Ford - Explorer :: 2001 - Too Lean Codes P0171 And P0174
Working on my son's 2001 sport trac. 200K miles but it has always been a great running truck.
I have two CEL codes:
P0171 System too Lean (Bank 1)
P0174 System too Lean (Bank 2)
I have found several issues so far, but have yet to get rid of these pesky codes.
So far I have changed:
- Intake Gasket - I had coolant loss which replacing this gasket fixed.
- PCV Valve and Hose - valve was damaged and the hose leaked.
- EGR Valve - Valve was leaking
- Fuel Filter
- Mass Airflow Sensor
The engine does appear to be running much smoother now, but the lean codes remain.
Ford - Explorer :: Codes P0171 And P0174 - Lean Bank 1 And 2 Sensor 2
I have been getting a P0171 and a P0174 code lean bank 1 and 2 sensor 2. I have replaced all 4 censers the 171 is gone but I keep getting the P0174 and it only comes on when I am on the highway after driving around 10 miles or so i got a freeze frame of the data when it happen.
View 6 RepliesFord F-150 - 1997-2003 :: 1999 - Check Engine Light Codes P0171 And P0174 Lean On Bank 1 / 2
I have a 99 f150 with the 4.2l v6 with a 5 speed 173000 miles. I picked it up not to long ago. When I first got it it had both the P0171 & P0174 lean on bank 1&2 it was also siting for a while. I replaced the fuel filter which was filled with black fuel, also changed the PCV valve, cleaned the MAF sensor, and changed the oil. I cleared the code, drove it for a little bit and the light came back on after 20 miles.
I then proceeded to replace the upper and lower intake manifold gaskets. Upon doing that i noticed that i was missing one of the linkages for the IMRC. I went to the junkyard and pulled off another linkage rod off the same motor. ordered new plastic clips, put the IMRC on cleaned everything up and began putting it back together. I also cleaned the Injectors while i had them out as well and put in new spark plugs and wires.
Put everything back together. code was cleared since the battery was disconnected. drove it and then the engine light came back on again. this time it was only the p0174. so i then both the upstream and downstream O2 sensors on bank 2, reset the code and it came back on again. I'm lost.
Ford - Explorer :: 2003 - P0171 And P0174 Codes - Rubber Elbow Begin To Collapse
2003 Ford Explorer, with P0171 and P0174 codes, common problem, as I have read. I pulled the cover over the engine off, and I immediately found the likely problem. There is a hose/connection that runs from the valve cover on the right side, about 6 inches behind the oil fill tube across and looks like it comes into the Carb. Where it turns to come into the carb is a rubber elbow. This elbow has a hole in it. Temporarily I have used electrical tape, but when I run the vehicle, I see the elbow begin to collapse. I believe the elbow is getting weak with age, plus the hole/tear doesn't work. Anyway, what i the part number, or what this is called. Hoping Advance Auto, or Napa will have it, just don't know what it is called, and can't figure out the part number. Otherwise I will pull it off tomorrow and take to advance and see if they can match it.
View 5 RepliesFord F-150 - 1997-2003 :: Engine Service Light - Codes P0171 And P0174
2001 F150 5.4L Triton Motor. Everything seemed o.k. then got the Engine Service Light. Checked with reader and above codes only appeared. Read numerous articles/videos and pulled the PCV hose/boot assembly and replaced the whole thing with oem part. Visually checked for disconnected tubing = none found. After this and with the new hose assembly in place I performed a reset. With the scanner still connected restarted engine and read values: ST FTRM1&2 = -.08~+2.3, both oxygen sensor voltages are varying and the LT FTRM1&2 hang around +26 and +28.
From what I understand the ST seems o.k. but the long term is WAY OUT OF WHACK. Started it up again and took carb cleaner spray and covered all the connections I could see = no change in engine rpm. No cracks in the air cleaner body. Big plug to the MAF was inserted and plugging the hole. I am thinking of making a smoke "machine" and trying that or removing the hoses from the throttle body and plugging the holes in the throttle body and see if that clears them up. IF it does then connect one by one and keep checking the values. Lot more work but I am at a loss.
