Ford F-150 - 1997-2003 :: Engine Service Light - Codes P0171 And P0174
2001 F150 5.4L Triton Motor. Everything seemed o.k. then got the Engine Service Light. Checked with reader and above codes only appeared. Read numerous articles/videos and pulled the PCV hose/boot assembly and replaced the whole thing with oem part. Visually checked for disconnected tubing = none found. After this and with the new hose assembly in place I performed a reset. With the scanner still connected restarted engine and read values: ST FTRM1&2 = -.08~+2.3, both oxygen sensor voltages are varying and the LT FTRM1&2 hang around +26 and +28.
From what I understand the ST seems o.k. but the long term is WAY OUT OF WHACK. Started it up again and took carb cleaner spray and covered all the connections I could see = no change in engine rpm. No cracks in the air cleaner body. Big plug to the MAF was inserted and plugging the hole. I am thinking of making a smoke "machine" and trying that or removing the hoses from the throttle body and plugging the holes in the throttle body and see if that clears them up. IF it does then connect one by one and keep checking the values. Lot more work but I am at a loss.
Ford F-150 - 1997-2003 :: 1999 - Check Engine Light Codes P0171 And P0174 Lean On Bank 1 / 2
I have a 99 f150 with the 4.2l v6 with a 5 speed 173000 miles. I picked it up not to long ago. When I first got it it had both the P0171 & P0174 lean on bank 1&2 it was also siting for a while. I replaced the fuel filter which was filled with black fuel, also changed the PCV valve, cleaned the MAF sensor, and changed the oil. I cleared the code, drove it for a little bit and the light came back on after 20 miles.
I then proceeded to replace the upper and lower intake manifold gaskets. Upon doing that i noticed that i was missing one of the linkages for the IMRC. I went to the junkyard and pulled off another linkage rod off the same motor. ordered new plastic clips, put the IMRC on cleaned everything up and began putting it back together. I also cleaned the Injectors while i had them out as well and put in new spark plugs and wires.
Put everything back together. code was cleared since the battery was disconnected. drove it and then the engine light came back on again. this time it was only the p0174. so i then both the upstream and downstream O2 sensors on bank 2, reset the code and it came back on again. I'm lost.
Ford - Explorer :: 2003 - Lean Codes P0171 And P0174
2003 Sport Trac. My car was not starting, told my fuel pump, replaced twice and nothing. Found out about inertia switch and changed it, now car runs.
Before this switch blew out my car was running perfectly, no check engine, nothing. Now i have changed my fuel pump twice and put a brand new fuel filter in and soon after i get lean codes P0171 and P0174. My fuel pressure is 60psi at idle and drops to 0 after about 30 seconds when the car is shut off.
A lot of my intake is new since i did have a vacuum leak before, so i do not suspect that is it, especially since this happened after the new fuel pump. I am completely stuck as to what i should do. And i get hesitation when trying to accelerate sometimes
Ford Excursion :: Check Engine Light Illuminated For Codes P0171 And P0174
Coming home from spring break towing the TT, the Check Engine light illuminates. Seems to be sputtering at idle, but otherwise OK, so we continued home.
Scanner lists the P0171 and P0174 codes. Ok, where to begin? based on internet info, started by cleaning the MAF sensor and throttle body. When I pulled apart the intake, noticed that the grommet which feeds the MAF in the air intake had become separated letting air bypass the MAF. Hence the reason for the codes.
If you get these codes, check the grommet for the wires feeding the MAF in the air intake to make sure it hasn't become separated from the intake. No more codes.
Ford - Explorer :: 2003 - P0171 And P0174 Codes - Rubber Elbow Begin To Collapse
2003 Ford Explorer, with P0171 and P0174 codes, common problem, as I have read. I pulled the cover over the engine off, and I immediately found the likely problem. There is a hose/connection that runs from the valve cover on the right side, about 6 inches behind the oil fill tube across and looks like it comes into the Carb. Where it turns to come into the carb is a rubber elbow. This elbow has a hole in it. Temporarily I have used electrical tape, but when I run the vehicle, I see the elbow begin to collapse. I believe the elbow is getting weak with age, plus the hole/tear doesn't work. Anyway, what i the part number, or what this is called. Hoping Advance Auto, or Napa will have it, just don't know what it is called, and can't figure out the part number. Otherwise I will pull it off tomorrow and take to advance and see if they can match it.
View 5 RepliesFord F-150 - 1997-2003 :: Throwing Code P0171 And P0174?
97 F150 4.6 200xxx on recent rebuild. My truck is throwing P0171 & P0174.
I think I tracked it down to leaky IAC and EGR gasket. I sprayed both with carb cleaner and the RPM's dropped.
