Ford 6.0L Power Stroke Diesel :: 2006 F250 Won't Start / No Cranking
I have a 2006 f250 superduty 6.0. The truck ran fine a week ago and than died as I was going to take it for a drive. I figured out that the fuel pump (air dog system) was not working. I fixed that and primed the pump. The truck still won't start. When it first happened the truck would crank but not start. Now all I hear is the starter but no cranking. Both filters could be replaced. The bowl to the upper is dry when I take the cap off. However fills up when you turn the key on. I'm not sure what else to try and I need to get this truck started.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 Cranking For A Bit Of Time And Refuses To Start
I have a 1999 f250 7.3 psd. it cranks and will not start, it use to crank for a bit of time and then start and now it refuses to start. If I leave the key in start position for like 30 seconds it use start and now it wont. I am thinking it is something with the glow plugs?
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2003 - When Cranking Low Oil Pressure Comes Up On The Gauge
OK so here is what is going on in my world. I have an '03 F-250 6.0 Crew Cab 4x4, with an Edge programmer and 4" MBRP exhaust. About 3 years and only 20,000 miles ago I changed out the HPOP, O-rings on the rails, all new O-rings on the injectors, blue spring in the fuel pump, IPR valve, EGR valve and a number of other new seals in my high pressure system. The truck has run great since then. I cleaned out my turbo about a year ago and it has been like new.
Now for the fun part. About a month ago it has been cranking a little longer when hot than it should, but not too bad. About 2 weeks ago even though it starts fine in the morning, it is just completely gutless out of the driveway until about a block away the turbo spools up strong and it runs great. It has run perfectly during this time once it is warmed up a little bit. Saturday it left me stranded in a parking lot cranking with no start. It had been sitting for about 2 hours.
I got towed home and plugged in my SGII and it shows my ICP at 345 when cranking hot. Once cold it starts up and runs great, but won't start again once hot. I changed out my IPR valve with a used one that I had on the shelf that I took out when I did my HPOP. No change. The FICM has 47 volt while cranking and 49 when just ign is on. Batteries are very strong and it has a new starter. When cranking the low oil pressure comes up on the gauge. Not sure where to start and I am frustrated. I have had this truck for 9 years and it is in great shape. It only has 138,000 miles.
Ford 7.3L Power Stroke (1999-2003) :: F250 - Misfire When Cold / Lost Oil And Long Cranking
I've got a99 F2 50 super duty with a 2000 2001 motor. I got the truck in the beginning of last winter so this is my first summer with it.
When I first got the truck there are injector issues with the truck. Since I fix the issues there has been little problems out of the truck however it's still suffered misfires when Cold but once up to operating temperature it was fine. Yesterday I had to go with a friend before leaving for the trip I checked the oil it was full and appeared normal the trip was about 150 miles. I came home park the truck after everything was done. This morning I came out started the truck everything acted as it should... truck fired right up everything was great went and dropped off my trailer at the yard come back got fuel when I come back out from paying for the fuel the truck took about 30 seconds to fire up I checked my gauges and torque pro and everything seemed normal. So on my way I went.
I drove about 10 miles on the highway to the place I had to be when I got done doing my business I came back out to start my truck and it did the same thing this time however it took longer to start I managed to drive about a mile down the road when I noticed my old pressure gauge flickering and my Oil pressure light on I immediately shut it down and coasted into O'Reilly's parking lot I check the oil in the truck and it was empty according to the stick I added two whole gallon.... With it filled back up down the road I went. So currently the truck is still suffering from a long hard starts it takes 30 to 45 seconds before it all actually fire up once it fires up everything appears to be fine however the truck is slowly smoking a bluish black color... It's never done this before however I've never had this truck in the middle of summer when it's real hot out I don't think this is normal.
The truck doesn't appear to be down on any power actually it, acts as if it might've picked up of some power it is felt real peppy today compared to other days. Also I might note that about a week or two ago I started smelling diesel like either really rich diesel or raw diesel wasn't too bad but I just got whiffs of it for now and then. Now there is a burn oil smell present from the exhaust. Like I was saying earlier when I first got the truck I had to service the injector O-rings... I was told that the miss firing when cold was caused by the Poppitz sticking. The misfire hasn't been present since it got a little warm outside like I was saying it was only when the vehicle is cold.... Just thought I would mention the injector issue not sure if it's relative or not..... My thoughts are it's back to an injector issue or O-rings or possibly did I wipe the motor when it ran out of oil. I am not aware of where the oil went as there is been no leaks or drips.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 Not Turning Over After Injectors Replacement
So I replaced all the rings on my injectors . After putting them back in turned the engine over 5-7 times by hand with the glow plugs out. Then I turned it over with them out as well with the valve covers off. After than I installed everything back in. Now is my problem. I've turned it over 5 times and no luck. Not even on turn over. The oil light keeps coming on?? The indicator doesn't move up at all. It will go up and come down ? Is something wrong with the hpop? Should I keep cranking? Gotta to charge the batteries now..