Ford F-150 - 1997-2003 :: 2002 - SES Light Came On - Showing Codes P0171 / P0174
2002 F150 - 5.4 ... So just bought this truck about a month an a half ago. No problems but the other day the SES came on. It is showing P0171 and P0174. And P0000 (almost forgot that one) was told that's generic though. Haven't really noticed a difference in the way it's running. Has been extremely cold here in WV but the only thing I can notice (or think I notice) is the gas mileage has gone down a little. After reading some on this forum I'm looking for a vacuum leak correct?
View 10 RepliesGolf V R32 :: CEL With Code P0171 And P0174 - Lean Bank 1 And 2
I am having a difficult time trying to fix my CEL issue, The vagcom scan says P0171 & P0174 Lean banks 1 and 2. I don't believe both O2's went out I have Checked and cleaned the MAF Sensor did a quick vacuum leak inspection and all seems good. I have a GIAC ST 1 and an AFE intake with noise pipe delete. I can reset it but it returns after a day or so.
View 1 RepliesFord Super Duty (1999-2016) :: 2003 F250 SD 4x4 - DTC Codes P0171 / P0174 - Loose Fitting Oily Hose?
I've had DTC P0171 & P0174 (lean in bank 1 and lean in bank 2) for a few weeks now (check engine light cued me on it). Autozone scanned it for me. It's on a 2003 F250 SD 4x4 5.4L.
My first step was to clean the MAFS. Light came back on in about 30-40 miles. I then replaced the MAFS. 30-40 miles and the light came back on.
My first thought was disconnecting the battery wasn't resetting the comp and thats why the light was comming back on.
I went and picked up an Actron cheapy OBD II Scanner today at lunch. Cleared the codes with the scanner and drove back to work.
Checked the codes when I got back (no light on but was curious) and it shows P0171 & P0174 pending.
I've checked and the dipstick is seated properly. The hoses on the air intake appear to seated properly as well. The top hose is a pretty loose fit but it was seated all the way down. The top hose was oily. Not sure if this is normal or not. Could the loose fitting oily hose be the culprit?
Also, what is the lower hose? It comes off the back of the air intake and goes to the driver side valve cover. I know it's not the PCV hose as that is on the passenger side valve cover....right?
Ford - Taurus :: Keep Getting Codes P0171 And P0174
I have a 1996 ford taurus lx dohc v6 3.0.. I keep getting codes p0171 & p0174 System Too Lean (Bank 1 and bank 2. I check for air links and i did not find any..I never got that code tell i replace the MAF sensor..
View 7 RepliesFord - Expedition :: 1999 - Error Codes P0171 And P0174
I have a 1999 Ford Expedition with 163,000 miles.The vehicle registers a service code of P0171 and/or P0174, lean mixture.The vehicle starts fine, but may stall or hesitate when first started or at red lights.While driving, there is no issue.
I just replaced the MAF sensor and the EGR sensor, but no change in the condition.In 2007 or 50K miles ago, the oxygen sensors were replaced. What could be the problem or solution?
Ford F-150 (2004-2008) :: Got Codes P0174 / P0171 / P0345 And P0349?
My truck have 4 codes p0174 and p0171 system too lean bank 1 and bank 2, and p0345, p0349 camshaft position sensor bank 1 and bank 2.
View 3 RepliesFord - Explorer :: 2003 - Idling Rough With P2196 And P0174 Codes
I've got an '03 Explorer with the 4.0L SOHC that I got for a deal on craigslist as it needed timing chain tensioners. I got that all done and it runs and drives relatively well, but it idles a little bit rough - especially when it's sitting in gear at a stop light. My go-to first attempt for idling issues is to squirt off the MAF sensor, throttle body, and squirt some starter fluid around the vacuum lines to check for vacuum leaks (though it's possible I may have missed a line or two). Neither seemed to work much. I cleared the codes, dumped some Sea Foam and fresh fuel in it and drove it around a little bit and it threw the CEL light, got about 10 mpg, and generally just didn't seem to have as much power as it should (though I have no experience with the 4.0 in a explorer, soI'm not counting that as a hard fact).
