Ford Super Duty (1999-2016) :: 2005 F250 - CEL Codes P0171 And P0174
My 2005 f250 5.4 with codes p0171 and p0174. I have replaced fuel filter, MAF, Checked for vac leaks by smoke and water test.
I don't have a way to check fuel pressure on this thing since it must have been to much trouble to put that test port on the fuel rail!!!
Ford Super Duty (1999-2016) :: 2011 F350 - P0171 And P0174 Codes / Spark Knock Pretty Bad
Have a an 11 f350 6.2 gas throwing p0171 and 0174. Driving the truck it has spark knock pretty bad. Ive parked it at this point. Its a tow truck so I need it fixed and back on the road. I've checked the hoses going to the pcvs they appear to be ok.... Also upon starting the truck it just sounds weak.....
View 1 RepliesFord Super Duty (1999-2016) :: Running Rough - Check Engine Light Came On And Got Codes P0171 And P0174
My 1999 F350 SD V10 that would crank but not start. I ended up checking numerous things because before it decided to truly stop running, it would run rough for a time and then be fine. The check Engine Light came on and I got the codes P0171 & P0174. Well, I bought MAF Cleaner and took the air cleaner housing off, disassembled it and thoroughly cleaned the sensor and replaced the air cleaner. I continued to get those same error codes, but before I could go any further, the truck totally died. It sat for nearly 2 months with the bed in the air as I had decided to lift the bed to check the fuel pump vs. drop the tank.
Fast forward a bit and I have since replaced the fuel pump and put $40 of Premium Gas along with Royal Purple Fuel Treatment in the tank because I figured things got stirred up and could use a bit of cleaning. I do not drive much, and during the first few trips, it ran perfectly. Then today, it started again with the rough running and trying to die if I let it idle. If I pushed on the gas, it would completely smooth out. If this were a carbureted engine, I would think the low idle was set too low, but since it is not, I am guessing it is one or more of the sensor/s that is/are causing the issue.
I am disabled and can’t play parts swap until I hit on the right part, so I was hoping that I might get some guidance here to narrow things down to the most probably causes so that I won’t go broke changing things until I hit the “right one”. The truck has 153,000 miles on it and I had bought it from a retired couple who used it to pull their 5th wheel travel trailer, so it had mostly highway miles on it. It was immaculate when I bought it and ran perfectly, needing only normal maintenance (oil changes, etc.) over the past 12 years that I have owned it. In those 12 years, I have put about 60,000 miles on it.
Ford Super Duty (1999-2016) :: 2005 F350 - Melted Air Intake Manifold Port - Code P0171 And P0174
Wife took truck out and turned around after going less then a mile, saying it was running very bad. We got this truck about two months ago at a state vehicle auction. It was a state used truck, 145,000 miles, 05 Ford F350, ext cab and 8' bed. Anyway at first I thought it was valve tap until research said an exhaust manifold. With a fog machine in rear exhaust pipe we confirmed it was leaking and replaced the exhaust manifold. Figured it was probably a good time to replace spark plugs too. Took truck for a ride and she still buck and farted.
Got a code machine and got P0171 and P0174. Couldn't find a vacuum leak, but your could hear the air being sucked in. went to local parts store, guys couldn't find leak, but they said truck sounded like a steam machine. today I made a homemade smoke machine and smoke came from air intake, figured the gaskets were bad. The pictures show what I saw when I took the gaskets off. The port that has melted is the same port were the exhaust manifold was leaking from. Am in deep "doo-doo". What caused this?
Ford F-150 - 1997-2003 :: 1999 - Check Engine Light Codes P0171 And P0174 Lean On Bank 1 / 2
I have a 99 f150 with the 4.2l v6 with a 5 speed 173000 miles. I picked it up not to long ago. When I first got it it had both the P0171 & P0174 lean on bank 1&2 it was also siting for a while. I replaced the fuel filter which was filled with black fuel, also changed the PCV valve, cleaned the MAF sensor, and changed the oil. I cleared the code, drove it for a little bit and the light came back on after 20 miles.
I then proceeded to replace the upper and lower intake manifold gaskets. Upon doing that i noticed that i was missing one of the linkages for the IMRC. I went to the junkyard and pulled off another linkage rod off the same motor. ordered new plastic clips, put the IMRC on cleaned everything up and began putting it back together. I also cleaned the Injectors while i had them out as well and put in new spark plugs and wires.
Put everything back together. code was cleared since the battery was disconnected. drove it and then the engine light came back on again. this time it was only the p0174. so i then both the upstream and downstream O2 sensors on bank 2, reset the code and it came back on again. I'm lost.
Ford Super Duty (1999-2016) :: 2003 F250 - Steering Is Loose
My steering is "loose", All front end parts are in good shape but I can move the steering wheel 4 or 5 inches back and forth without the wheels moving. Ball joints and tie rod ends are good. Truck only has 185000 miles on it.
