checked the car with a code checker and there are no pending codes. I know this is the age where the oxygen sensors could start to go bad and have never replaced them.
View 12 RepliesSanta FE SM (2001-06) :: Lack Of Power / Rough Running
Well today I have moved on to the next project on my 02 v6 4X4 Santa Fe, which is the rough running. When I got the car, it had CEL with codes for misfire #5 and lean condition codes. I noticed the wires were in need of replacement (one had black tape wrapped around it) so changed the plugs and wires. The 2 hoses, one that goes between the valve covers on the pass side and the hose between the valve cover and throttle body on driver side were both cracked so replaced them along with a few other vacuum lines, just because I had access to them. Cleared the codes and it still runs like crap, but after 112 miles, town and highway driving, there are no CEL codes. When its first started it idles at 1500 and sounds like its missing and has very little power going down the road. When it warms up seems to run a bit better but still nowhere close to what it should. Equal compression on all 6 cylinders and has power to all 6 injectors and tested to be sure there was a pulse to them as well. Coil packs all tested well. the exhaust is in bad shape and don't know if that would have any effect on how its running.
View 6 RepliesSanta FE SM (2001-06) :: Engine Running Rough When Started / Backfire When Give It Gas
I have a problem with my 01 santa fe. When I start it the engine runs rough and when u try to give it gas it pops or backfire through throttle body and air intake tube? Checked the timing belt its ok hasnt slipped.so im stuck at this point.
View 8 RepliesSanta FE SM (2001-06) :: Stalling And Running Rough - Codes P1166 And P1167
My 03 Sante Fe is running a little rough and is stalling. My Mechanic said this P code was going to run me $1300. I'm not very mechanical , but this just seems very high. He said that aftermarket sensors would not work and only Hundai parts for the fix.........
2003 Sante Fe, LX, 3.7 l engine
Santa FE SM (2001-06) :: 2.4L Engine Running Rough / Rich Smell All The Time
When firing up the engine cold it runs really rough, smells very rich all the time, even warmed up. No codes set, fuel trims are within 5-10%. I've replaced the front O2 sensor, swapped crank & cam sensors, Map sensor (have lots of spare parts) & I'm sure there was more things I've changed but can't remember. I have a snap on scanner and everything is within parameters.
I have not checked the EGR valve or solenoids yet. It's a 2006 Santa Fe 2.4l 5 speed, new timing belt & balance belt replaced when I dropped this engine in. Is there a common problem with these that I could begin looking for?
Santa FE SM (2001-06) :: Engine Running Rough At Idle / High RPM And Appears To Be Misfiring
Recently replaced plugs/wires on soon-to-be 10 year old '04 SF 3.5L (157K mi.) for the first time.
Plugs were OE Champion Platinum and all 6 looked identical except for excessive gap of .010 +/- due to all the miles. Replaced plugs with same as OE. Old plug wires looked good, but replaced them with aftermarket wires ( fit was as good as OE). Also replaced plenum gasket.
Problem is: engine runs rough at idle and high rpm and appears to be mis-firing. CEL is off and code reader shows no Trouble Codes stored.
Santa FE SM (2001-06) :: 2004 2.4L Engine Running Rough And Shakes After Timing Belt Replacement
I recently replaced timing belt and balance belt on my 2004 santa fe 2.4l and now the engine runs like crap and shakes badly. I went over all timing marks again and again and I am at a loss.
View 9 RepliesGolf IV / Jetta IV :: Running Rough And 3 Codes Stored - Cylinders 2 And 3 Misfire
So my daughter's 2000 Golf Mk4 with 160,000 miles on it was running rough and had 3 codes stored - cylinders 2 & 3 misfire and a 411 secondary air injection problem.
Having had the misfire code before I swapped injectors around and the error code moved cylinders with the injectors so I attempted cleaning them and also cleaned the throttle body and intake manifold. At this point car still running rough but also started smoking badly.
Replaced the following items:
- Spark plugs
- Spark plug wires
- PCV valve
- PCV hose
- Fuel injectors w/ remanufactured
Hose reconnected between secondary air injection pump and air intake - previous owner had duct-taped it in when he couldn't get it to seal I guess. I've never heard it run.
Car running better, idles more smoothly, doesn't stumble or stall like it did before, no error codes coming up BUT car smokes a lot and the fumes make me feel sick just driving it a mile.
The car had never smoked like this before, hasn't had a whole lot of love the last year or two but no real problems either so why the sudden smoke?
At first I assumed it was cleaner being burned off but that should have been gone in under a minute and this is on-going. It's bad enough to not only be embarrassing but apparently dangerous as the fumes are bad.
Ford 7.3L Power Stroke (1999-2003) :: Truck Running Rough And On Less Than 8 Cylinders
I had an HPOP line burst and soak the engine compartment with oil. I replaced the line and degreased the engine and rinsed it off. I started the truck and let it idle for 15 minutes or so before driving it. On the way home right after a shift it started chugging and running terribly. The check engine light was on as well. I limped it the mile or so home and shut it off. I restarted it and it runs just fine. I checked the DTC's with Forscan and there were a bunch of things that were mostly related to the HPOP and the MAT sensor that was shredded when the line blew. I left the hood open to dry out today and I'm hoping it is just some water in a connector. Does that sound plausible?