I pulled the codes and I've got a:
P2196 (O2 sensor stuck rich - bank 1 sensor 1)
(and)
P0174 (system too lean - bank 2)
That seems kinda weird to me. Bank 1 is rich and bank 2 is lean? That would make it idle and run weird, for sure, but I'm having a bit of a hard time figuring out what would cause that. I think my next step would be to check/replace the plugs, but that's more of a shot in the dark than a proper diagnosis.
Phaeton :: What These Codes Mean P0171 And P0174
So the check engline light came on, and i hooked up a basic OBD II reader to the car. Out came codes P0171 and P0174 and it read "system too lean (bank 1)" and (bank 2) respectively. What does they mean?
View 4 RepliesFord Excursion :: Check Engine Light Illuminated For Codes P0171 And P0174
Coming home from spring break towing the TT, the Check Engine light illuminates. Seems to be sputtering at idle, but otherwise OK, so we continued home.
Scanner lists the P0171 and P0174 codes. Ok, where to begin? based on internet info, started by cleaning the MAF sensor and throttle body. When I pulled apart the intake, noticed that the grommet which feeds the MAF in the air intake had become separated letting air bypass the MAF. Hence the reason for the codes.
If you get these codes, check the grommet for the wires feeding the MAF in the air intake to make sure it hasn't become separated from the intake. No more codes.
Ford F-150 (2004-2008) :: 4x4 Doesn't Engage - Codes P0171 And P0174 When Switch To 4LO
Just recently replaced the driver side 4wd actuator. When testing the system to see if it was working, I noticed that in 2wd everything seemed to be in order (wheel spun without the half shaft, no grinding noises on test drive, seemed good to go).
However, when I switched to 4hi, the dash light "4HI" would come on but the wheel still spun freely without the half shaft. When the truck was off, the wheel and half shaft spun together as they should when vacuum is released from the actuator. When I switched to 4lo, the dash light did not come on and the check engine light came on. Pulling codes revealed P0171 and P0174.
Could these codes be caused by a bad solenoid? Is the solenoid not switching the vacuum off and that's my issue? Are there other possibilities?
Camry :: 2008 LE V6 - CEL And Codes P0174 P0171
I just did an oil change at my vocational school on my grandpas car, 2008 LE V6. On the way back it threw a CEL. Codes are listed in the title. Now googling those codes i found info on other car manufacturers i.e ford, dodge etc.. But i found nothing in regards to a gen 6 camry. It seems like this code has something to do with the engine running lean. Bank 1 and bank 2. What could cause these codes and what could be a possible remedy. P0174 and P0171 were both pending and setting a cel don't know if maybe they were pending before i did the oil change.
View 14 RepliesFord Super Duty (1999-2016) :: 2005 F250 - CEL Codes P0171 And P0174
My 2005 f250 5.4 with codes p0171 and p0174. I have replaced fuel filter, MAF, Checked for vac leaks by smoke and water test.
I don't have a way to check fuel pressure on this thing since it must have been to much trouble to put that test port on the fuel rail!!!
Chevrolet - Tracker :: CEL Flickers Along With P0171 And P0174 Codes
My 2002 Chevy Tracker recently has been running poorly after consuming a 1/4 tank of gas. The check engine light comes on the scan tool reports P0171 and P0174 bank 1 and 2 lean(it's a 2.5 liter V-6). If I remove and replace the gas cap it runs better but not perfect. Once I use another 1/4 tank the symptoms return. I have noticed the cap is hard to remove lately. This has been going on for two weeks It's been to 2 garages one of them told me my catalytic converters are plugged up and wanted 2500 to fix .
View 8 RepliesFord Ranger / B-Series :: 1999 B4000 - Random Stalls / P0171 And P0174 Error Codes Come Up
I have a 1999 B4000 V6 4.0L with 78K miles on it. I recently had P0171 and P0174 error codes come up. I replaced the MAF sensor and have not had the codes return but now the truck will basically stalls out when sitting at a stop light. It does not do it all the time just randomly. It has never done it when engine is cool but only once up to temp. The idle is smooth at cold engine but begins to get rougher once warmed up (nothing too bad just noticeable). I cleaned the IAC with MAF cleaner but no joy. I reseated all plug cables at the coil but no change. RPM around 600-700 then fluctuates up a bit then truck will stall quickly( I usually cannot put other foot on gas in time to get it to increase RPM before it dies)....
View 5 Replies