View 2 RepliesFord Super Duty (1999-2016) :: 2005 F250 Won't Turn Over After STC Fitting Replaced
2005 6.0 F250 SD Powerstroke... Truck died on the road and wouldn't start
The symptoms were... I changed the Radiator and had the cooling system flushed... couple of weeks later it stopped while driving... did some research and talked to a few people and the STC valve seemed to be the issue... So new STC, new intake gaskets, cleaned and new EGR gaskets and I just put in a new Turbo (Ford installed it)... had a stripped bolt under the EGR cooler arm and had to remove the Turbo to get to it.... 14 days later......
Changed STC fitting and gaskets in the high pressure oil pump, IPR screen, exhaust manifold gaskets and Cleaned the EGR and changed gaskets and no start. Tried starter fluid and it turned but wouldn't stay on and the batteries died. Would you all say I'm on the right path?
Ford Super Duty (1999-2016) :: Loose Hose Under Truck Blowing Oil
I crawled under my truck today (2011 6.7 w/delete kit, straight pipe) and found a black rigid hose had signs of oil being blown out. The hose was about midway towards the back on the drivers side. There was fresh oil around the outside of the opening of the hose and some on the frame around the hose opening. I traced it back up into the engine into something that I'm not sure what it is and couldn't find it on any engine diagrams. So I've taken some pictures, what it is, what it's connecting to in the engine and why it might be blowing oil out. There isn't a lot, I haven't seen any on the ground where I park but it's obviously coming out, I guess when I drive. Pics attached.....
View 4 RepliesFord Super Duty (1999-2016) :: Codes P0172 And P0174 / Truck Bucks And Coughs / Zero Power When Driving
I have a 2008 Canadian F250 SD 5.4 triton. Its got 224000km on it and began to get the dreaded 5.4 dieseling when hot and idling. I replaced the timing chains, guides, both tensioners and crank gear. I confirmed the cam timing was correct with the crank key at 6:00 and the chains marks on the R and L. I replaced 2 coils on cyl's 2 and 3. I replaced the MAF sensor, fuel rail pressure sensor, cleaned and confirmed working the crank sensor and both cam sensors. I fixed the broken Bank 2 cam sensor wires. I changed the plugs and replaced all 4 O2 sensors.
Now the truck idles great but when driving it bucks and coughs and has zero power. I cant even get to 80km/hr. The computer now shows codes P0172 and P0174 which means the Bank 1 is rich and the bank 2 is lean. The O2 sensors are working and moving around. The back 02 sensors are both reading in the 0.8Volt range but bouncing around. The front 02 sensors are both moving from 0.1 to 0.8 constantly. The long term fuel trims are +9.5% bank 2 and -4.7% bank 1 at idle. When the throttle is off idle they become +25% bank 2 and -25% bank 1 . How is this possible and what can I do to fix this engine?.
Ford - Explorer :: 2003 - Lean Codes P0171 And P0174
2003 Sport Trac. My car was not starting, told my fuel pump, replaced twice and nothing. Found out about inertia switch and changed it, now car runs.
Before this switch blew out my car was running perfectly, no check engine, nothing. Now i have changed my fuel pump twice and put a brand new fuel filter in and soon after i get lean codes P0171 and P0174. My fuel pressure is 60psi at idle and drops to 0 after about 30 seconds when the car is shut off.
A lot of my intake is new since i did have a vacuum leak before, so i do not suspect that is it, especially since this happened after the new fuel pump. I am completely stuck as to what i should do. And i get hesitation when trying to accelerate sometimes
Ford - Expedition :: 1999 - Error Codes P0171 And P0174
I have a 1999 Ford Expedition with 163,000 miles.The vehicle registers a service code of P0171 and/or P0174, lean mixture.The vehicle starts fine, but may stall or hesitate when first started or at red lights.While driving, there is no issue.
I just replaced the MAF sensor and the EGR sensor, but no change in the condition.In 2007 or 50K miles ago, the oxygen sensors were replaced. What could be the problem or solution?
Ford Super Duty (1999-2016) :: Service Engine Soon Light On - Codes P0171 And 0174?
I have a 1999 Ford V-10 Triton 6.8L engine with 100,000 miles in my Motorhome. Service engine soon light has been a problem for the past couple months. I have replaced the O2 sensor on the passenger side and the EGR valve. After that I drove for about 300+ miles continuously and stopped to get gas. Light stayed off and I thought I had it fixed but after starting up again the light came back on. The codes are P0171 and 0174.
