Ford Super Duty (1999-2016) :: Lift / Leveling - Clunk Every Time When Turn To The Right
Put in 2.5" leveling blocks under front coil springs. Now I hear a clunk nearly every time I turn to the right. Why this might be?
View 3 RepliesFord Super Duty (1999-2016) :: No Full Turn Right After Lift Kit
So last week I installed a 6" lift and once we got it done I could barley turn right at all. So I decided to put a drop pitman arm on yesterday with a buddy, thinking that was the issue. But I still have the problem, and I very badly need to fix it and don't know what it is. Turning left is completely fine however. It feels like I'm trying to steer an 18 wheeler right now.
View 6 RepliesFord Super Duty (1999-2016) :: Tires Upgrade With No Lift?
Looking to upgrade my tires and would like to go a hair bigger but nothing radical. I have the 20's now, what's the biggest size I can go to with no lift.
View 2 RepliesFord Super Duty (1999-2016) :: 2008 - Lift Kit Doesn't Sit Level
I have a fabtech 4 link 6" lift on a 2008 6.4. The lift kit used to sit level but the front is sitting lower now. How can I fix this?
View 10 RepliesFord Super Duty (1999-2016) :: Rear End Shudder / Vibration After Lift Installed
So I'm getting a mild to severe shudder depending on load and acceleration rate from stop to 10-15mph... It's worse if I'm on an incline...This has started since having a lift installed...I'm guessing it has everything to do with pinion angle...right?
1999' F350 7.3L 4x4
Crew Cab Long Bed
Ford Super Duty (1999-2016) :: Front Drive Shaft Angle After Lift
I finally got my lift installed the other day from PMF. My question is how do I get my pinion angle corrected on the front drive shaft? I know Trevor sells a Tcase clocking adapter may have to go that route IDK Unlike the rear there's only so much pitch you can put on the front axle until it causes issues with steering. I was thinking of going with an aftermarket front drive shaft designed to handle harsher angles.
I live in the mountains and after installing the lift and pulling a trailer on some of theses steeper gravel roads I can feel a harshness or something coming from under to front of the truck. I'm unable to post pics since I'm back on the road but I can visually see the front drive shaft angle is definitely not in line like it was.
I'm currently running PMF 2.5 alpha with a 1'' spacer and 3 link kit up front and 5'' progressive leafs and traction bars out back. I was able to fix my rear shaft angle using shims on my carrier bearing ( not really a big fan having 1 1/2'' of stacked shims BTW ) ....
Ford Super Duty (1999-2016) :: 2002 - Adding Suspension Lift Kits?
I have a 02 f250 powerstroke and I wanna put a suspension lift kit on it I wanna go with a 6 inch lift but I'm afraid if I go any higher than a 4 inch I'll have to change to much. What I would have to change and if I would have to extend any of my brake lines also the truck is a cab and a half with an 8 foot bed so I do have a carrier baring on the drive shaft would I have to change anything with that?
View 14 RepliesFord Super Duty (1999-2016) :: How To Lift Suspension To Change Out Spring Bushings
2003 f250 6" lift on 35s. How to lift the suspension to change out spring bushings? Was thinking using two chain falls on tow hooks on the front, any easier, safe, cheaper way. I have a farm jack but need to weld a plate on bottom of it for more support...
View 5 RepliesFord Super Duty (1999-2016) :: 2008 - Hood Won't Stay Up - Lift Cylinders?
I got to replace mine because the hood won't stay up on it's own and is heavy to lift. I was wondering if these things fail often. Mine is an '08.
View 5 RepliesFord Super Duty (1999-2016) :: Where To Put Jack Stands When Installing Front Lift Shackles
When installing front lift shackles, do you place jack stands under the axle, or the frame? I can't really find an answer. I assumed the axle, but i saw a thread and from what i could see it looked like it was supported at the frame and the axle was hanging free in the air. Just want to be sure before i start unbolting the stock shackles tomorrow and kill myself.
View 14 RepliesFord Super Duty (1999-2016) :: Loud Squealing Sound On Driver Side / Lift Pump?
Truck details:
2008 f350 6.4 290,000 klm
DPF and full EGR delete
K&N intake
IDP custom street tune
Loud squealing noise that happens when cold or at temp.
