Ford - F150 :: 1998 - Check Engine Light On And Error Is Bank 2 / System Too Lean
My vehicle is a 98 F150 5.4 ltr Triton. I got a check engine light on and the error is "bank 2, system too lean." I read that this can be caused by a few different things like vacuum leaks or fuel filter and so far I haven't been able to narrow down. It started with occasional shaking at idle and its happening more as time goes. When at idle it often makes a sound like slurping the bottom of a drink with a straw and shakes intermittently. The fuel economy seems to have gone down. Sometimes it seems like it almost dies in idle, but always keeps running. It runs great when I push on the gas.
View 4 RepliesFord F-150 - 1997-2003 :: 1999 - Check Engine Light Codes P0171 And P0174 Lean On Bank 1 / 2
I have a 99 f150 with the 4.2l v6 with a 5 speed 173000 miles. I picked it up not to long ago. When I first got it it had both the P0171 & P0174 lean on bank 1&2 it was also siting for a while. I replaced the fuel filter which was filled with black fuel, also changed the PCV valve, cleaned the MAF sensor, and changed the oil. I cleared the code, drove it for a little bit and the light came back on after 20 miles.
I then proceeded to replace the upper and lower intake manifold gaskets. Upon doing that i noticed that i was missing one of the linkages for the IMRC. I went to the junkyard and pulled off another linkage rod off the same motor. ordered new plastic clips, put the IMRC on cleaned everything up and began putting it back together. I also cleaned the Injectors while i had them out as well and put in new spark plugs and wires.
Put everything back together. code was cleared since the battery was disconnected. drove it and then the engine light came back on again. this time it was only the p0174. so i then both the upstream and downstream O2 sensors on bank 2, reset the code and it came back on again. I'm lost.
Ford F-150 - 1997-2003 :: 1999 - Check Engine Light Came On / Code P0171 / System Too Lean Bank 1
I just bought a 99 f150 and the check engine light came on with code p0171,system too lean bank 1. It runs and drives fine but has a strong smell of gas when I shut it off.
View 4 RepliesLexus - RX300 :: 2000 - Check Engine Light Code P0171 Bank 1 Too Lean
2000... I have a code P0171 bank 1 too lean. My question is does this exclude anything that will effect both banks? If it was MAF sensor or fuel filter would it set code and say banks 1 and 2 running too lean? In which MAF sensor ohms out correctly. I cannot view fuel trim files. I have looked for a vacuum leak with no luck. I got some cigars to try to smoke it to see if there is any vacuum leaks. Trying to narrowing what i need to checks.
View 19 RepliesChevrolet - Trailblazer :: 2006 - Check Engine Light Code P0171 - Lean Bank 1
I have a 2006 Chevy Trailblazer LS/LT 4.2 liter 2wd. I have been trying to get it smoged, but can't clear the code. P0171 - Lean Bank 1.
I've been having a parts throwing contest with it, but it has been winning and my wallet is losing.
I have changed the air filter, cleaned the MAF sensor, changed both O2 sensors, changed the secondary air valve and relay. I've done the carb cleaner spray test around the intake and vacuum lines, with no spikes in RPM.
Most recent try was a couple bottles of Techron concentrate with premium chevron gas.(still waiting to see if the code hits again)
Next steps are checking the intake bolts(to see if they are torqued) and intake gaskets, check for exhaust leaks at the exhaust manifold, and checking the MAP sensor.
Freeze frame data from the most recent hit on the code is below.
***Fuel system 1 - CL***Fuel system 2 - NA***Calc Load(%) - 30.2***ECT(deg c) - 48***STFT B1(%) - 3.9***LTFT B1(%) - 22.7***MAP(kPa) - 33***Eng RPM - 809***Veh speed(km/h) - 0***Spark Adv (deg) - 10.5***IAT(deg c) - 20***MAF (G/s) - 5.82***TPS(%) - 15.3***Air status - NA.
Passat (B5) :: Check Engine Light Came On - Code P0171 / Fuel System For Bank 1 Was Too Lean
We have a 2003 Passat 1.8t. Had the Check engine Light come on. Went down to AutoZone and hookeded up the OBDII reader. Came up with P0171, Fuel System for Bank 1 was too lean. Probable causes:
1. Fuel Pressure of MAF (If Bank 1 & Bank 2 set codes together)
2. O2 Sensor
3. Ignition Misfire
4. Fuel Injector Problem
Car has 60K - has always run well. Wife says she thinks it's running a bit sluggish. I rarely drive the car, but I think she's right. Car is not missing or running rough.
I cleared the code & started the engine; Check Engine Light is off; then looked at the codes and I find a P0171 (Pending). She tells me that the light has been on before & then gone away. So I guess it clears itself, but eventually comes back.
Ford F-150 (2004-2008) :: Check Engine Light Code Says Catalyst Deficiency Bank 2
I have a 2006 F-150 with the 5.4L. I got the check engine light and the computer says catalyst deficiency bank 2. So I assume the passenger side converter is blocked. Is there anyway to either take out the cat and replace with a piece of straight pipe and bypass the o2 sensors or take the cat out of the housing and put the housing in and then bypass the o2 sensors.