I had the air filter replaced before changing the sensor and valve and mechanic left the Mass air flow sensor out of the socket I had a sluggish engine and at the time I thought I sucked water into the filter, I was driving in a pouring rain, this sensor plugs into the air intake above the filter correct?) I plugged that back in. What is my next move because I reset the service engine soon light and it runs great then the light comes back on after I shutdown and restart.
Ford F-150 - 1997-2003 :: Engine Service Light - Codes P0171 And P0174
2001 F150 5.4L Triton Motor. Everything seemed o.k. then got the Engine Service Light. Checked with reader and above codes only appeared. Read numerous articles/videos and pulled the PCV hose/boot assembly and replaced the whole thing with oem part. Visually checked for disconnected tubing = none found. After this and with the new hose assembly in place I performed a reset. With the scanner still connected restarted engine and read values: ST FTRM1&2 = -.08~+2.3, both oxygen sensor voltages are varying and the LT FTRM1&2 hang around +26 and +28.
From what I understand the ST seems o.k. but the long term is WAY OUT OF WHACK. Started it up again and took carb cleaner spray and covered all the connections I could see = no change in engine rpm. No cracks in the air cleaner body. Big plug to the MAF was inserted and plugging the hole. I am thinking of making a smoke "machine" and trying that or removing the hoses from the throttle body and plugging the holes in the throttle body and see if that clears them up. IF it does then connect one by one and keep checking the values. Lot more work but I am at a loss.
Ford F-150 - 1997-2003 :: 2002 - SES Light Came On - Showing Codes P0171 / P0174
2002 F150 - 5.4 ... So just bought this truck about a month an a half ago. No problems but the other day the SES came on. It is showing P0171 and P0174. And P0000 (almost forgot that one) was told that's generic though. Haven't really noticed a difference in the way it's running. Has been extremely cold here in WV but the only thing I can notice (or think I notice) is the gas mileage has gone down a little. After reading some on this forum I'm looking for a vacuum leak correct?
View 10 RepliesFord - Explorer :: 2003 - P0171 And P0174 Codes - Rubber Elbow Begin To Collapse
2003 Ford Explorer, with P0171 and P0174 codes, common problem, as I have read. I pulled the cover over the engine off, and I immediately found the likely problem. There is a hose/connection that runs from the valve cover on the right side, about 6 inches behind the oil fill tube across and looks like it comes into the Carb. Where it turns to come into the carb is a rubber elbow. This elbow has a hole in it. Temporarily I have used electrical tape, but when I run the vehicle, I see the elbow begin to collapse. I believe the elbow is getting weak with age, plus the hole/tear doesn't work. Anyway, what i the part number, or what this is called. Hoping Advance Auto, or Napa will have it, just don't know what it is called, and can't figure out the part number. Otherwise I will pull it off tomorrow and take to advance and see if they can match it.
View 5 RepliesFord Ranger / B-Series :: 1999 B4000 - Random Stalls / P0171 And P0174 Error Codes Come Up
I have a 1999 B4000 V6 4.0L with 78K miles on it. I recently had P0171 and P0174 error codes come up. I replaced the MAF sensor and have not had the codes return but now the truck will basically stalls out when sitting at a stop light. It does not do it all the time just randomly. It has never done it when engine is cool but only once up to temp. The idle is smooth at cold engine but begins to get rougher once warmed up (nothing too bad just noticeable). I cleaned the IAC with MAF cleaner but no joy. I reseated all plug cables at the coil but no change. RPM around 600-700 then fluctuates up a bit then truck will stall quickly( I usually cannot put other foot on gas in time to get it to increase RPM before it dies)....
View 5 RepliesFord Super Duty (1999-2016) :: 2002 F250 - P0171 Code Only / Coughing And Running Rich
2002 F-250 5.4l 4x4 ... I am getting a P0171 code only, with strong fuel smell. No P0174 code. So it has to be something effecting just the one bank? Sprayed engine with starting fluid, no charge in idle. Replaced upstream O2 sensor, no change. Truck was running fine, and then just started this all at once.
View 5 RepliesFord Super Duty (1999-2016) :: F250 V10 - Heater Hose Inlets Or Outlet?
99 F250SD V10. There are two connections on the heater core at the firewall. Is there an 'inlet' and an 'outlet' or does it not matter? Put a cummins in the truck, the V10 has been out for a while and cant remember which one is which.
View 5 RepliesFord Super Duty (1999-2016) :: F250 - Smell Of Gas / Hole Rubbed In A Small Hose
Need the fuel system diagram or schematic for my truck.
1999 250 superduty v-10 Ser# 1FTNF20S1XEC67940
Every time I run it I smell gas. I changed the f/p 6mo ago. While I was working on it I noticed there was a hole rubbed in a small hose. I assumed it was a return line (smelled gas before too) and when I fixed it the smell went away until lately. I dropped the tank,yesterday and didn't see any problems. Just need to find out what hoses go where so I can replace the hoses??