Ford F-150 - 1997-2003 :: 1999 - Check Engine Light Came On / Code P0171 / System Too Lean Bank 1

I just bought a 99 f150 and the check engine light came on with code p0171,system too lean bank 1. It runs and drives fine but has a strong smell of gas when I shut it off.

View 4 Replies

Ford - Explorer :: Codes P0171 And P0174 - Lean Bank 1 And 2 Sensor 2

I have been getting a P0171 and a P0174 code lean bank 1 and 2 sensor 2. I have replaced all 4 censers the 171 is gone but I keep getting the P0174 and it only comes on when I am on the highway after driving around 10 miles or so i got a freeze frame of the data when it happen.

View 6 Replies

Ford F-150 - 1997-2003 :: Engine Service Light - Codes P0171 And P0174

2001 F150 5.4L Triton Motor. Everything seemed o.k. then got the Engine Service Light. Checked with reader and above codes only appeared. Read numerous articles/videos and pulled the PCV hose/boot assembly and replaced the whole thing with oem part. Visually checked for disconnected tubing = none found. After this and with the new hose assembly in place I performed a reset. With the scanner still connected restarted engine and read values: ST FTRM1&2 = -.08~+2.3, both oxygen sensor voltages are varying and the LT FTRM1&2 hang around +26 and +28.

From what I understand the ST seems o.k. but the long term is WAY OUT OF WHACK. Started it up again and took carb cleaner spray and covered all the connections I could see = no change in engine rpm. No cracks in the air cleaner body. Big plug to the MAF was inserted and plugging the hole. I am thinking of making a smoke "machine" and trying that or removing the hoses from the throttle body and plugging the holes in the throttle body and see if that clears them up. IF it does then connect one by one and keep checking the values. Lot more work but I am at a loss.

View 6 Replies

Ford - Explorer :: 2003 - Lean Codes P0171 And P0174

2003 Sport Trac. My car was not starting, told my fuel pump, replaced twice and nothing. Found out about inertia switch and changed it, now car runs.

Before this switch blew out my car was running perfectly, no check engine, nothing. Now i have changed my fuel pump twice and put a brand new fuel filter in and soon after i get lean codes P0171 and P0174. My fuel pressure is 60psi at idle and drops to 0 after about 30 seconds when the car is shut off.

A lot of my intake is new since i did have a vacuum leak before, so i do not suspect that is it, especially since this happened after the new fuel pump. I am completely stuck as to what i should do. And i get hesitation when trying to accelerate sometimes

View 3 Replies

Ford Super Duty (1999-2016) :: Running Rough - Check Engine Light Came On And Got Codes P0171 And P0174

My 1999 F350 SD V10 that would crank but not start. I ended up checking numerous things because before it decided to truly stop running, it would run rough for a time and then be fine. The check Engine Light came on and I got the codes P0171 & P0174. Well, I bought MAF Cleaner and took the air cleaner housing off, disassembled it and thoroughly cleaned the sensor and replaced the air cleaner. I continued to get those same error codes, but before I could go any further, the truck totally died. It sat for nearly 2 months with the bed in the air as I had decided to lift the bed to check the fuel pump vs. drop the tank.

Fast forward a bit and I have since replaced the fuel pump and put $40 of Premium Gas along with Royal Purple Fuel Treatment in the tank because I figured things got stirred up and could use a bit of cleaning. I do not drive much, and during the first few trips, it ran perfectly. Then today, it started again with the rough running and trying to die if I let it idle. If I pushed on the gas, it would completely smooth out. If this were a carbureted engine, I would think the low idle was set too low, but since it is not, I am guessing it is one or more of the sensor/s that is/are causing the issue.

I am disabled and can’t play parts swap until I hit on the right part, so I was hoping that I might get some guidance here to narrow things down to the most probably causes so that I won’t go broke changing things until I hit the “right one”. The truck has 153,000 miles on it and I had bought it from a retired couple who used it to pull their 5th wheel travel trailer, so it had mostly highway miles on it. It was immaculate when I bought it and ran perfectly, needing only normal maintenance (oil changes, etc.) over the past 12 years that I have owned it. In those 12 years, I have put about 60,000 miles on it.

View 3 Replies

Golf V R32 :: CEL With Code P0171 And P0174 - Lean Bank 1 And 2

I am having a difficult time trying to fix my CEL issue, The vagcom scan says P0171 & P0174 Lean banks 1 and 2. I don't believe both O2's went out I have Checked and cleaned the MAF Sensor did a quick vacuum leak inspection and all seems good. I have a GIAC ST 1 and an AFE intake with noise pipe delete. I can reset it but it returns after a day or so.

View 1 Replies

Lexus - RX300 :: 2000 - Check Engine Light Code P0171 Bank 1 Too Lean

2000... I have a code P0171 bank 1 too lean. My question is does this exclude anything that will effect both banks? If it was MAF sensor or fuel filter would it set code and say banks 1 and 2 running too lean? In which MAF sensor ohms out correctly. I cannot view fuel trim files. I have looked for a vacuum leak with no luck. I got some cigars to try to smoke it to see if there is any vacuum leaks. Trying to narrowing what i need to checks.