View 14 RepliesFord F-150 (2004-2008) :: Cylinder 2 Misfire And Lean Fuel Bank 1
I am getting cylinder 2 misfire and lean fuel bank 1. change the coil and didnt fix the misfire.
View 2 RepliesFord F-150 (2004-2008) :: Lean Condition Bank 1 And 2 / Random Misfire
2006 f-150 with a 4.6L. Its got 175k on the clock and ran like a sewing machine despite little maintenance other than oil changes. Recently it started running like crap; no power and missing so he borrowed a scanner and it was giving multiple codes. Here's what we have done so far, not necessarily in this order :
1.Checked for vac leaks with carb cleaner (this can be tough as engine runs crappy and hard to detect minor changes in rpms while your under the hood) no leaks detected yet
2. Changed the plugs, all looked good except for one which was heavily fouled and the electrode ate away mostly, I wasnt there and he doesnt remember which one but have a suspicion, more on that in a min
3. Changed most of the COPs and checked them all with a spark tester, all are firing.
4.Cleaned the MAF sensor with MAF cleaner
5. Checked back pressure on the exhaust by removing an upstream o2 sensor and holding a plastic fitting hooked to a pressure gage long enough to get a reading, about 1 lb idling to maybe 2 max when engine is reved, gage is not the best and fluctuates a 1/2 lb or so. Exhaust does not smell of rotten eggs.
6. Changed the fuel filter, it was terrible
7. Ran a bottle of Seafoam in the tank
8. Took the throttle body and egr valve off and checked for carbon stoppage, the holes in the egr were not blocked
9. checked the PVC valve and line and both elbows
7. checked the injector connectors with a noid light for signal, they all flash, checked the injectors them selves with a multimeter set for ohms, all about from 13.5-14.5. This should mean they arent fried but could they still be stopped up? They all sound like they are pumping when you listen with a mechanics stethoscope
9. Changed all 4 o2 sensors as this had never been done anyway
10. Compression check on cylinders, all within 10% of each other at about 180 lbs. When we pulled the plugs they all looked good except for # 7 which was heavily fouled ( I suspect the same on the original plugs) and again with a bad electrode, the part coming out of the porcelin. Intrestingly, this was an autolite plug, the rest were motorcraft, I hoped this was somehow just a bad plug but no change with a new MC plug
11. Changed the injector on #7
The scanner reads lean condition on banks 1 and 2 and random misfires on #4 and # 7 still. Per a troubleshooting tip online, we sprayed some carb cleaner in a small vac line coming off the manifold to induce a rich condition and the scanner showed the o2 sensors go to .900 which is what they are supposed to do per the guide. This means they are functioning correctly and a bonafide lean condition exists. I am leaning towards a vacuum leak around the plastic manifold under the aluminum one, maybe the gaskets but would like to rule out the egr valve, could it be the culprit?
I have even considered the possibility that the PCM is bad, though not likely. I have read to detect a vac leak you can hook the scanner up and spray the carb cleaner around on the manifold and lines with the scanner hooked up watching the scanner PID for the o2 sensors and when they detect the cleaner, they will hit that .800-1.0 meaning the engine sucked the cleaner in and you have found your leak. The exhaust smells rich. If it is a vac leak, you would think it should be a massive leak and not hard to detect, as crappy as the truck runs. I have searched the forums for days and exhausted about all I know to do.
Most important note: early on I suspected low fuel pressure as a possibility; with no schrader valve on the fuel rail and no easy spot to T into the system, we were scratching our heads how were gonna measure psi but the scanner reads absolute fuel rail pressure, gives about 40-43 psi. I hope the scanner is telling us what we need to know there, would prefer a mechanical gauge on the rail!
Ford F-150 (2004-2008) :: 2005 - Misfiring On Cylinder 7 / Running Lean Bank One
i have a 2005 f150 4x4 5.4 3 valve. it ides good but when it is in on it splutters, and also feels like dead cylinders in passenger gear. i checked the codes the other day and i had a cylinder 5 misfire. so i cleared it and today checked again and had running lean bank one and cylinder 8 misfire, then checked one more time and had cylinder 7 misfire. I am sure it is a bad coil but how do I know which one?
View 2 RepliesFord F-150 (2004-2008) :: Rough Idle And Dying / System Adaptive Fuel Too Lean Bank 1
2004 f150 fx4 w/ 5.4 .I have a code that read " system adaptive fuel to lean bank 1 " and the same for bank two. So, I got on here and did some research. Cleaned the throttle body, maf sensor, air filter, looked for vacuum leaks, changed the fuel filter and it still is running very poor at idle and it seems to be getting progressively worse...
View 2 RepliesFord F-150 - 1997-2003 :: Bank 1 Or Bank 2 Too Lean Codes At Idle When Started Cold?
