Ford Super Duty (1999-2016) :: Replacing Shocks - Rough Ride?
It is about time to replace the shocks on my truck but I am going back and forth between shocks... I have 37s and the ride is rough to say the least I am looking for something to make it feel like I am not riding around on a jack hammer every time I hit a rock.
Dual set up in the front and single in the back and I have steering stabilizers installed.
Ford Super Duty (1999-2016) :: 2014 F250 - Shocks Are Leaking
I just picked up a 14 F-250 with 6.2 engine. the shocks are leaking, and before I order new ones I want get opinions. I was looking at Bilstein 5100 series. 24-186025 for the rear, and 24-186018 for the front. are these the best, or should i get something else.
View 3 RepliesFord Super Duty (1999-2016) :: Truck Won't Start After Changing Front Shocks
Last night was changing front driver's side shock on my 2011 F250 PSD. Right front wheel still on ground and needed to turn wheel to right to better access shock mount. Started truck and turned the wheel all the way to the right and took the key out thinking the wheel would lock and I could change the shock easier. But the wheel didn't lock and actually spun itself almost a full turn after I took the key out...I'm assuming because the right wheel was still on the ground providing resistance, but I think the wheel lock may have broken.
Finished the shock and went to start, but nothing. Everything is clicking and buzzing like normal but wouldn't turn over. Checked all fuses that seemed pertinent but none were bad. Wasn't able to check any relays. Gave up and was going to have it towed.
Son and I had to straighten the wheel so I could roll in down the driveway and the dang thing started after the wheel was straight! Thought it was a fluke and parked it. This morning did the same thing so I cranked the wheel to the right and it started again. Now at work and thought I better check again and I can't get it to start for anything. The steering wheel lock seems to be busted and now I'm thinking it could be something in the steering column, but this is a little above my pay grade.
Need to get home tonight and was hoping my description would be enough to make a for sure diagnosis. Otherwise its getting towed to the shop and I'd rather fix it myself if i can.
So went back out and tried starting in neutral again, but this time fiddled with the shifter while turning the key...nothing again. Ran it up into park and tried it again and it started! Last night and this morning I didn't mess at all with the shifter, just manually turned the wheel with the engine off. This is the first time moving the shifter worked and I didn't turn the wheel at all this last time.
Ford Super Duty (1999-2016) :: 2012 F250 - Replacing Shocks And Airbags?
I have a 2012 F250 King Ranch with the FX4 package. I have a goose neck ball and have recently bought a 37' fifth wheel. The rear of my truck sits a touch lower than the front and anytime I'm hooked to a trailer it looks to be squatted way down. It actually is dropping maybe 3". I am looking to replace the shocks which are Rancho's as I have 55k miles on. I'm wondering about shock types, air bags, springs??? Just don't know what my best option is.
View 9 RepliesFord Super Duty (1999-2016) :: Trailer Brake Controller Install
I've just bought a new 2016 SD xlt. The only extra I wanted that is missing is the factory trailer brake controller. The dealer told me it had to be programmed. I was expecting plug and play and planned to do it myself till they told me that. Is this true?
View 14 RepliesFord Super Duty (1999-2016) :: Upfitter Switches Relay Install
I want to install a set of upfitter switches but my truck didn't come with them...so I bought the switches and the relay/wire harness as well...I cannot find any good information on where to mount the relay and where an extra plug on that harness goes too. I have found the wires that attach and go through the firewall but I am not sure where the rest of this mess goes...my truck did not come with the wire harness already installed...
View 4 RepliesFord Super Duty (1999-2016) :: Install Pics For SCT Livewire 5015
My dad is looking to purchase a tuner from 5-Star for his 01 Super Duty. He's leaning towards splurging on the Livewire 5015. I know the unit comes with a suction cop, but I was curious if anyone has come up with something cleaner. I searched, but didn't find anything.
Any install pics or ideas?
Mike
Ford Super Duty (1999-2016) :: 2011 - Nav Install - Camera Redirecting?
I have recently upgraded the factory sync system in my 2011 f350 lariat to a factory sync with NAV. I am looking for tha way to redirect the fideo feed to the rear view mirror to the nav system, I have found the wire coors and pin locations for the radio end, just need the info if there is a way to move it in the a pillar harness on the passenger side to the radi harness.
Did ford really put 2 different harnesses in the cab if you had nav or not? Factory nav unit and factory camera (camera was in the vehicle to begin with). the radio side is pin 1 and 6 on the 10 pin radio harness.
Ford Super Duty (1999-2016) :: Plow Mount Brush Guard Install
So I've had this WAAG brush guard laying around for a few years and figured it was time to do something with it. Of course it was bought with no mounting brackets. I had found a lower gear from a Fisher MM1 plow. Tossed the in the truck and started from there.