My question is, wouldn't the RPM's rise instead of drop? I was under the impression that they would go up if the gaskets were leaking. Or did I use the wrong spray?
Ford Super Duty (1999-2016) :: Running Rough - Check Engine Light Came On And Got Codes P0171 And P0174
My 1999 F350 SD V10 that would crank but not start. I ended up checking numerous things because before it decided to truly stop running, it would run rough for a time and then be fine. The check Engine Light came on and I got the codes P0171 & P0174. Well, I bought MAF Cleaner and took the air cleaner housing off, disassembled it and thoroughly cleaned the sensor and replaced the air cleaner. I continued to get those same error codes, but before I could go any further, the truck totally died. It sat for nearly 2 months with the bed in the air as I had decided to lift the bed to check the fuel pump vs. drop the tank.
Fast forward a bit and I have since replaced the fuel pump and put $40 of Premium Gas along with Royal Purple Fuel Treatment in the tank because I figured things got stirred up and could use a bit of cleaning. I do not drive much, and during the first few trips, it ran perfectly. Then today, it started again with the rough running and trying to die if I let it idle. If I pushed on the gas, it would completely smooth out. If this were a carbureted engine, I would think the low idle was set too low, but since it is not, I am guessing it is one or more of the sensor/s that is/are causing the issue.
I am disabled and can’t play parts swap until I hit on the right part, so I was hoping that I might get some guidance here to narrow things down to the most probably causes so that I won’t go broke changing things until I hit the “right one”. The truck has 153,000 miles on it and I had bought it from a retired couple who used it to pull their 5th wheel travel trailer, so it had mostly highway miles on it. It was immaculate when I bought it and ran perfectly, needing only normal maintenance (oil changes, etc.) over the past 12 years that I have owned it. In those 12 years, I have put about 60,000 miles on it.
Ford F-150 - 1997-2003 :: Code P0171 And P0174 - Vacuum Leak
I had my fuel system cleaned by the dealership last weekend and I feel like I gained 50hp+ ... Now its throwing a P0171 about a week and a half later. My computer also listed P0174 under the pending codes or whatever the section was.
2003 F150 5.4L ... I cleaned the MAF sensor a couple weeks back which stopped a rough idle and I have put some 300+ miles on it since. about 200 miles since the fuel system cleaning.
I got home and popped the hood and it sounded like a vacuum cleaner. Guess it is a vacuum leak. I might need to stop using this ford house. I swear this is the second time there was a vacuum leak(I think, first time they said it was spark gap issue). I'll be heading back in the morning now.
Ford Super Duty (1999-2016) :: 2003 F250 SD 4x4 - DTC Codes P0171 / P0174 - Loose Fitting Oily Hose?
I've had DTC P0171 & P0174 (lean in bank 1 and lean in bank 2) for a few weeks now (check engine light cued me on it). Autozone scanned it for me. It's on a 2003 F250 SD 4x4 5.4L.
My first step was to clean the MAFS. Light came back on in about 30-40 miles. I then replaced the MAFS. 30-40 miles and the light came back on.
My first thought was disconnecting the battery wasn't resetting the comp and thats why the light was comming back on.
I went and picked up an Actron cheapy OBD II Scanner today at lunch. Cleared the codes with the scanner and drove back to work.
Checked the codes when I got back (no light on but was curious) and it shows P0171 & P0174 pending.
I've checked and the dipstick is seated properly. The hoses on the air intake appear to seated properly as well. The top hose is a pretty loose fit but it was seated all the way down. The top hose was oily. Not sure if this is normal or not. Could the loose fitting oily hose be the culprit?
Also, what is the lower hose? It comes off the back of the air intake and goes to the driver side valve cover. I know it's not the PCV hose as that is on the passenger side valve cover....right?
Ford F-150 - 1997-2003 :: 1998 4.6L - Misfire On Cylinder 6 / Code P0171 And P0174
P0306 (ok #6 missfire) with P0171 & P0174 --- Do I chase electrical or fuel or both. Afraid to assume anything but probably would normally address the misfire electrical first.... Don't want to go down that 'primrose path' if others have been there first!
View 4 RepliesFord - Taurus :: Keep Getting Codes P0171 And P0174
I have a 1996 ford taurus lx dohc v6 3.0.. I keep getting codes p0171 & p0174 System Too Lean (Bank 1 and bank 2. I check for air links and i did not find any..I never got that code tell i replace the MAF sensor..
