Ford Super Duty (1999-2016) :: 2004 - Loud Rattle Under The Hood When Lift Off The Accelerator Pedal
I bought a 2004 F250 super duty 4x4 with the 6.0 a couple weeks ago and have a few questions. Hopefully all of these things are normal, but I thought I would ask you experienced drivers.
1) Occasionally while driving when I lift off the accelerator pedal I can hear a sort of loud rattle under the hood. I assume this is the turbo shutting down? Is that normal?
2) 4x4 and locking hubs... I have the 4x4 hi and low switch on the dash. Do I need to also manually lock the hubs to go into 4x4? After reading the manual it seems like I can just turn the dash switch and they should automatically lock, but I'm not sure. The hubs are not marked, but going by the pictures in the manual I think I know which is "lock" and which position is "auto" or off.
3) Front wheels hop at full turn. I expected wheel hop in 4x4 or with the hubs locked, but even in 2WD with the hubs in the auto position the tires still "hop" or knock a bit at sharp turns. Is this normal?
Ford Super Duty (1999-2016) :: 2008 - Lift Kit Doesn't Sit Level
I have a fabtech 4 link 6" lift on a 2008 6.4. The lift kit used to sit level but the front is sitting lower now. How can I fix this?
View 10 RepliesFord Super Duty (1999-2016) :: 2008 F350 - Auto Hubs Won't Stay Locked
2008 F350 hubs wont stay locked in when in auto position. everything stays locked while in manual and 4x4 works fine, but in auto the hubs wont stay locked while spinning. I was trying to find the problem when i noticed that one hub stays locked all the time and the other locks and unlocks as it should but it wont stay locked while spinning. My question is do I have two bad hubs or is their a leak that wont let the hub stay locked? Also on the hub that wont unlock is this a leak problem as well or a internal problem?
View 5 RepliesFord Super Duty (1999-2016) :: No Full Turn Right After Lift Kit
So last week I installed a 6" lift and once we got it done I could barley turn right at all. So I decided to put a drop pitman arm on yesterday with a buddy, thinking that was the issue. But I still have the problem, and I very badly need to fix it and don't know what it is. Turning left is completely fine however. It feels like I'm trying to steer an 18 wheeler right now.
View 6 RepliesFord Super Duty (1999-2016) :: Tires Upgrade With No Lift?
Looking to upgrade my tires and would like to go a hair bigger but nothing radical. I have the 20's now, what's the biggest size I can go to with no lift.
View 2 RepliesFord Super Duty (1999-2016) :: Rear End Shudder / Vibration After Lift Installed
So I'm getting a mild to severe shudder depending on load and acceleration rate from stop to 10-15mph... It's worse if I'm on an incline...This has started since having a lift installed...I'm guessing it has everything to do with pinion angle...right?
1999' F350 7.3L 4x4
Crew Cab Long Bed
Ford Super Duty (1999-2016) :: Front Drive Shaft Angle After Lift
I finally got my lift installed the other day from PMF. My question is how do I get my pinion angle corrected on the front drive shaft? I know Trevor sells a Tcase clocking adapter may have to go that route IDK Unlike the rear there's only so much pitch you can put on the front axle until it causes issues with steering. I was thinking of going with an aftermarket front drive shaft designed to handle harsher angles.
I live in the mountains and after installing the lift and pulling a trailer on some of theses steeper gravel roads I can feel a harshness or something coming from under to front of the truck. I'm unable to post pics since I'm back on the road but I can visually see the front drive shaft angle is definitely not in line like it was.
I'm currently running PMF 2.5 alpha with a 1'' spacer and 3 link kit up front and 5'' progressive leafs and traction bars out back. I was able to fix my rear shaft angle using shims on my carrier bearing ( not really a big fan having 1 1/2'' of stacked shims BTW ) ....
Ford Super Duty (1999-2016) :: 2002 - Adding Suspension Lift Kits?
I have a 02 f250 powerstroke and I wanna put a suspension lift kit on it I wanna go with a 6 inch lift but I'm afraid if I go any higher than a 4 inch I'll have to change to much. What I would have to change and if I would have to extend any of my brake lines also the truck is a cab and a half with an 8 foot bed so I do have a carrier baring on the drive shaft would I have to change anything with that?
View 14 RepliesFord Super Duty (1999-2016) :: How To Lift Suspension To Change Out Spring Bushings
2003 f250 6" lift on 35s. How to lift the suspension to change out spring bushings? Was thinking using two chain falls on tow hooks on the front, any easier, safe, cheaper way. I have a farm jack but need to weld a plate on bottom of it for more support...
View 5 RepliesFord Super Duty (1999-2016) :: Lift / Leveling - Clunk Every Time When Turn To The Right
Put in 2.5" leveling blocks under front coil springs. Now I hear a clunk nearly every time I turn to the right. Why this might be?
View 3 RepliesFord Super Duty (1999-2016) :: Clunk After Lift Install At Low Speed Or When Stopped
Just installed a 4" lift sunday, with a BDS drop pitman arm and then i retorqued it to 185 ft/lb. I now have this extremely low speed (<2mph) or stopped clunking whenever i turn the wheel. I just replaced the upper and lower tie rod that goes from the pitman arm, and its still doing the same thing. Steering box is shot?
Clunk after lift install - YouTube .....
Ford Super Duty (1999-2016) :: Where To Put Jack Stands When Installing Front Lift Shackles
When installing front lift shackles, do you place jack stands under the axle, or the frame? I can't really find an answer. I assumed the axle, but i saw a thread and from what i could see it looked like it was supported at the frame and the axle was hanging free in the air. Just want to be sure before i start unbolting the stock shackles tomorrow and kill myself.
