Ford Super Duty (1999-2016) :: 2004 F350 - Bolt Hole Diameter On Front Shackles
I am getting ready to make a set of front shackles for my truck for a temporary lift solution to fit my 35s until i can afford a complete suspension lift kit. I cannot for the life of me find the size of the hole for the bolts. I don't wanna drill it too big then have play in the shackle. My stockers are still installed so I don't have those to measure just yet. Need to verify the diameter hole i need to drill? and stock shackles look to be about 5.25" center to center, from what i can measure with them installed on the truck? so 2" lift, the new shackles will need to be about 9.25" center to center, right? (add 4", nets a 2" lift?)
View 7 RepliesFord Super Duty (1999-2016) :: Front Drive Shaft Angle After Lift
I finally got my lift installed the other day from PMF. My question is how do I get my pinion angle corrected on the front drive shaft? I know Trevor sells a Tcase clocking adapter may have to go that route IDK Unlike the rear there's only so much pitch you can put on the front axle until it causes issues with steering. I was thinking of going with an aftermarket front drive shaft designed to handle harsher angles.
I live in the mountains and after installing the lift and pulling a trailer on some of theses steeper gravel roads I can feel a harshness or something coming from under to front of the truck. I'm unable to post pics since I'm back on the road but I can visually see the front drive shaft angle is definitely not in line like it was.
I'm currently running PMF 2.5 alpha with a 1'' spacer and 3 link kit up front and 5'' progressive leafs and traction bars out back. I was able to fix my rear shaft angle using shims on my carrier bearing ( not really a big fan having 1 1/2'' of stacked shims BTW ) ....
Ford Super Duty (1999-2016) :: F250 - Raising Front - 3 Inch Lift Spindles Work Fine?
want to raise the front of my 99 f250 super duty. I only found rough country for my options. I am looking for a 2-3" lift. Will the 3" lift spindles work fine? What else am i going to need? Shocks?
[URL].....
Ford Super Duty (1999-2016) :: F250 - Using Jack Stand On Rear Axle
Just got done rotating my tires on my 16 F250 ccsb 4x4 and I used jack stands on my rear axle while I used the jack on the front axle. When I brought the truck down off the jack stands (first time using jack stands on this truck) I saw that they left little marks/divits on the rear axle. I had them between the wheel and the shock support and I can feel with my finger where the jack stand was supporting the truck. It doesn't seem anything major but I can surely point out to you exactly where the axle and the jack stand met. I'm sure this is a non issue but just wanted to check in here to make sure...
No trailer attached (of course!) And nothing in the bed with a full tank of gas...so basically just the weight of the truck...
Ford Super Duty (1999-2016) :: No Full Turn Right After Lift Kit
So last week I installed a 6" lift and once we got it done I could barley turn right at all. So I decided to put a drop pitman arm on yesterday with a buddy, thinking that was the issue. But I still have the problem, and I very badly need to fix it and don't know what it is. Turning left is completely fine however. It feels like I'm trying to steer an 18 wheeler right now.
View 6 RepliesFord Super Duty (1999-2016) :: Tires Upgrade With No Lift?
Looking to upgrade my tires and would like to go a hair bigger but nothing radical. I have the 20's now, what's the biggest size I can go to with no lift.
View 2 RepliesFord Super Duty (1999-2016) :: 2008 - Lift Kit Doesn't Sit Level
I have a fabtech 4 link 6" lift on a 2008 6.4. The lift kit used to sit level but the front is sitting lower now. How can I fix this?
View 10 RepliesFord Super Duty (1999-2016) :: Rear End Shudder / Vibration After Lift Installed
So I'm getting a mild to severe shudder depending on load and acceleration rate from stop to 10-15mph... It's worse if I'm on an incline...This has started since having a lift installed...I'm guessing it has everything to do with pinion angle...right?
1999' F350 7.3L 4x4
Crew Cab Long Bed
Ford Super Duty (1999-2016) :: 2002 - Adding Suspension Lift Kits?
I have a 02 f250 powerstroke and I wanna put a suspension lift kit on it I wanna go with a 6 inch lift but I'm afraid if I go any higher than a 4 inch I'll have to change to much. What I would have to change and if I would have to extend any of my brake lines also the truck is a cab and a half with an 8 foot bed so I do have a carrier baring on the drive shaft would I have to change anything with that?
View 14 RepliesFord Super Duty (1999-2016) :: How To Lift Suspension To Change Out Spring Bushings
2003 f250 6" lift on 35s. How to lift the suspension to change out spring bushings? Was thinking using two chain falls on tow hooks on the front, any easier, safe, cheaper way. I have a farm jack but need to weld a plate on bottom of it for more support...
View 5 RepliesFord Super Duty (1999-2016) :: Lift / Leveling - Clunk Every Time When Turn To The Right
Put in 2.5" leveling blocks under front coil springs. Now I hear a clunk nearly every time I turn to the right. Why this might be?
View 3 RepliesFord Super Duty (1999-2016) :: 2008 - Hood Won't Stay Up - Lift Cylinders?
