Ford F-150 - 1997-2003 :: Codes P0304 And P0316 - Lean Bank 1 And 2
2003 F150 v6 2wd 170k ... For a year I've only had codes P0171 and P0174 (lean bank 1 and 2). I was told it wouldn't hurt anything... I think now I should have taken care of it.
Anyway 3 weeks ago my truck started running a little rough. It was sputtering and had trouble getting up to speed, sometimes also the air switches from vent to defrost until switch gears and rpms go down. It gradually got a lot worse over 10 days while part was otw. A week ago i changed MAF and cleaned the black thing it's inside of. It started running better but still not good. I pulled my small trailer 2 days ago and it got worse after dropping the trailer.
Today checked codes at AZ and lean codes are gone and have p0304 (#4 misfire) and p0316 (crank sensor problem). Is this related.? Also Right before all the trouble I changed battery and alternator. Also i read online that MAF needed 2 weeks to relearn the way I drive to get correct gas/air ratio? Is that correct?
Also I read so many different things I needed to do during installation... Some say I need to turn key to the on position after unplugging old MAF then plug new one in... turn key to on position 10 times, Rev up engine, drive it rough for the first 2 minutes... etc. Is there a correct way to do it or is it vehicle specific?
Should I start by changing spark plugs and coils? The guy i bought it from and trust said he changed spark plugs right before I bought it. Will it ruin truck if I drive it? I've read so much but everyone says so much different things on the same topic. I'd what to start with or if this is related.
Ford F-150 - 1997-2003 :: Codes For Large EVAP Leak / Cylinder 6 Misfire / Bank 2 Lean
Here are the codes I'm getting:
P0455 - large evap leak
P1451 - main control (evap canister)
P0306 - cylinder 6 misfire
P0174 - bank 2 lean
are these all related? Or two separate issues. I have replaced all the evap lines with new lines. I have a new egr valve, and exhaust manifolds, and what should I look at 1st
Ford F-150 - 1997-2003 :: Rough Idle - Right / Left Bank Too Lean?
I have a rough idle. I have replaced upstream o2 sensors, plugs, wires, fuel filter, dpfe sensor, cam sensor, and cam synchronizer. This has only moderately improved my problem. I still have the right bank, left bank too lean codes. Could it be something as simple but hard to find as a vacuum leak?
View 8 RepliesFord F-150 - 1997-2003 :: 1999 - Check Engine Light Codes P0171 And P0174 Lean On Bank 1 / 2
I have a 99 f150 with the 4.2l v6 with a 5 speed 173000 miles. I picked it up not to long ago. When I first got it it had both the P0171 & P0174 lean on bank 1&2 it was also siting for a while. I replaced the fuel filter which was filled with black fuel, also changed the PCV valve, cleaned the MAF sensor, and changed the oil. I cleared the code, drove it for a little bit and the light came back on after 20 miles.
I then proceeded to replace the upper and lower intake manifold gaskets. Upon doing that i noticed that i was missing one of the linkages for the IMRC. I went to the junkyard and pulled off another linkage rod off the same motor. ordered new plastic clips, put the IMRC on cleaned everything up and began putting it back together. I also cleaned the Injectors while i had them out as well and put in new spark plugs and wires.
Put everything back together. code was cleared since the battery was disconnected. drove it and then the engine light came back on again. this time it was only the p0174. so i then both the upstream and downstream O2 sensors on bank 2, reset the code and it came back on again. I'm lost.
Ford F-150 - 1997-2003 :: CEL On - Bank 1 And 2 Lean?
What does this mean?? The o2 sensor(s) is reading lean?? 2001 F150 4x4 5.4
There was also an evaporator system code, but I think maybe someone left the gas cap loose? I unhooked the battery and it cleared everything. Truck started fine for a few tries. Will have it driven tomorrow to see if codes come back.
My reason for this is it was getting hard to start. I confirmed that fuel pump relay was not coming back on when cranking every time. Randomly it's fine, other times it won't start. Noticed it had CEL light, had it read at local Azone.
Don't know what to do about the "lean" issue? What would tell the pump relay to NOT turn on?
I removed the cover from the relay and inspected points, they were fine. Check with ohm meter=good. Watched it function without the cap on it. Would prime every time, but not come on when cranking every time.
Ford F-150 - 1997-2003 :: Bank 1 Too Lean Code
Well I got the ubiquitous "Bank 1 Too Lean" code this morning. Yesterday I changed out the PVC Valve, Elbow and Hose assy.
I changed out the hose from the intake to the canister purge valve on the firewall next to the master brake cylinder, that one was like dust.
Today I'm changing out the rear O2 sensors, but I may change out the fronts when they get them in (very rural area hear).
I'll keep looking for vacuum leaks and change out the MAF sensor. I hate to think it may be the intake....