View 14 RepliesFord Super Duty (1999-2016) :: Low Injector Circuit On All 8 Cylinders
2006 6.0 superduty showing low circuit codes on all 8 cylinders so i checked the FICM and it has 48v when key is on and while turning engine over. What to check next?
View 11 RepliesFord Super Duty (1999-2016) :: F250 V10 - 2 Misfiring Cylinders
I just bought a 99 F250 Super Duty with the V10. When I bought it, I knew it had 2 misfiring cylinders (4 and 10) because it was throwing P0304 and P0310 (only 2 codes), but wasn't concerned as I've had to take care of my wife's Escape with it's misfiring cylinders. I replaced the 2 coils and replaced the plugs with Motorcraft plugs from O'Reilly's, cleared the codes and she ran fine for a couple of days. Now I'm getting an intermittent misfire, it's only occasionally throwing a pending code of P0300 which is "Multiple Random Misfire".
I'm fairly certain it's an issue on the electrical side because if it were an issue with the injector or injectors it would be constant regardless of RPM... right? As it is now, it basically does it between 55-65 while in overdrive trying to pull a hill or slightly accelerate. Once it's shifted out and the RPMs go up to 2k+ it runs like a champ... and it kills my fuel economy. The way it's behaving is just like when a coil is bad, but it's saying it's not identifying a specific cylinder (saying it's multiple) and it doesn't always do it (about 60% of the time).
I checked the MAF and it's very clean (looks almost new), checked the vacuum lines (those I found without a manual) and couldn't find any leaks and when I changed the plugs all the plug wells were dry.
Ford Super Duty (1999-2016) :: 2011- Misfiring On All Cylinders?
SO this truck came into the shop yesterday with a really bad misfire. pulled the codes and got a misfire codes for cylinders 1-6 and also p1450 (unable to bleed fuel tank vacuum) and p068a (pcm/ecm power relay de-energized too early) i found a TSB related to the issue, TSB 10-25-7 i did as the tsb told me to do and pulled valve covers to check out the rocker shaft rollers and inspect for any signs of surface deformation or fatigue. they were fine on both sides.: ive got spark in all cylinders. fuel pressure was right around 55-60 the gauge was fluctuating pretty good. checked for bad fuel or water in fuel ect. fuel seems to be good. pulled O2s incase of plugged cats still ran like crap.
View 13 RepliesFord Super Duty (1999-2016) :: Loud Squealing Sound On Driver Side / Lift Pump?
Truck details:
2008 f350 6.4 290,000 klm
DPF and full EGR delete
K&N intake
IDP custom street tune
Loud squealing noise that happens when cold or at temp.
2000 to 2500 rpm's to 3000 rpm then it goes away
Happens only when accelerating over 50% anything under and the noise doesn't happen.
15 to 20 pounds of boost
Turbo sounds good
No codes
All plumbing looks sealed and tight
Fuel coolant res is full and clean
I'm thinking it could be the lift pump dying or having trouble supplying the fuel demand. Started after I did the cold air intake....
Ford Super Duty (1999-2016) :: 2009 F250 5.4L - 2 Misfiring Cylinders
I have a 2009 f250 with 5.4l 3v. have had the truck only about 6 months. it started missing about a month after I got it. I replaced all 8 cops and all 8 sp. The truck ran excellent until 11/29, then I got a cel and the truck started running really bad. Found 3 misfiring cylinders. Changed all 3 cops again and that did nothing. Pulled the injectors and found 2 of them were clogged, replaced those also. Still no change was told by someone that the ecm/cpu may need to be reset, did that also. Still no change. There are no codes present but still has the multiple misfires.
View 9 RepliesFord Super Duty (1999-2016) :: 2015 F250 - No Compression On 3 Cylinders
I've got a 2015 F250 with a 6.2 Liter with no compression on 3 cylinders. The dealer just diagnosed it and has not opened it up yet but the mechanic says it is probably a broken valve spring...that it is not uncommon in this engine.
My concern is not repairing the spring my concern is what a "free spinning" piston in 3 cylinders does to the life expectancy of the main and connecting bearings in this engine. I have rebuilt engines in the past and I have bought re-built from auto parts stores and from Jasper and I have never had any last more than 60-70K miles. It seems to me that even with very little mileage on the engine with three of eight pistons jumping around under no pressure that there could be considerable scarring of the bearings or bearing surfaces. I am no expert by any stretch but this is an engine in atruck that has less than 22K miles on it and I ain't real happy about opening it up let alone trusting for the next 280K miles that the bearings have more wear on them than they should have. It was only driven about 20 miles total like this but that is a lot of pressure on a highly tuned and pretty darn precision machine.
This is the newest vehicle I have owned since 1988 and I meant for it to be the last pickup I drive (I drive 'em til the wheels fall off) but I am not overly confident that even if this is a one off problem that it hasn't caused even more damage that won't show up for another 100K miles or so???
Ford Super Duty (1999-2016) :: 2000 F250 5.4 - No Compression On Cylinders
I have a 2000 ford f250 5.4 2v that's been having a shaking at idle and no power what so ever. I tried diagnosing it myself and came up with nothing. I finally decided to take it to the dealer and they are telling me that the right side has no compression on 3 cylinders. They want almost 7000 for a new engine. I was wondering if it was possible to get away with just putting a new head on the right side?
View 13 Replies