Ford Super Duty (1999-2016) :: Clunk After Lift Install At Low Speed Or When Stopped
Just installed a 4" lift sunday, with a BDS drop pitman arm and then i retorqued it to 185 ft/lb. I now have this extremely low speed (<2mph) or stopped clunking whenever i turn the wheel. I just replaced the upper and lower tie rod that goes from the pitman arm, and its still doing the same thing. Steering box is shot?
Clunk after lift install - YouTube .....
Ford Super Duty (1999-2016) :: No Full Turn Right After Lift Kit
So last week I installed a 6" lift and once we got it done I could barley turn right at all. So I decided to put a drop pitman arm on yesterday with a buddy, thinking that was the issue. But I still have the problem, and I very badly need to fix it and don't know what it is. Turning left is completely fine however. It feels like I'm trying to steer an 18 wheeler right now.
View 6 RepliesFord Super Duty (1999-2016) :: After Leveling Kit Won't Go Forward?
I have a 99 v8 with a 8" lift. I just added a front leveling (mini spring pack) to replace the lifting block (death trap). Anyways after I installed the 2" spring pack and removed the 1.5" block the truck will not go into 4wd. Did I do something wrong? I did not unhook anything. I just unbolted the spring and shocks, lowered the axle down, then installed the new springs. By the way it has the warren aftermarket manual hubs (lock or free). I can hear the t-case engaging and the light says its in 4wd.
View 14 RepliesFord Super Duty (1999-2016) :: Left Turn Signal On All The Time
2012 F250 left turn signal on all the time no right turn signal.
View 2 RepliesFord Super Duty (1999-2016) :: Tires Rubbing After Installing Leveling Kit
I had my leveling kit installed today. Bilstein 2" leveling coils, adjustable track bar, 4" rear blocks, and shocks front and rear.
I have 295/70/18 tires on stock wheels that didn't rub anywhere before. Now at full lock to the left the drivers side tire just barely rubs on the radius arm. How is that possible? I was planning on getting 35s soon when these wear out but it seems like those would rub even worse.
Ford Super Duty (1999-2016) :: Leveling Kit - Spacers Or Track Bar Relocation?
2015 F350, Want to do a leveling kit. Are the spacers good enough or should I do the track bar relocation too?
View 5 RepliesFord Super Duty (1999-2016) :: 2007 F250 - Front Wheel Clunk When Turn Sharply In Either Direction
2007 F250 4WD 5.4l ... when I turn sharply in either direction I am getting a light clunk sound similar to when you are in 4WD on blacktop and try turning. The engine also seems to wanna stall when I cut the wheel too sharp.
View 4 RepliesFord Super Duty (1999-2016) :: 2002 F250 2wd Leveling Kit - Front End Sagging So Low?
I recently purchased a 2002 F250 Regular cab long bed 2wd. I'm tired of the front end sagging so low, so I've been looking into a leveling kit. I was wondering whether I should go with 2" or 1.5" for the kit. I tow about 2000 lbs. 3-4 days a week and do not want the truck to look like it is squatting too badly. However, I really would like it too look more level.
View 8 RepliesFord Super Duty (1999-2016) :: Steering Wheel Makes A Popping Noise Every Time Turn It
My steering wheel makes a popping noise at the same location every time I turn it, ie the 7:00 position. The popping is within the steering column inside the truck and sounds like its right behind the airbag. Its simply a popping noise and slight movement in the steering every time I turn the steering wheel from 12 to 7. I have no clue what it is and cant figure it out. My truck is a 2008 F250 2WD 5.4
This is a video of another person who appears to have the same exact problem, hopefully this will add some clarity to what I was trying to describe above. If you notice, when he turns it to the right, his steering wheel pops in the exact same location every time as well which is what mine is doing when I turn it to the left.
2010 f150 steering wheel pop - YouTube ....
Ford Super Duty (1999-2016) :: Tires Upgrade With No Lift?
Looking to upgrade my tires and would like to go a hair bigger but nothing radical. I have the 20's now, what's the biggest size I can go to with no lift.
View 2 RepliesFord Super Duty (1999-2016) :: 2008 - Lift Kit Doesn't Sit Level
I have a fabtech 4 link 6" lift on a 2008 6.4. The lift kit used to sit level but the front is sitting lower now. How can I fix this?