I got to replace mine because the hood won't stay up on it's own and is heavy to lift. I was wondering if these things fail often. Mine is an '08.
View 5 RepliesFord Super Duty (1999-2016) :: Clunk After Lift Install At Low Speed Or When Stopped
Just installed a 4" lift sunday, with a BDS drop pitman arm and then i retorqued it to 185 ft/lb. I now have this extremely low speed (<2mph) or stopped clunking whenever i turn the wheel. I just replaced the upper and lower tie rod that goes from the pitman arm, and its still doing the same thing. Steering box is shot?
Clunk after lift install - YouTube .....
Ford Super Duty (1999-2016) :: Loud Squealing Sound On Driver Side / Lift Pump?
Truck details:
2008 f350 6.4 290,000 klm
DPF and full EGR delete
K&N intake
IDP custom street tune
Loud squealing noise that happens when cold or at temp.
2000 to 2500 rpm's to 3000 rpm then it goes away
Happens only when accelerating over 50% anything under and the noise doesn't happen.
15 to 20 pounds of boost
Turbo sounds good
No codes
All plumbing looks sealed and tight
Fuel coolant res is full and clean
I'm thinking it could be the lift pump dying or having trouble supplying the fuel demand. Started after I did the cold air intake....
Ford Super Duty (1999-2016) :: 2004 - Loud Rattle Under The Hood When Lift Off The Accelerator Pedal
I bought a 2004 F250 super duty 4x4 with the 6.0 a couple weeks ago and have a few questions. Hopefully all of these things are normal, but I thought I would ask you experienced drivers.
1) Occasionally while driving when I lift off the accelerator pedal I can hear a sort of loud rattle under the hood. I assume this is the turbo shutting down? Is that normal?
2) 4x4 and locking hubs... I have the 4x4 hi and low switch on the dash. Do I need to also manually lock the hubs to go into 4x4? After reading the manual it seems like I can just turn the dash switch and they should automatically lock, but I'm not sure. The hubs are not marked, but going by the pictures in the manual I think I know which is "lock" and which position is "auto" or off.
3) Front wheels hop at full turn. I expected wheel hop in 4x4 or with the hubs locked, but even in 2WD with the hubs in the auto position the tires still "hop" or knock a bit at sharp turns. Is this normal?
Ford Super Duty (1999-2016) :: Installing 12v Cummins?
I have a 1999 f-250 sd 4x4 that had a 5.4L auto trans and a switch operated transfer case. Im installing a 1998 12v Cummins, nv4500 5 speed, and dodge manual shift transfer case. My father and I have made engine mounts, modified trans cross member, and installed a 1/2 " dip tube into fuel tank an used 1/2" fuel line to connect to factory Cummins fuel line. We are now to the worst part now "WIRING". I still have the OEM gasser 5.4 wiring harness. I bought bushings to install ford coolant temp probe and ford oil pressured sensor. I got my harmonic balancer machined with 2 more notches for ford cam/crank sensor pickups but I'm just confused after reading a few different postings about tach. I guess just need a run down on the 12v wiring to the 5.4 pcm. I would like all factory dash gauges to work right, cruise control, and A/C to work. My 12v still has dodge alt and dodge a/c compressor. I ve bought a bunch of parts so after you post to this ill let you know if I have it or not. Things like ford clutch and brake pedal sets, ford OEM manual transfer case shifter setup, bushings for ford sensors to Cummins, and other things I've forgot about.
View 6 RepliesFord Super Duty (1999-2016) :: Installing Puddle Lights?
I am going to be installing puddle lights to light up my step bars and I am looking to find out which wire to tie into? I was going to tie into the dome light circuit (blk/blue) so they would come on with keyless entry door unlock, but my dome light won't come on. So I either have to figure that out or go to plan B and find a difference source. Adding lights down there and found another way to power these? I don't know if extended cabs ever had the option for lighted running boards, maybe there is a dedicated wire somewhere? I don't want them on all the time, only when the truck is unlocked to light the step.
View 12 RepliesFord Super Duty (1999-2016) :: 2000 - Installing Second Alternator?
The V10 in my service truck took the long slow ride. I located and am in the middle of replacing said engine. My question is, how difficult would it be to install a second alternator in this truck, considering I have it torn down for replacement?
It a 2000 F350 with a V10. I'm looking for more power as I have mounted on the Knaphiede service body a IMT 1015 crane, 3200 lb capacity. I would like to install a power inverter to be able to run an air compressor in the field.
Am I looking for a new harness? Etc?
Ford Super Duty (1999-2016) :: Tires Rubbing After Installing Leveling Kit
I had my leveling kit installed today. Bilstein 2" leveling coils, adjustable track bar, 4" rear blocks, and shocks front and rear.
I have 295/70/18 tires on stock wheels that didn't rub anywhere before. Now at full lock to the left the drivers side tire just barely rubs on the radius arm. How is that possible? I was planning on getting 35s soon when these wear out but it seems like those would rub even worse.