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 Running Rough / Misfire On Cylinders
I have a buddy at work who has an 04 f350 6.0 that is running very rough. we put a scanner on it and disabled the injectors and 1,7,8 have no change. He checked the FICM voltage and is getting 48 volts on crank and run. He checked the wiring for anything loose or rubbed but nothing seems wrong.
View 14 RepliesFord Super Duty (1999-2016) :: F350 Running Rough Like On 4 Cylinders After Start Up
1999 F350 & lately if I don't plug it in even if it's like 40 out for like the first 30 sec sounds like its only running on 4 cylinders than it'll just even out & alls good. thinking glow plugs here. I did replace them last fall unfortunately with the cheep ones that I been now reading bad things about.
View 2 RepliesSanta FE SM (2001-06) :: How Cylinders Are Numbered
How the cylinders are numbered in the 2.7 V6? I have a misfire code for cylinder #4 (304) and might need to know which cylinder is #4. I've replace all six plugs and wires, no change. Thinking about the coil pack. I hate just changing things without some indication they are bad.
View 4 RepliesAudi - A4 :: 2001 - Misfire On All Cylinders And Car Appears To Be Running Lean
I have a 2001 Audi A4 1.8t (AWM engine, B5 platform). When I start the car, I get misfires on all cylinders (very rough idle, sometimes it stalls when the engine is cold) and the car appears to be running lean. Once the CEL comes on, it runs fine (albeit the slight loss of power do the ECU going into limp mode to correct the problem).
So far, I've done the following myself: new O2 sensors, new SAI pump, new EGR valve, new diverter valve, new N75 valve, new vacuum hoses, cleaned the throttle body, new MAF sensor, cleaned the air filter, new plugs, and new coils. When the problem persisted, I had my mechanic change the timing belt, check for vacuum leaks, change the valve cover gasket, replace the fuel pump and filter. None of this has solved the problem! This is driving me nuts.
At this point, there are only two possibilities that I can think of:
1) Catalytic converter is clogged? I pulled out the pre-cat O2 sensor, started the car, but it still misfired. This seems to mean that there's another problem (i.e., if the cat is clogged, it's in addition to something else).
2) Dirty fuel injectors? I've put two bottles of Techron through the car to no avail. From the outside, they look pretty dirty, so I'll definitely try removing them, cleaning them, and replacing the gaskets. Hopefully this solves it.
Is there something I'm missing?
Golf IV / Jetta IV :: 2001 VR6 GTI - Idles On 3 Or 4 Cylinders / Runs Rough
2001 VR6 GTI....
Already done:
Replaced the coil pack and plugs
Measured resistance of plug wires (all at about 6K Ohm)
Replaced front O2 sensor
Replaced purge solenoid valve
Replaced coolant temp sensor
Replaced fuel filter
Replaced fuel pressure regulator
Replaced MAF sensor
Cleaned the throttle body
Cleaned the throttle position sensor
Ran a tank of seafoam treatment (injectors were new 6 mos ago.)
Checked running voltage of battery
It was smoking and stinking bad with a rich mixture. It improved with the MAF change but still runs like a farm tractor. Now it idles on 3 or 4 cylinders, runs rough through 3000 RPM then runs cleaner at above 3000 RPM, but only at light throttle. CEL is either on or flashing when driving.
Don't know what to do next - nice car not fun to drive like this. What this could be and how to test it?
Chevrolet - Silverado :: 1999 - Running Rough / Popping / Backfiring And Lost Power
My wife was driving the 1999 K3500 7.4 model ls crewcab truck home the other day and out of the blue it started running rough popping and back firing and lost power. It had a major tune up about 40,000 miles ago. It sometimes has a hard time cranking to start, but once it starts it idles really rough and pops and smells like it is running rich. I thought the distributor cap but it looks fine, could it be a sensor?
View 2 RepliesFord Excursion :: 2001 V10 Not Running On All Cylinders / Check Engine Light Is Not Coming On
Bought a fixer upper 2001 v10 and it's definitely not running on all cylinders. Also the check engine light is not on and the PCM is not saying it's on (per my code reader) and it doesn't come on when I turn the key on.
Is it possible the previous owner had a programmer of some sort to disable the CEL? If the bulb were removed my scan tool would still show it on. Trying to get it to tell me which cylinders I am having trouble with.
Ford 7.3L Power Stroke (1999-2003) :: 2003 - Running Rough / 2 Cylinders Not Working Correctly
I have a 2003 F250 7.3L. I put new injectors in my truck four months ago and all of a sudden, I have 2 cylinders not working correctly, making the truck to run really badly. I sent the 2 injectors from the bad cylinders back for warranty and they replaced both of the injectors but nothing was wrong. I put them in and the truck still runs badly. I have a new fuel filter, new ICP, new CPS and glow plug relay. I cannot drive the truck, it smokes white at idle. I can unplug each injector at a time and cyclinder 5 does not change how the truck runs
View 14 Replies