Ford Super Duty (1999-2016) :: 2005 F250 - CEL Codes P0171 And P0174
My 2005 f250 5.4 with codes p0171 and p0174. I have replaced fuel filter, MAF, Checked for vac leaks by smoke and water test.
I don't have a way to check fuel pressure on this thing since it must have been to much trouble to put that test port on the fuel rail!!!
Ford F-150 - 1997-2003 :: 1999 - Check Engine Light Codes P0171 And P0174 Lean On Bank 1 / 2
I have a 99 f150 with the 4.2l v6 with a 5 speed 173000 miles. I picked it up not to long ago. When I first got it it had both the P0171 & P0174 lean on bank 1&2 it was also siting for a while. I replaced the fuel filter which was filled with black fuel, also changed the PCV valve, cleaned the MAF sensor, and changed the oil. I cleared the code, drove it for a little bit and the light came back on after 20 miles.
I then proceeded to replace the upper and lower intake manifold gaskets. Upon doing that i noticed that i was missing one of the linkages for the IMRC. I went to the junkyard and pulled off another linkage rod off the same motor. ordered new plastic clips, put the IMRC on cleaned everything up and began putting it back together. I also cleaned the Injectors while i had them out as well and put in new spark plugs and wires.
Put everything back together. code was cleared since the battery was disconnected. drove it and then the engine light came back on again. this time it was only the p0174. so i then both the upstream and downstream O2 sensors on bank 2, reset the code and it came back on again. I'm lost.
Ford Super Duty (1999-2016) :: 2011 F350 - P0171 And P0174 Codes / Spark Knock Pretty Bad
Have a an 11 f350 6.2 gas throwing p0171 and 0174. Driving the truck it has spark knock pretty bad. Ive parked it at this point. Its a tow truck so I need it fixed and back on the road. I've checked the hoses going to the pcvs they appear to be ok.... Also upon starting the truck it just sounds weak.....
View 1 RepliesFord Super Duty (1999-2016) :: 2003 F250 SD 4x4 - DTC Codes P0171 / P0174 - Loose Fitting Oily Hose?
I've had DTC P0171 & P0174 (lean in bank 1 and lean in bank 2) for a few weeks now (check engine light cued me on it). Autozone scanned it for me. It's on a 2003 F250 SD 4x4 5.4L.
My first step was to clean the MAFS. Light came back on in about 30-40 miles. I then replaced the MAFS. 30-40 miles and the light came back on.
My first thought was disconnecting the battery wasn't resetting the comp and thats why the light was comming back on.
I went and picked up an Actron cheapy OBD II Scanner today at lunch. Cleared the codes with the scanner and drove back to work.
Checked the codes when I got back (no light on but was curious) and it shows P0171 & P0174 pending.
I've checked and the dipstick is seated properly. The hoses on the air intake appear to seated properly as well. The top hose is a pretty loose fit but it was seated all the way down. The top hose was oily. Not sure if this is normal or not. Could the loose fitting oily hose be the culprit?
Also, what is the lower hose? It comes off the back of the air intake and goes to the driver side valve cover. I know it's not the PCV hose as that is on the passenger side valve cover....right?
Ford Excursion :: Check Engine Light Illuminated For Codes P0171 And P0174
Coming home from spring break towing the TT, the Check Engine light illuminates. Seems to be sputtering at idle, but otherwise OK, so we continued home.
Scanner lists the P0171 and P0174 codes. Ok, where to begin? based on internet info, started by cleaning the MAF sensor and throttle body. When I pulled apart the intake, noticed that the grommet which feeds the MAF in the air intake had become separated letting air bypass the MAF. Hence the reason for the codes.
If you get these codes, check the grommet for the wires feeding the MAF in the air intake to make sure it hasn't become separated from the intake. No more codes.
Ford Super Duty (1999-2016) :: Service Engine Soon Light On - Codes P0171 And 0174?
I have a 1999 Ford V-10 Triton 6.8L engine with 100,000 miles in my Motorhome. Service engine soon light has been a problem for the past couple months. I have replaced the O2 sensor on the passenger side and the EGR valve. After that I drove for about 300+ miles continuously and stopped to get gas. Light stayed off and I thought I had it fixed but after starting up again the light came back on. The codes are P0171 and 0174.
I had the air filter replaced before changing the sensor and valve and mechanic left the Mass air flow sensor out of the socket I had a sluggish engine and at the time I thought I sucked water into the filter, I was driving in a pouring rain, this sensor plugs into the air intake above the filter correct?) I plugged that back in. What is my next move because I reset the service engine soon light and it runs great then the light comes back on after I shutdown and restart.
Ford Super Duty (1999-2016) :: 2001 - Running Rough - Code P0174?