View 10 RepliesFord Super Duty (1999-2016) :: Rear End Shudder / Vibration After Lift Installed
So I'm getting a mild to severe shudder depending on load and acceleration rate from stop to 10-15mph... It's worse if I'm on an incline...This has started since having a lift installed...I'm guessing it has everything to do with pinion angle...right?
1999' F350 7.3L 4x4
Crew Cab Long Bed
Ford Super Duty (1999-2016) :: Front Drive Shaft Angle After Lift
I finally got my lift installed the other day from PMF. My question is how do I get my pinion angle corrected on the front drive shaft? I know Trevor sells a Tcase clocking adapter may have to go that route IDK Unlike the rear there's only so much pitch you can put on the front axle until it causes issues with steering. I was thinking of going with an aftermarket front drive shaft designed to handle harsher angles.
I live in the mountains and after installing the lift and pulling a trailer on some of theses steeper gravel roads I can feel a harshness or something coming from under to front of the truck. I'm unable to post pics since I'm back on the road but I can visually see the front drive shaft angle is definitely not in line like it was.
I'm currently running PMF 2.5 alpha with a 1'' spacer and 3 link kit up front and 5'' progressive leafs and traction bars out back. I was able to fix my rear shaft angle using shims on my carrier bearing ( not really a big fan having 1 1/2'' of stacked shims BTW ) ....
Ford Super Duty (1999-2016) :: 2002 - Adding Suspension Lift Kits?
I have a 02 f250 powerstroke and I wanna put a suspension lift kit on it I wanna go with a 6 inch lift but I'm afraid if I go any higher than a 4 inch I'll have to change to much. What I would have to change and if I would have to extend any of my brake lines also the truck is a cab and a half with an 8 foot bed so I do have a carrier baring on the drive shaft would I have to change anything with that?
View 14 RepliesFord Super Duty (1999-2016) :: How To Lift Suspension To Change Out Spring Bushings
2003 f250 6" lift on 35s. How to lift the suspension to change out spring bushings? Was thinking using two chain falls on tow hooks on the front, any easier, safe, cheaper way. I have a farm jack but need to weld a plate on bottom of it for more support...
View 5 RepliesFord Super Duty (1999-2016) :: 2008 - Hood Won't Stay Up - Lift Cylinders?
I got to replace mine because the hood won't stay up on it's own and is heavy to lift. I was wondering if these things fail often. Mine is an '08.
View 5 RepliesFord Super Duty (1999-2016) :: Where To Put Jack Stands When Installing Front Lift Shackles
When installing front lift shackles, do you place jack stands under the axle, or the frame? I can't really find an answer. I assumed the axle, but i saw a thread and from what i could see it looked like it was supported at the frame and the axle was hanging free in the air. Just want to be sure before i start unbolting the stock shackles tomorrow and kill myself.
View 14 RepliesFord Super Duty (1999-2016) :: Loud Squealing Sound On Driver Side / Lift Pump?
Truck details:
2008 f350 6.4 290,000 klm
DPF and full EGR delete
K&N intake
IDP custom street tune
Loud squealing noise that happens when cold or at temp.
2000 to 2500 rpm's to 3000 rpm then it goes away
Happens only when accelerating over 50% anything under and the noise doesn't happen.
15 to 20 pounds of boost
Turbo sounds good
No codes
All plumbing looks sealed and tight
Fuel coolant res is full and clean
I'm thinking it could be the lift pump dying or having trouble supplying the fuel demand. Started after I did the cold air intake....
Ford Super Duty (1999-2016) :: 2004 - Loud Rattle Under The Hood When Lift Off The Accelerator Pedal
I bought a 2004 F250 super duty 4x4 with the 6.0 a couple weeks ago and have a few questions. Hopefully all of these things are normal, but I thought I would ask you experienced drivers.
1) Occasionally while driving when I lift off the accelerator pedal I can hear a sort of loud rattle under the hood. I assume this is the turbo shutting down? Is that normal?
2) 4x4 and locking hubs... I have the 4x4 hi and low switch on the dash. Do I need to also manually lock the hubs to go into 4x4? After reading the manual it seems like I can just turn the dash switch and they should automatically lock, but I'm not sure. The hubs are not marked, but going by the pictures in the manual I think I know which is "lock" and which position is "auto" or off.
3) Front wheels hop at full turn. I expected wheel hop in 4x4 or with the hubs locked, but even in 2WD with the hubs in the auto position the tires still "hop" or knock a bit at sharp turns. Is this normal?