2000 to 2500 rpm's to 3000 rpm then it goes away
Happens only when accelerating over 50% anything under and the noise doesn't happen.
15 to 20 pounds of boost
Turbo sounds good
No codes
All plumbing looks sealed and tight
Fuel coolant res is full and clean
I'm thinking it could be the lift pump dying or having trouble supplying the fuel demand. Started after I did the cold air intake....
Ford Super Duty (1999-2016) :: 2004 - Loud Rattle Under The Hood When Lift Off The Accelerator Pedal
I bought a 2004 F250 super duty 4x4 with the 6.0 a couple weeks ago and have a few questions. Hopefully all of these things are normal, but I thought I would ask you experienced drivers.
1) Occasionally while driving when I lift off the accelerator pedal I can hear a sort of loud rattle under the hood. I assume this is the turbo shutting down? Is that normal?
2) 4x4 and locking hubs... I have the 4x4 hi and low switch on the dash. Do I need to also manually lock the hubs to go into 4x4? After reading the manual it seems like I can just turn the dash switch and they should automatically lock, but I'm not sure. The hubs are not marked, but going by the pictures in the manual I think I know which is "lock" and which position is "auto" or off.
3) Front wheels hop at full turn. I expected wheel hop in 4x4 or with the hubs locked, but even in 2WD with the hubs in the auto position the tires still "hop" or knock a bit at sharp turns. Is this normal?
Ford Super Duty (1999-2016) :: F250 - Raising Front - 3 Inch Lift Spindles Work Fine?
want to raise the front of my 99 f250 super duty. I only found rough country for my options. I am looking for a 2-3" lift. Will the 3" lift spindles work fine? What else am i going to need? Shocks?
[URL].....
Ford Super Duty (1999-2016) :: Trailer Brake Controller Install
I've just bought a new 2016 SD xlt. The only extra I wanted that is missing is the factory trailer brake controller. The dealer told me it had to be programmed. I was expecting plug and play and planned to do it myself till they told me that. Is this true?
View 14 RepliesFord Super Duty (1999-2016) :: Upfitter Switches Relay Install
I want to install a set of upfitter switches but my truck didn't come with them...so I bought the switches and the relay/wire harness as well...I cannot find any good information on where to mount the relay and where an extra plug on that harness goes too. I have found the wires that attach and go through the firewall but I am not sure where the rest of this mess goes...my truck did not come with the wire harness already installed...
View 4 RepliesFord Super Duty (1999-2016) :: Install Pics For SCT Livewire 5015
My dad is looking to purchase a tuner from 5-Star for his 01 Super Duty. He's leaning towards splurging on the Livewire 5015. I know the unit comes with a suction cop, but I was curious if anyone has come up with something cleaner. I searched, but didn't find anything.
Any install pics or ideas?
Mike
Ford Super Duty (1999-2016) :: Bilstein 5100 Shocks Install?
I just purchased 4 front and 2 rear Bilstein shocks for my F350 and will be installing them today, but my question is I have seen them mounted 2 ways (With the rubber boot up and also inverted) which is the correct way?
View 5 RepliesFord Super Duty (1999-2016) :: 2011 - Nav Install - Camera Redirecting?
I have recently upgraded the factory sync system in my 2011 f350 lariat to a factory sync with NAV. I am looking for tha way to redirect the fideo feed to the rear view mirror to the nav system, I have found the wire coors and pin locations for the radio end, just need the info if there is a way to move it in the a pillar harness on the passenger side to the radi harness.
Did ford really put 2 different harnesses in the cab if you had nav or not? Factory nav unit and factory camera (camera was in the vehicle to begin with). the radio side is pin 1 and 6 on the 10 pin radio harness.
Ford Super Duty (1999-2016) :: Plow Mount Brush Guard Install
So I've had this WAAG brush guard laying around for a few years and figured it was time to do something with it. Of course it was bought with no mounting brackets. I had found a lower gear from a Fisher MM1 plow. Tossed the in the truck and started from there.
Broke out the cherry picker and started lining stuff up. Drilled some holes and bolted it up. It's all bolted up but I still need to take a piece of 2x3 angle and weld it to the lower plow mounts to tie the bottoms together and create a step.