2001 V10- F250.. Runs rough- had the computer put on it and was coming up with P0174 codes (I think that is right)- In any case I replaced the Mass air flow sensor- checked for any vacuum leaks visually- I did not see anything obvious.... still runs like crap.... smells like gas when idling.... anything else I can check??? The check engine light went off finally (probably due to the MAF)- but it's driving me nuts- Any hoses I have not located I need to check?
View 10 RepliesFord Super Duty (1999-2016) :: 2005 F250 - Running Really Rough When Engine Not Fully Warmed Up - Glow Plug Codes
2005 F250 6.0L ... My truck is running really rough when the engine isn't all the way quite warmed up. once the truck is fully warmed up to normal running temp it runs good. I am getting four engine codes. P0672, P0673, P0674, P0676 These codes say 2,3,4, and 6 glow plugs have a open circuit. Can this be the cause of my problem?
View 7 RepliesFord Super Duty (1999-2016) :: 2005 F350 - Melted Air Intake Manifold Port - Code P0171 And P0174
Wife took truck out and turned around after going less then a mile, saying it was running very bad. We got this truck about two months ago at a state vehicle auction. It was a state used truck, 145,000 miles, 05 Ford F350, ext cab and 8' bed. Anyway at first I thought it was valve tap until research said an exhaust manifold. With a fog machine in rear exhaust pipe we confirmed it was leaking and replaced the exhaust manifold. Figured it was probably a good time to replace spark plugs too. Took truck for a ride and she still buck and farted.
Got a code machine and got P0171 and P0174. Couldn't find a vacuum leak, but your could hear the air being sucked in. went to local parts store, guys couldn't find leak, but they said truck sounded like a steam machine. today I made a homemade smoke machine and smoke came from air intake, figured the gaskets were bad. The pictures show what I saw when I took the gaskets off. The port that has melted is the same port were the exhaust manifold was leaking from. Am in deep "doo-doo". What caused this?
Ford F-150 - 1997-2003 :: Engine Service Light - Codes P0171 And P0174
2001 F150 5.4L Triton Motor. Everything seemed o.k. then got the Engine Service Light. Checked with reader and above codes only appeared. Read numerous articles/videos and pulled the PCV hose/boot assembly and replaced the whole thing with oem part. Visually checked for disconnected tubing = none found. After this and with the new hose assembly in place I performed a reset. With the scanner still connected restarted engine and read values: ST FTRM1&2 = -.08~+2.3, both oxygen sensor voltages are varying and the LT FTRM1&2 hang around +26 and +28.
From what I understand the ST seems o.k. but the long term is WAY OUT OF WHACK. Started it up again and took carb cleaner spray and covered all the connections I could see = no change in engine rpm. No cracks in the air cleaner body. Big plug to the MAF was inserted and plugging the hole. I am thinking of making a smoke "machine" and trying that or removing the hoses from the throttle body and plugging the holes in the throttle body and see if that clears them up. IF it does then connect one by one and keep checking the values. Lot more work but I am at a loss.
Ford Super Duty (1999-2016) :: 2011 F250 XLT - Check Engine Light On / Codes P2098 And P2272 Came Up
2 weeks ago I had the check engine light come up on my 2011 F-250 6.2 XLT. Did a diagnostic check and Codes P2098 and P2272 came up. Did some research and found out the second O2 sensor on passenger side had gone bad. I replaced it with a Motorcraft O2 sensor and cleared the code. It has not came back since. But still not getting the fuel mileage I got before. What else could be wrong?
View 5 RepliesFord Super Duty (1999-2016) :: 2011 F350 - Check Engine Light And Codes P2020 And P20E8
I own a 2011 F350 dually with the 6.7 in it. It has 136000 on it and zero mods. I was driving over the weekend and the traction control light, brake light, and the ABS lights all came on and the information center displayed Check Brake System. We were towing our 5th wheel when this happened. The brakes on the pickup and trailer both work and we have no problems stopping. About every 15 minutes or so this message pops up and it chimes again. My insight is reading a U0418 code. We are stopped now and the code and alert message is still popping up without the trailer. All fluid levels are where they should be.
We are also getting a check engine light and my Insight is reading the codes P2020 and P20E8.
I can reset the codes dealing with the reductant leakage and low pressure, but not the codes dealing with the brake system.
I have had my pickup in to 2 different ford dealers for these issues and they cannot find anything wrong. I did notice that this time when the Check Brake system warning appeared that the pick up started lunging a bit, we lost power to the stereo and the windshield wipers came on. Our fuel mileage has remained the same and the pickup still tows like a beast.
Ford Super Duty (1999-2016) :: 2006 E350 Started Running Rough - Codes P0264 And P0276
I have a 2006 E350 van, just recently had passenger side injectors replaced along with dummy plugs and stand pipes. I was at the car was spraying it off and noticed it started running rough, just figured maybe some water made its way into the engine bay and something got wet as it was running great. Well its stayed that way and i am getting codes p0264 and p0276. Digging around on the net seems like its ficm or wiring, ficm is 48 volts and 13.5 volts, connectors are on tight and i dont see any wire chaffing kinda stumped. hoping its not 2 bad injectors at once.