View 19 Replies

Chevrolet - Trailblazer :: 2006 - Check Engine Light Code P0171 - Lean Bank 1

I have a 2006 Chevy Trailblazer LS/LT 4.2 liter 2wd. I have been trying to get it smoged, but can't clear the code. P0171 - Lean Bank 1.

I've been having a parts throwing contest with it, but it has been winning and my wallet is losing.

I have changed the air filter, cleaned the MAF sensor, changed both O2 sensors, changed the secondary air valve and relay. I've done the carb cleaner spray test around the intake and vacuum lines, with no spikes in RPM.

Most recent try was a couple bottles of Techron concentrate with premium chevron gas.(still waiting to see if the code hits again)

Next steps are checking the intake bolts(to see if they are torqued) and intake gaskets, check for exhaust leaks at the exhaust manifold, and checking the MAP sensor.

Freeze frame data from the most recent hit on the code is below.

***Fuel system 1 - CL***Fuel system 2 - NA***Calc Load(%) - 30.2***ECT(deg c) - 48***STFT B1(%) - 3.9***LTFT B1(%) - 22.7***MAP(kPa) - 33***Eng RPM - 809***Veh speed(km/h) - 0***Spark Adv (deg) - 10.5***IAT(deg c) - 20***MAF (G/s) - 5.82***TPS(%) - 15.3***Air status - NA.

View 7 Replies

Passat (B5) :: Check Engine Light Came On - Code P0171 / Fuel System For Bank 1 Was Too Lean

We have a 2003 Passat 1.8t. Had the Check engine Light come on. Went down to AutoZone and hookeded up the OBDII reader. Came up with P0171, Fuel System for Bank 1 was too lean. Probable causes:

1. Fuel Pressure of MAF (If Bank 1 & Bank 2 set codes together)
2. O2 Sensor
3. Ignition Misfire
4. Fuel Injector Problem

Car has 60K - has always run well. Wife says she thinks it's running a bit sluggish. I rarely drive the car, but I think she's right. Car is not missing or running rough.

I cleared the code & started the engine; Check Engine Light is off; then looked at the codes and I find a P0171 (Pending). She tells me that the light has been on before & then gone away. So I guess it clears itself, but eventually comes back.

View 10 Replies

Ford Excursion :: Check Engine Light Illuminated For Codes P0171 And P0174

Coming home from spring break towing the TT, the Check Engine light illuminates. Seems to be sputtering at idle, but otherwise OK, so we continued home.

Scanner lists the P0171 and P0174 codes. Ok, where to begin? based on internet info, started by cleaning the MAF sensor and throttle body. When I pulled apart the intake, noticed that the grommet which feeds the MAF in the air intake had become separated letting air bypass the MAF. Hence the reason for the codes.

If you get these codes, check the grommet for the wires feeding the MAF in the air intake to make sure it hasn't become separated from the intake. No more codes.

View 6 Replies

Ford F-150 - 1997-2003 :: 2002 - SES Light Came On - Showing Codes P0171 / P0174

2002 F150 - 5.4 ... So just bought this truck about a month an a half ago. No problems but the other day the SES came on. It is showing P0171 and P0174. And P0000 (almost forgot that one) was told that's generic though. Haven't really noticed a difference in the way it's running. Has been extremely cold here in WV but the only thing I can notice (or think I notice) is the gas mileage has gone down a little. After reading some on this forum I'm looking for a vacuum leak correct?

View 10 Replies

Ford F-150 - 1997-2003 :: Bank 1 Or Bank 2 Too Lean Codes At Idle When Started Cold?

I've been having this problem since I've gotten the truck about year ago. it has very high long-term fuel trims and it seems no matter what I do I cannot get them to go down my fuel trims at idle are 39 Bank1 and 33 bank2 they go down to around 12>7 while driving what could this mean. And even weirder occasionally I get Bank 1 or bank 2 too lean codes at idle when cold starting???? 1997 Ford F150 4.6 ......

View 7 Replies

Ford - Explorer :: 2001 - Too Lean Codes P0171 And P0174

Working on my son's 2001 sport trac. 200K miles but it has always been a great running truck.

I have two CEL codes:

P0171 System too Lean (Bank 1)
P0174 System too Lean (Bank 2)

I have found several issues so far, but have yet to get rid of these pesky codes.

So far I have changed:

- Intake Gasket - I had coolant loss which replacing this gasket fixed.
- PCV Valve and Hose - valve was damaged and the hose leaked.
- EGR Valve - Valve was leaking
- Fuel Filter
- Mass Airflow Sensor

The engine does appear to be running much smoother now, but the lean codes remain.