View 7 RepliesFord - Expedition :: 1999 - Error Codes P0171 And P0174
I have a 1999 Ford Expedition with 163,000 miles.The vehicle registers a service code of P0171 and/or P0174, lean mixture.The vehicle starts fine, but may stall or hesitate when first started or at red lights.While driving, there is no issue.
I just replaced the MAF sensor and the EGR sensor, but no change in the condition.In 2007 or 50K miles ago, the oxygen sensors were replaced. What could be the problem or solution?
Ford - Explorer :: 2001 - Too Lean Codes P0171 And P0174
Working on my son's 2001 sport trac. 200K miles but it has always been a great running truck.
I have two CEL codes:
P0171 System too Lean (Bank 1)
P0174 System too Lean (Bank 2)
I have found several issues so far, but have yet to get rid of these pesky codes.
So far I have changed:
- Intake Gasket - I had coolant loss which replacing this gasket fixed.
- PCV Valve and Hose - valve was damaged and the hose leaked.
- EGR Valve - Valve was leaking
- Fuel Filter
- Mass Airflow Sensor
The engine does appear to be running much smoother now, but the lean codes remain.
Ford F-150 (2004-2008) :: Got Codes P0174 / P0171 / P0345 And P0349?
My truck have 4 codes p0174 and p0171 system too lean bank 1 and bank 2, and p0345, p0349 camshaft position sensor bank 1 and bank 2.
View 3 RepliesFord - Explorer :: Codes P0171 And P0174 - Lean Bank 1 And 2 Sensor 2
I have been getting a P0171 and a P0174 code lean bank 1 and 2 sensor 2. I have replaced all 4 censers the 171 is gone but I keep getting the P0174 and it only comes on when I am on the highway after driving around 10 miles or so i got a freeze frame of the data when it happen.
View 6 RepliesFord F-150 - 1997-2003 :: Shuttering Pretty Alerting Under Light Load At 35 - 45mph - Codes P0302 And P0171
I have a 1998 F150 5.4L 4WD with 192k mi on it. Recently ( suddenly ) the vehicle began shuttering pretty alerting under light load at 35 - 45mph. The engine idle was intermittently smooth then rough. I quickly drove the truck home and ran a Trouble Code check with my Autoxray EZ-scan 4000 and found the two trouble codes P0302 and P0171. I have checked for vacuum hose cracks and found none.
Replaced the fuel filter, PCV valve, and cleaned the MAF sensor ( dirty ).
Right after cleaning the MAF sensor the idle remained smooth - but stumbling immediately when put in drive. Driving at 35-45mph still exhibits intermittent shuttering and occasional very short bursts of what feel like complete engine shut-down. This all is evident under light to moderate load .
At this point what would you recommend ? Replacing the O2 sensor bank #1 ? Or is there a possibility maybe the EGR valve is faulty - or another vacuum valve somewhere ? Intake manifold leak ?
The severe stumbling and very short complete engine shut downs would indicate that maybe the computer is failing or it's a fuel delivery issue? What rational steps to take next ?
Phaeton :: What These Codes Mean P0171 And P0174
So the check engline light came on, and i hooked up a basic OBD II reader to the car. Out came codes P0171 and P0174 and it read "system too lean (bank 1)" and (bank 2) respectively. What does they mean?
View 4 RepliesFord F-150 (2004-2008) :: 4x4 Doesn't Engage - Codes P0171 And P0174 When Switch To 4LO
Just recently replaced the driver side 4wd actuator. When testing the system to see if it was working, I noticed that in 2wd everything seemed to be in order (wheel spun without the half shaft, no grinding noises on test drive, seemed good to go).
However, when I switched to 4hi, the dash light "4HI" would come on but the wheel still spun freely without the half shaft. When the truck was off, the wheel and half shaft spun together as they should when vacuum is released from the actuator. When I switched to 4lo, the dash light did not come on and the check engine light came on. Pulling codes revealed P0171 and P0174.
Could these codes be caused by a bad solenoid? Is the solenoid not switching the vacuum off and that's my issue? Are there other possibilities?
Camry :: 2008 LE V6 - CEL And Codes P0174 P0171
I just did an oil change at my vocational school on my grandpas car, 2008 LE V6. On the way back it threw a CEL. Codes are listed in the title. Now googling those codes i found info on other car manufacturers i.e ford, dodge etc.. But i found nothing in regards to a gen 6 camry. It seems like this code has something to do with the engine running lean. Bank 1 and bank 2. What could cause these codes and what could be a possible remedy. P0174 and P0171 were both pending and setting a cel don't know if maybe they were pending before i did the oil change.
View 14 Replies