View 2 RepliesFord Super Duty (1999-2016) :: Codes P0172 And P0174 / Truck Bucks And Coughs / Zero Power When Driving
I have a 2008 Canadian F250 SD 5.4 triton. Its got 224000km on it and began to get the dreaded 5.4 dieseling when hot and idling. I replaced the timing chains, guides, both tensioners and crank gear. I confirmed the cam timing was correct with the crank key at 6:00 and the chains marks on the R and L. I replaced 2 coils on cyl's 2 and 3. I replaced the MAF sensor, fuel rail pressure sensor, cleaned and confirmed working the crank sensor and both cam sensors. I fixed the broken Bank 2 cam sensor wires. I changed the plugs and replaced all 4 O2 sensors.
Now the truck idles great but when driving it bucks and coughs and has zero power. I cant even get to 80km/hr. The computer now shows codes P0172 and P0174 which means the Bank 1 is rich and the bank 2 is lean. The O2 sensors are working and moving around. The back 02 sensors are both reading in the 0.8Volt range but bouncing around. The front 02 sensors are both moving from 0.1 to 0.8 constantly. The long term fuel trims are +9.5% bank 2 and -4.7% bank 1 at idle. When the throttle is off idle they become +25% bank 2 and -25% bank 1 . How is this possible and what can I do to fix this engine?.
Ford - Expedition :: 1999 - Error Codes P0171 And P0174
I have a 1999 Ford Expedition with 163,000 miles.The vehicle registers a service code of P0171 and/or P0174, lean mixture.The vehicle starts fine, but may stall or hesitate when first started or at red lights.While driving, there is no issue.
I just replaced the MAF sensor and the EGR sensor, but no change in the condition.In 2007 or 50K miles ago, the oxygen sensors were replaced. What could be the problem or solution?
Ford F-150 - 1997-2003 :: 2002 - SES Light Came On - Showing Codes P0171 / P0174
2002 F150 - 5.4 ... So just bought this truck about a month an a half ago. No problems but the other day the SES came on. It is showing P0171 and P0174. And P0000 (almost forgot that one) was told that's generic though. Haven't really noticed a difference in the way it's running. Has been extremely cold here in WV but the only thing I can notice (or think I notice) is the gas mileage has gone down a little. After reading some on this forum I'm looking for a vacuum leak correct?
View 10 RepliesFord Excursion :: Running Rough And Check Engine Light Came On - P0353 And P0358 Codes
The X has been running great, well good enough, lately with no issues. I left work the other morning, and apparently the X didn't want to wake up that early. As soon as I started it up, the check engine light came on and it was running like crap. Had a bad hesitation all the way home. It feels like it is misfiring, but only under load. It doesn't do it if I brake torque it or Rev it up. Only while driving.
The codes I am getting are in the P035x family (typed that way for future searches). P0353 and P0358 are the codes I am getting (along with 4x4 codes for the vacuum solenoid...but that's the solution to other problems not relevant to this!). Being codes for the primary circuit, I popped the hood and checked out the connectors. Both connectors are fine, and tightly connected. I did notice however that cylinders 3 and 8 have other than OEM coil packs on them. These are the only 2 cylinders with those coil packs (they are white and the other 8 cylinders have black coils).
I don't want to just throw parts at it, and I'm not getting a hard miss fire code, just the 2 above. I might try to swap the coils with other cylinders tonight and see if the codes move to those cylinders. It has run like this a few times, but never set a code, and turning it off and back on has "fixed"this in the past.
And just for complete disclosure, while looking for where I saved a password, I found notes from August last year where I pulled codes, and these two codes were present then, with a cylinder 7 hard miss fire code. I replaced the c7 coil with motorcraft cleared the codes, and P0353 and P0358 went away and I haven't seen them since. The plugs are brand new and only have about 1000 miles on them (changed them in September when repairing the misfire and I don't drive it much).
Ford Super Duty (1999-2016) :: 2001 - Engine Running Rough While Accelerating?
Lately my 2001 F250 5.4 engine is running rough when I am accelerating or keeping it certain speed. It feels like it is jerking. Like if the truck lost power for a second. This will go on for few minutes. Where to start to trouble shoot.
View 8 RepliesFord Super Duty (1999-2016) :: 2002 F250 - P0171 Code Only / Coughing And Running Rich
2002 F-250 5.4l 4x4 ... I am getting a P0171 code only, with strong fuel smell. No P0174 code. So it has to be something effecting just the one bank? Sprayed engine with starting fluid, no charge in idle. Replaced upstream O2 sensor, no change. Truck was running fine, and then just started this all at once.
View 5 Replies