Ford F-150 - 1997-2003 :: Vacuum Leak / Bank 1 Is Slightly Higher Than Bank 2
I am in the process of trying to chase down a vacuum leak on my 2003 F150 with the 5.4. I have checked all lines and cannot find it. I decided to check the long term fuel trim and noticed that my bank 1 is slightly higher than bank 2 (screenshot attached). Is this enough to assume the leak is on the bank 1 side?
View 14 RepliesFord F-150 - 1997-2003 :: 2002 5.4L - Lean Bank 2 / EGR Insufficient
My truck is a 4x4 lariat, I've replaced both dpfe valve and egr, and the intake manifold gasket. Still getting the egr insufficient code. It went away from a few months after replacing the intake manifold gasket but has returned. Where do I go from here? I vacuum tested the egr and that's working fine. Should I buy ANOTHER DPFE valve? Where do I go from here I'm desperate.
View 14 RepliesFord - Explorer :: 2004 - Getting Bank 1 And 2 Lean Codes?
My 04 Explorer 4.0 has been giving me the bank 1&2 lean codes. It is the fully electronic throttle body not mechanical. It seems from reading that in 04 is when they switched to the electronic version. Here are some things I have done to resolve this. I created a diy smoke machine from a paint can and air. I found a leak by the egr.
I replaced the egr and gaskets, along with the metal part that goes into the throttle body. I replaced the pcv and hose(although it looked fine). I replaced my intake gaskets. I replaced the MAF sensor.
Before all of this my lt fuel trims were +25 for both bank 1 & 2. After doing all of this my trims did come down a little to Bank 1 +16 and bank 2 +23. I dont know what to check next!
Ford F-150 - 1997-2003 :: 1999 - Check Engine Light Came On / Code P0171 / System Too Lean Bank 1
I just bought a 99 f150 and the check engine light came on with code p0171,system too lean bank 1. It runs and drives fine but has a strong smell of gas when I shut it off.
View 4 RepliesFord - Explorer :: Codes P0171 And P0174 - Lean Bank 1 And 2 Sensor 2
I have been getting a P0171 and a P0174 code lean bank 1 and 2 sensor 2. I have replaced all 4 censers the 171 is gone but I keep getting the P0174 and it only comes on when I am on the highway after driving around 10 miles or so i got a freeze frame of the data when it happen.
View 6 RepliesFord Ranger / B-Series :: 1998 - Codes For Lean Bank 1 And 2 - Cylinder 4 Misfire
1998 ranger 4.0L. I ran my scanner on my truck to day and my 2 bank 1 sensors seem to be bouncing between .150 and .700 but my bank 1 sensor 2 seems to be stuck at 680-720 and not bouncing, is this normal?
I did pull a code po135 heater circuit malfunction BANK 1 SENSOR 1 ...
Also I am not sure where my fuel trims should be...
My
ST1 10.0
LT1 25.0
ST2 12.0
LT2 25.0
closed loop.
When I first got the truck I pulled codes for lean bank 1 and 2 also a cylinder #4 misfire and the bank 1 sensor 1 heater circuit. I reset the codes and the heater circuit bank 1 sensor 1 popped the mil light in 5 min. So I am starting with the o2 sensors. I've not found any vacuum leaks at this point.
Ford Super Duty (1999-2016) :: Left And Right Bank Lean Codes?
What would be causing my left and right bank lean codes? Truck still seems to run fine. I have also been getting number 6 misfire. all within the past week. I know Its due for a tune up but would a simple tune up fix these codes. Also besides plugs and primary fluids what else should I be changing. I don't want to be getting to involved just the main stuff.
View 5 RepliesFord - Explorer :: 2003 V8 - CEL Came On - Too Lean Fuel Bank 1
Explorer 2003 - 116 mi V8... Has been idling poorly at about 750 / 800 rpm never stalls in idle.
Check Engine Light came on - Read code said Too Lean Fuel Bank 1
Reset codes. After a couple hundred miles Check Engine Light
Once again Check Engine Light
Same error code Too Lean Fuel Bank 1
Ford F-150 (2004-2008) :: Rough Idle And Dying / System Adaptive Fuel Too Lean Bank 1
2004 f150 fx4 w/ 5.4 .I have a code that read " system adaptive fuel to lean bank 1 " and the same for bank two. So, I got on here and did some research. Cleaned the throttle body, maf sensor, air filter, looked for vacuum leaks, changed the fuel filter and it still is running very poor at idle and it seems to be getting progressively worse...
View 2 RepliesMitsubishi - Mirage :: 1998 - CEL Codes For Fuel Trim Bank / Oxygen Sensor Bank 1 Sensor 2 And Cylinder 1 Misfire
I own a 1998 Mitsubishi Mirage with about 190,000 miles on it. The engine light has started coming on and I get three codes:
P0170 Fuel Trim Bank 1P0136 Oxygen Sensor Bank 1 Sensor 2P0301 Cylinder 1 misfire
Read more: [URL] ....
