Ford Super Duty (1999-2016) :: 2008 - Hood Won't Stay Up - Lift Cylinders?
I got to replace mine because the hood won't stay up on it's own and is heavy to lift. I was wondering if these things fail often. Mine is an '08.
View 5 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Loud Whine Noise Comes From Under The Hood
I have a 2004 Ford F250 Turbo Diesel, egr delete, headstuds, intake, dual stacks, etc and when i turn my wheel a loud whining noise comes from under the hood, I noticed it put tension in my brakes. When I accelerate it gets louder and when i let off the gas it goes away... i checked my fluid in my steering pump and it was low so i put some more in and the next day it was all sitting under neath the truck.... any quick fix or do i need to replace the whole pump?
View 2 RepliesFord Super Duty (1999-2016) :: Loud Squealing Sound On Driver Side / Lift Pump?
Truck details:
2008 f350 6.4 290,000 klm
DPF and full EGR delete
K&N intake
IDP custom street tune
Loud squealing noise that happens when cold or at temp.
2000 to 2500 rpm's to 3000 rpm then it goes away
Happens only when accelerating over 50% anything under and the noise doesn't happen.
15 to 20 pounds of boost
Turbo sounds good
No codes
All plumbing looks sealed and tight
Fuel coolant res is full and clean
I'm thinking it could be the lift pump dying or having trouble supplying the fuel demand. Started after I did the cold air intake....
Ford Super Duty (1999-2016) :: F250 - 4R100 Unexpectedly Coasts - Accelerator Pedal Will Not Rev The Engine
I have a 99 F250 7.3PSD; I upgraded the tranny cooler after an episode of overheating while backing up a hill.
The truck has done well, hauled a few tractors with it, but recently I have noticed something that seems scary. When going downhill, I often relax on the accelerator. Usually there is some passive engine braking as happens with any auto tranny. Recently, the truck just coasts - it is as if you feel the tranny shift into neutral and you just coast, except I didn't shift. While this is happening, the accelerator pedal will not rev the engine. You can put the pedal all the way down -> rpms at about 6-800. No response.
At the bottom of the hill (so far) the engine gets louder. the rpms drop, and the accelerator works again. Every time, so far. But, if IO am going down hill, and want to accelerate to execute a laneg change or something - I can't. AFAIK, everything A-OK after the new tranny cooler. levels, etc.
Ford Super Duty (1999-2016) :: At 60 - 65 Over Bump Loud Rattle Noise?
I was driving and i was doing about 60 65 and i hit a bump and i heard a loud rattle and it shock the hell out of me then it just stop...
View 2 RepliesFord Super Duty (1999-2016) :: Loud Bang And Brake Pedal Went All The Way To The Floor
I was driving, Iput the brakes on then suddenly I heard a loud bang and brake pedal went all the way to the floor. I knew there was something wrong with the brakes, parked went and checked the passenger side rear brake caliper was ripped off which made a hole through my rim and also ripped off the brake lines. I need to get the part but I don't know what its called. See the pictures....
View 12 RepliesFord Super Duty (1999-2016) :: 2004 - Accelerator Won't Respond In Drive - Throttle Position Sensor?
Recently on two occasions I pressed the accelerator clear to the floor with no response. After shifting into Park then back into Drive it drove normally for about a week. Now it has stalled out and was very stubborn to restart. Once running, the accelerator will sluggishly rev the engine while in Park, but in Drive, will not respond. TPS sensor or something else?
2004 6.0 Diesel, 75K miles, no mods, well maintained.
Ford Super Duty (1999-2016) :: No Full Turn Right After Lift Kit
So last week I installed a 6" lift and once we got it done I could barley turn right at all. So I decided to put a drop pitman arm on yesterday with a buddy, thinking that was the issue. But I still have the problem, and I very badly need to fix it and don't know what it is. Turning left is completely fine however. It feels like I'm trying to steer an 18 wheeler right now.
View 6 RepliesFord Super Duty (1999-2016) :: Tires Upgrade With No Lift?
Looking to upgrade my tires and would like to go a hair bigger but nothing radical. I have the 20's now, what's the biggest size I can go to with no lift.