Broke out the cherry picker and started lining stuff up. Drilled some holes and bolted it up. It's all bolted up but I still need to take a piece of 2x3 angle and weld it to the lower plow mounts to tie the bottoms together and create a step.
Ford Super Duty (1999-2016) :: Clunk After Lift Install At Low Speed Or When Stopped
Just installed a 4" lift sunday, with a BDS drop pitman arm and then i retorqued it to 185 ft/lb. I now have this extremely low speed (<2mph) or stopped clunking whenever i turn the wheel. I just replaced the upper and lower tie rod that goes from the pitman arm, and its still doing the same thing. Steering box is shot?
Clunk after lift install - YouTube .....
Ford Super Duty (1999-2016) :: 2012 F350 - Can Install Upgraded Message Center?
Found some threads on this but mostly for the 05-07 models. I am wondering if it is possible to install the upgraded message center (right above the steering column) into the dash of a 2012 F-350 XLT that has only the 2-line text message center?
View 1 RepliesFord Super Duty (1999-2016) :: 2005 - Driving Light Install In Front Bumper
I would like to install some driving lights behind the front bumper of my 2005 Super Duty, I was going to drill two 5" holes and than weld in some 5" pipe from the behind the bumper and attach some 5" KC driving lights to it. Would a hole saw work for this or is a bumper to thick? I was looking at DeWalt or Lenox hole saws their bi-metal. I know that I have to drill slow and I was going to use cutting fluid. I could use my drill press but I think I would have to figure how to clamp a bumper to the table. Then I am going to grind/sand the chrome off and paint it black. I will be taking the bumper off doing all of this.
View 4 RepliesFord Super Duty (1999-2016) :: 2013 F250 - Amber Flashing Light Install
I'm installing a new amber light on my 2013 F250 signal cab and was wondering where most people run the wires into the cab. It has a magnetic mount and I didn't want to put a hole in the roof. I have a cap on the truck and I also don't have a sliding rear window. This will not be a temp. install. Putting the wires in through a hole in the 3rd brake light?
View 3 RepliesFord Super Duty (1999-2016) :: Alarm With Remote Start Install - Wiring Diagram?
I am looking for a site that i can download a service manual with good wire diagrams. I want to install an alarm with remote start and need to know what wires go to what.
View 2 RepliesFord Super Duty (1999-2016) :: 2000 F350 - How To Correctly Install Front Drive Shaft
I want to install a new front drive shaft in my 2000 F350. I have the new one, and it has a big nut and it is threaded for length adjustment. My old one has a rubber boot which is missing from the new one. I plan on using red locktite but I do not know the torque specs on the front universal caps. Should I take it to my mechanic? I've never owned a 4x4 before.
View 3 RepliesFord Super Duty (1999-2016) :: Install And Mount A Light Bar Without Drilling Into The Front Bumper Or Grill?
Any good way to install and mount a light bar without drilling into the front bumper or grill? I have a 32" LED bar I want to mount between the top of the bumper and bottom of the grill, but the mounts aren't ideal for where I want to put the light.
View 9 RepliesFord Super Duty (1999-2016) :: 2006 F250 - Fog Light Switch / Driving Lights Install
I just ordered a set of Hella 4000x driving lights for my 2006 F-250. I have an aftermarket bumper on it, so the fog lights were taken out as there was no place to put them once the new bumper was installed. The question is, will I have any issues hooking the new driving lights up directly to the fog light system so I can just run them off the fog light switch instead of having to install the new switch on my dashboard? I know the new lights are 12V, but I couldn't find info as to whether the fog lights were running 12V as well.
View 2 RepliesFord Super Duty (1999-2016) :: 2012 F250 XLT - Power Sliding Rear Window Install
I am trying to change out my solid back glass for a power slider that's oem... My question that ford could not answer is, is the wiring all in place minus the switch for the install.. I have a 2012 F250 XLT. I am not even sure where the switch to move the window would go either...
View 2 RepliesFord Super Duty (1999-2016) :: 2010 F250 XL - OEM Fog Light Install / Switch Didn't Light Up
I have a 2010 f250 XL v10 6 speed 4wd. I was looking into adding factory fog lights to it. I have the factory plug by the headlight. I've read that some XL trucks just need the fog lights, wiring harness for the lights and the headlight switch with the fog light option.
So today my buddy (has an 09 f250 xlt with factory fog lights) and I decided to try his headlight switch in my truck to see if it would send power to the plug by the headlight. Plugged it in, turned the fog lights on and had no power. Actually the little fog light light on the switch didn't light up that I noticed either. So we compared wiring harnesses going to the headlight switch. Both trucks have 9 wires. #21 fuse in the kick panel is intact and good.
What else my truck would need in order to use the factory fog light parts? I know I could run new wiring and use an aftermarket switch but I'd rather it be factory.