Ford Fuel System :: 2003 F150 - Service Light Randomly Comes On / Code For Left Bank Running Lean
2003 f150 supercrew with 166,000 miles on it. Daily driver. Service light randomly comes on and when code reader was put to it shows "left bank running lean." Will clear it and will randomly come back on. Truck seems to be running fine. No issues engine. Bad sensor? Or bad injector? Maybe way to test?
View 1 RepliesFord F-150 (2004-2008) :: Rough Idle / P0012 - Misfire Codes Associated With Bank 1 And Cylinder 3
5.4 3v. my last few weeks have not made me a fan. Here are the details:
I bought a 2008 F150 XL 5.4 3v with a cam phaser knock. Have done other timing jobs in past with no trouble so I was not too afraid to tackle this one. famous last words...opened the motor (shout out to the passenger side valve cover and its designer here) and found semi damaged roller follower on driver side. Worn cam lobe on the corresponding lobe and a loose chain on passenger side. proceeded to :
Change all timing components: phasers, chains, tensioners crank sprocket, all applicable bolts and BOTH cams as well as all lash adjusters and roller followers. most looked fine in fact all really did with a bit of wear on a few roller followers but only one bad one. engine didn't look to bad pretty clean.
Double and triple checked my timing chains and it was spot on. dark link on spot on crank, two dark links on the L and R dead on. put it back together. oh yes, changed all plugs with motorcraft ones, didn't even break one. did not change vct solenoids because I falsely assumed I could change the later easily if needed. they looked ok. screens intact etc... silly me for not realizing how kind Ford was in 2007 and later to necessitate removal of valve cover. I was reading a previous one on the how tos and assumed later models would be the same since it was the same sensor...
Cranked truck ran great. I mean perfect. sounded perfect. ran like a scalded cat. till it got to hot idle then it started doing its thing. rattle shake till you revved it. ran fine just wouldn't hot idle fine especially in reverse or under slight load. replaced driver side vct since ford only had one and I started on the easy side ordered the other one waiting for it. seemed to improve dramatically meanwhile I am driving this truck to test it. I drove it to work 50 miles each way and it ran great.
After a few trips it popped the P0420 light, seemed to run ok, cleared it watched it wouldn't come back. O2 sensor did seem to imply a bad cat on bank 1 since it seemed sensor two was mimicking sensor one and not staying stead like the other bank. still ran fine,
So I decided to check back pressure on the cat. I pulled sensor one out of bank one (really a joyously tight squeeze in there) hooked up my gauge and got 0 back pressure. revved it and all nothing. hooked sensor back up pulled truck out of shop and it commenced to running like crap. I mean bad. running worse than before I got it. Popping P0012 code continuously, and tons of misfire codes associated with bank 1 ..cyl 3 etc.. I tried swapping coils, pulled coils and checked spark with a tester and firing away looks like tons of good spark.
Now the weird part is : looks like bank one is dead. I can unhook any coil pack and/or injector and it runs the same and sounds like it is missing. if I unhook one off of bank 2 it almost dies or does. so bank 2 seems to be running fine. it will start and run but sounds like it missing sets flashing check engine light and backfires and stalls like crazy. I even second guessed my pressure gauge and unhooked exhaust manifold from pipe and it sounds even prettier when it backfires out of there but no change. I pulled cam sensors and cleaned it again and even tried swapping them since they looked identical but no change so I put them back.
Now I can only surmise that I am out of time somehow? or I have a gremlin perhaps? I like working on cars (usually) but this one is getting old. how do I verify what is wrong. if it is timing related how do I verify that now definitively once my marks moved I really cant figure out how to tell if it is in time? Since it has all new parts and they all ran beautifully till now. could it possibly be the vct solenoid doing all this? I plan on changing it when it comes in but surely it cant cause this many problems.. I unhooked it no change, and it does it at a cold idle and any rpm. really runs worse at idle but bad at any rpm.
Ford Aerostar :: 1996 - Lean Mixture On Bank 1
I got a CEL on my 96 4L EXT,130,000 mi. The guy that read it said it was lean mixture on bank 1. He also said a good start would be to pull the MAF and clean it and pull the EGR and clean and check it. I did that. While I was at it, I pulled the spark plugs, the IAC solenoid, purge solenoid. Going to also change the plug wires. Changed the O2 sensors 200 miles back.
I can't remember the code number. The items i have pulled and looked at seem to look OK. No plugging, if i connect a 12v source to the solenoids they react, if i pull vacuum on the EGR , the valve seat opens and closes. (Doesn't seal tight, but I wouldn't expect it to)
Question -----I pulled the DPF module mounted above but connected just below the EGR inlet pipe. How does this thing work? Is there a way to determine if it is faulty or not? It has two hoses in and a 3 prong connector on it.
FWIW---The best way I found to get the plug wires off was to push/pry "backwards" from the base of the boot, rather than pull for days until it comes off! Still a beast but a little faster I found.