I've been having this problem since I've gotten the truck about year ago. it has very high long-term fuel trims and it seems no matter what I do I cannot get them to go down my fuel trims at idle are 39 Bank1 and 33 bank2 they go down to around 12>7 while driving what could this mean. And even weirder occasionally I get Bank 1 or bank 2 too lean codes at idle when cold starting???? 1997 Ford F150 4.6 ......
View 7 RepliesFord - Explorer :: 2004 - Getting Bank 1 And 2 Lean Codes?
My 04 Explorer 4.0 has been giving me the bank 1&2 lean codes. It is the fully electronic throttle body not mechanical. It seems from reading that in 04 is when they switched to the electronic version. Here are some things I have done to resolve this. I created a diy smoke machine from a paint can and air. I found a leak by the egr.
I replaced the egr and gaskets, along with the metal part that goes into the throttle body. I replaced the pcv and hose(although it looked fine). I replaced my intake gaskets. I replaced the MAF sensor.
Before all of this my lt fuel trims were +25 for both bank 1 & 2. After doing all of this my trims did come down a little to Bank 1 +16 and bank 2 +23. I dont know what to check next!
Ford F-150 (2004-2008) :: 2005 - Engine Missing And CEL Light On
My dad is looking at a 2005 F150 2wd with the 4.6L V8 that a friend of his has. Its a 2wd XL, but has the cloth seats, the interior and body are excellent conditions. Its high mileage however, (210K), but the engine sounds good, but it has a miss and the check engine light is on. He took it about 6 months ago and had the oil changed, new belts and spark plugs, drove it very little and its been setting for sale for about 3 months.
When dad started it this evening, the engine was missing and the CEL light is on. His friend suggested he drive the truck for as long as he likes, (which he did today and he does like it) but I advised my dad to take it to a mechanic and have it checked out first, maybe even the dealer to have it checked out to be safe.... which he did today. He took it to a local Ford dealer today to get them to check it out they stated that it was a coil pack that is bad on the #2 cylinder.
They (dealer) also told him a bunch of other things that was "wrong" with it, but I think a lot of it was lies just to get him to get it fixed there and make money off of him. They said it needed an intake gasket (said it was leaking a little bit), they also said, battery and cables need to be cleaned, tranny service, coolant flush, etc, etc, etc.
Once outside the guy (tech) was bringing the truck out and my dad asked him the about that intake gasket and he acted like as if the dealer makes them act like things are a big deal, or saying they may not always need what they say. He told dad alot of those 4.6L's did that and it was really nothing to be concerned about, but I don't know.
I have a 95 Town Car with the 4.6L and am familiar with these cars, but I guess the 4.6L in these F150s are different beasts. I do know the plastic intakes on the 96+ models were issues.
Ford Super Duty (1999-2016) :: 2008 F350 - Keep Getting A Lean Bank Code - O2 Sensor?
I keep getting a lean bank code. I have cleaned tb and replaced one of the rubber lines. It only comes on when I take a good ride with the truck. Not sure what else it could be. I'm thinking O2 sensor maybe.
2008 F-350 5.4 3V. 65k miles
Ford - Ranger :: Check Engine Light Is On Saying Too Lean
I have a 2001 Ford Ranger 2WD XLT. How many oxygen sensors it has? I bought four (two upstream and two downstream) but my mechanic said there was only one downstream and installed three. However, the check engine light is back on saying "Too Lean." Is it possible that they missed one of them or that all three were simply bad?
View 1 RepliesFord Excursion :: SES Light Came On About 15 Minutes Into Drive / Code P0174 - Bank 2 Lean
After installing Banks headers and full exhaust, I took my truck for another test drive this morning. SES light came on about 15 mins into drive and is telling me P0174 - Bank 2 Lean.
So that's the right/drivers side - my list of things to go check
O2 Sensor plug on that side
The MAF
The IAC
Vacuum lines ...
Honda - Cr-v :: 2004 - Missing During Hard Acceleration And Check Engine Light Came On
During a hard acceleration to get on the freeway, the car "missed" and the check engine light came on. The shop said it was the fuel pump and replaced it. When I picked it up, they told me that I may need a new battery soon because the last start they did was hard. It worked well for me, but that day it was hard to start, but it did not seem like the battery. The shop checked the electrical system and all was good. They said the new fuel pump was faulty and replaced it. Since then, when it is over 70 degrees out (South Texas), and it is a hot start (I just drove it a while, turned it off, and try to restart within 30 minutes), it is hard to start. Could this be another faulty fuel pump? Is this some other problem? Could the shop have damaged something during the fuel pump replacement?
View 5 RepliesFord F-150 - 1997-2003 :: Check Engine Light Just Came On / Lean On Banks 1 And 2
99 F250 LD 4x4 w/5.4 - 218k .... Check engine light just came on so I had the trouble codes pulled. 071 and 074 . Lean on banks 1 and 2 . Truck is running fine as far as I can tell. I know it can be o2 sensors, pcv, maf sensor or loose vacuum line somewhere. I just put a new motorcraft pcv valve on before this happened so I rechecked the lines , all seem to be fine. Is there a inexpensive scanner that I can check the o2 sensors without just throwing money at new ones.
View 3 Replies