View 2 RepliesFord Super Duty (1999-2016) :: 2008 - Lift Kit Doesn't Sit Level
I have a fabtech 4 link 6" lift on a 2008 6.4. The lift kit used to sit level but the front is sitting lower now. How can I fix this?
View 10 RepliesFord Super Duty (1999-2016) :: Rear End Shudder / Vibration After Lift Installed
So I'm getting a mild to severe shudder depending on load and acceleration rate from stop to 10-15mph... It's worse if I'm on an incline...This has started since having a lift installed...I'm guessing it has everything to do with pinion angle...right?
1999' F350 7.3L 4x4
Crew Cab Long Bed
Ford Super Duty (1999-2016) :: Front Drive Shaft Angle After Lift
I finally got my lift installed the other day from PMF. My question is how do I get my pinion angle corrected on the front drive shaft? I know Trevor sells a Tcase clocking adapter may have to go that route IDK Unlike the rear there's only so much pitch you can put on the front axle until it causes issues with steering. I was thinking of going with an aftermarket front drive shaft designed to handle harsher angles.
I live in the mountains and after installing the lift and pulling a trailer on some of theses steeper gravel roads I can feel a harshness or something coming from under to front of the truck. I'm unable to post pics since I'm back on the road but I can visually see the front drive shaft angle is definitely not in line like it was.
I'm currently running PMF 2.5 alpha with a 1'' spacer and 3 link kit up front and 5'' progressive leafs and traction bars out back. I was able to fix my rear shaft angle using shims on my carrier bearing ( not really a big fan having 1 1/2'' of stacked shims BTW ) ....
Ford Super Duty (1999-2016) :: 2002 - Adding Suspension Lift Kits?
I have a 02 f250 powerstroke and I wanna put a suspension lift kit on it I wanna go with a 6 inch lift but I'm afraid if I go any higher than a 4 inch I'll have to change to much. What I would have to change and if I would have to extend any of my brake lines also the truck is a cab and a half with an 8 foot bed so I do have a carrier baring on the drive shaft would I have to change anything with that?
View 14 RepliesFord Super Duty (1999-2016) :: How To Lift Suspension To Change Out Spring Bushings
2003 f250 6" lift on 35s. How to lift the suspension to change out spring bushings? Was thinking using two chain falls on tow hooks on the front, any easier, safe, cheaper way. I have a farm jack but need to weld a plate on bottom of it for more support...
View 5 RepliesFord Super Duty (1999-2016) :: Lift / Leveling - Clunk Every Time When Turn To The Right
Put in 2.5" leveling blocks under front coil springs. Now I hear a clunk nearly every time I turn to the right. Why this might be?
View 3 RepliesFord Super Duty (1999-2016) :: Clunk After Lift Install At Low Speed Or When Stopped
Just installed a 4" lift sunday, with a BDS drop pitman arm and then i retorqued it to 185 ft/lb. I now have this extremely low speed (<2mph) or stopped clunking whenever i turn the wheel. I just replaced the upper and lower tie rod that goes from the pitman arm, and its still doing the same thing. Steering box is shot?
Clunk after lift install - YouTube .....
Ford Super Duty (1999-2016) :: Where To Put Jack Stands When Installing Front Lift Shackles
When installing front lift shackles, do you place jack stands under the axle, or the frame? I can't really find an answer. I assumed the axle, but i saw a thread and from what i could see it looked like it was supported at the frame and the axle was hanging free in the air. Just want to be sure before i start unbolting the stock shackles tomorrow and kill myself.
View 14 RepliesFord Super Duty (1999-2016) :: 2004 F250 - No Brake Pedal Sinking
I don't know whats up with my new truck, its a 04 f250 scsb, 4x4, 5.4l with 61k orig miles on it. Truck will stop on a dime, has NO pedal sinking, but it takes about 3/4 of the pedals travel to apply pressure to the pads and have the truck stop, sometimes if I push the pedal down then let up and push it again the pedal wont travel as far, I just flushed the system today, no air in the lines, is there a bleeder on the abs? truck has 4 wheel abs...
View 14 RepliesFord Super Duty (1999-2016) :: F250 - Raising Front - 3 Inch Lift Spindles Work Fine?
want to raise the front of my 99 f250 super duty. I only found rough country for my options. I am looking for a 2-3" lift. Will the 3" lift spindles work fine? What else am i going to need? Shocks?
[URL].....