View 7 Replies

Santa Fe (CM - 2007-12) :: Check Engine Light Going On - Fuel System Lean Codes P0171 And P2187

My wifes 2007 Santa Fe Limited 3.3 has had a check engine light going on a year now. Car has about 122k on it now. Scanned codes about 6 months ago and had a fuel system lean code. Did some reading and ended up replacing the purge valve. The CEL stayed off til the end of the drive cycle and came right back. I have noticed when you fill the car up there is a real strong smell of gas but the car always starts right up. It now has a P0171 Fuel system too lean (b1) and P2187 Fuel system too lean at idle. Where to start. Don't have much background with hyundai. Also the ESC off light comes on randomly and goes off. Doesn't happen real frequently though.

View 4 Replies

Ford F-150 - 1997-2003 :: Codes P0304 And P0316 - Lean Bank 1 And 2

2003 F150 v6 2wd 170k ... For a year I've only had codes P0171 and P0174 (lean bank 1 and 2). I was told it wouldn't hurt anything... I think now I should have taken care of it.

Anyway 3 weeks ago my truck started running a little rough. It was sputtering and had trouble getting up to speed, sometimes also the air switches from vent to defrost until switch gears and rpms go down. It gradually got a lot worse over 10 days while part was otw. A week ago i changed MAF and cleaned the black thing it's inside of. It started running better but still not good. I pulled my small trailer 2 days ago and it got worse after dropping the trailer.

Today checked codes at AZ and lean codes are gone and have p0304 (#4 misfire) and p0316 (crank sensor problem). Is this related.? Also Right before all the trouble I changed battery and alternator. Also i read online that MAF needed 2 weeks to relearn the way I drive to get correct gas/air ratio? Is that correct?

Also I read so many different things I needed to do during installation... Some say I need to turn key to the on position after unplugging old MAF then plug new one in... turn key to on position 10 times, Rev up engine, drive it rough for the first 2 minutes... etc. Is there a correct way to do it or is it vehicle specific?

Should I start by changing spark plugs and coils? The guy i bought it from and trust said he changed spark plugs right before I bought it. Will it ruin truck if I drive it? I've read so much but everyone says so much different things on the same topic. I'd what to start with or if this is related.

View 14 Replies

Ford Excursion :: SES Light Came On About 15 Minutes Into Drive / Code P0174 - Bank 2 Lean

After installing Banks headers and full exhaust, I took my truck for another test drive this morning. SES light came on about 15 mins into drive and is telling me P0174 - Bank 2 Lean.

So that's the right/drivers side - my list of things to go check

O2 Sensor plug on that side
The MAF
The IAC
Vacuum lines ...

View 8 Replies

Ford F-150 - 1997-2003 :: Codes For Large EVAP Leak / Cylinder 6 Misfire / Bank 2 Lean

Here are the codes I'm getting:

P0455 - large evap leak
P1451 - main control (evap canister)
P0306 - cylinder 6 misfire
P0174 - bank 2 lean

are these all related? Or two separate issues. I have replaced all the evap lines with new lines. I have a new egr valve, and exhaust manifolds, and what should I look at 1st

View 4 Replies

Ford Super Duty (1999-2016) :: 2003 F250 SD 4x4 - DTC Codes P0171 / P0174 - Loose Fitting Oily Hose?

I've had DTC P0171 & P0174 (lean in bank 1 and lean in bank 2) for a few weeks now (check engine light cued me on it). Autozone scanned it for me. It's on a 2003 F250 SD 4x4 5.4L.

My first step was to clean the MAFS. Light came back on in about 30-40 miles. I then replaced the MAFS. 30-40 miles and the light came back on.

My first thought was disconnecting the battery wasn't resetting the comp and thats why the light was comming back on.

I went and picked up an Actron cheapy OBD II Scanner today at lunch. Cleared the codes with the scanner and drove back to work.

Checked the codes when I got back (no light on but was curious) and it shows P0171 & P0174 pending.

I've checked and the dipstick is seated properly. The hoses on the air intake appear to seated properly as well. The top hose is a pretty loose fit but it was seated all the way down. The top hose was oily. Not sure if this is normal or not. Could the loose fitting oily hose be the culprit?

Also, what is the lower hose? It comes off the back of the air intake and goes to the driver side valve cover. I know it's not the PCV hose as that is on the passenger side valve cover....right?

View 14 Replies

Ford F-150 (2004-2008) :: Missing On And Off - Check Engine Light - Bank 1 / 2 Too Lean

I bought 04 Lariat (5.4 3v around 100k miles, Roush Off Road side exit exhaust, DWV intake mod, SCT 3015 tuner).

The truck has had a miss on and off for around a month I've changed plugs and tested all the coils. Which cured the problem for around a week, the FPDM had some white stuff on back and soft spot but not ate through. The only Check Engine Lights have been bank 1 to lean (which went away as soon as it came. But yesterday and today I've got bank 2 to lean.

Below is a quick data log pull... The misses is about ready to ship her out if she don't straighten up..

View 2 Replies