2001 f250 7.3
Ford 6.0L Power Stroke Diesel :: Starter RPM When Cranking?
I've been trying to figure out a slow start condition on my 06 F350. What should the starter rpms be when cranking? My scanguage reads 180. Does this sound low? Batteries are new.
View 9 RepliesFord 6.7L Power Stroke Diesel :: Cranking With No Fuel?
Cranking without fuel is probably never a great idea - but it happens - maybe after repair or when someone runs out of fuel, etc....
Is it any harder (worse than usual) on these Bosch fuel pumps than any other vehicle? I realize that the closer tolerances and the very high pressure might make things a little more fragile in a "no fuel" situation...
This question came from a discussion that I was in (maybe beer was involved) a couple of days ago... Of course we had 4 different opinions... I would like to know the facts - if someone is more qualified then us "redneck mechanics"
Ford 6.0L Power Stroke Diesel :: 2003 F250 - No Start After EGR Delete
Just did an egr delete, oil cooler, icp sensor and exhaust on an 03 f250 6.0l. got it all back together and it cranked up and ran for about 30 seconds then stumbled and died. read to pull out the ipr sensor and check it and it had a piece of debris on it covering the screen. took of the debris and still no start.
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 - Not Enough Pressure To Start
I have a 2003 F-250. For 8 months now we have been trying to get my truck to start. We have replaced the High pressure oil pump, Oil cooler, PCM, Main wiring harness, FICM, Injectors,, ICP, and IPR. Still we are not getting enough pressure to start the truck. What is happening is the pressure will get to about 340 and will not increase from there. If we are to disconnect of one the connectors from the FICM the pressure will reach 640. Now we are able to get the truck started with ether, but will not remain started. As of right now we are still trying to figure out what is causing this problem?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 Cranks Then Stops
So I have a 03 f250 6.0 with 285,000 miles, when I shut the truck off and let it sit for like 20 mins and go to restart it, it cranks then just stops and I hear what I think to be the starter still turning till I let off the key. It'll do this for a while sometimes. So what do y'all think it could be? P.s I know it's very bad for the truck, but I have ran out of fuel about 9 times on the stock pump because my fuel gauge is off, and after the most recent breakdown is about the time it started.
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 - Engine Won't Fire Up
So I've had my 2003 F-250 power stroke 6.0 for over a year now and replaced the oil with AMS oil which is good for 50,000 miles to a year as well as the oil filter which is guaranteed the same thing. I've only put 5,000 miles on it since I've owned it and made sure to let the engine heat up before going anywhere as well. Recently my engine bogged down and then had problems starting I was able to limp the last 2 miles to work but haven't been able to get it running since.
I replaced the camshaft position sensor and it fired up but once it was running it the rpm gauge dropped below 1000 RPMs it would stall out. Before it didn't have any smoke coming from the engine compartment however now when it starts it does. Is this because there's oil the possibly leaked onto something or fuel? What do I or should I look at to get it fixed?
Ford 6.0L Power Stroke Diesel :: Won't Start - Voltage From 11.5 To 10.5 While Cranking?
Scangauge reads icp ok. Ipr ok. Fmp voltage is all over the place from 42 down to 2. Flp is also all over the place from 11 down to 2 volts. And no Sync. Load checked batteries well. Voltage is 11.5 down to 10.5 when cranking. Fuel good. No pre warning signs. Parked running good. I have read tones of forums but none with 3 issues. Could it be the relay?? Would a bad ficm show no sync on cranking?? Why is my flp voltage so up and down.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Cranking But Barely Tries To Start
Finally got everything buttoned up, and truck was going for it's first drive today. Started cranking, and it just barely tries to start, and then nothing until I cycle the key again. Doesn't even give me a full Vroom, Just like a Vro- and then back to cranking.
I've had it started and running a few times, so something has changed. And to add to the fun, something between my tablet, my torque pro app, and my dongle isn't playing nice. Tablet just won't see the dongle. So I get to figure that out too.
Ford 6.0L Power Stroke Diesel :: 2003 F250 - A/C Compressor Intermittent Working
I have a 2003 f250 6.0. Recently, I have noticed that my air conditioner will work at first but once the compressor cycles off it does not come back on. I end up having to turn the a/c controls to off and wait about 5 min then turn them back on and it will work for a about 5 min then blow warm air again.
This happens more when towing rather than just driving around. I have changed out the sensor on the canister but it was no dice. The system is charged to the correct level according to my gauge. This occurs more often on hotter days than any.
While the truck has been running and the system is malfunctioning, I have crawled under the truck and noticed the center wheel of the compressor is not turning but can be turned by hand. Do I need a new compressor or am I missing something else that would be simpler?
Ford 6.0L Power Stroke Diesel :: 2003 F250 - Fuel Gauge Inaccurate
I just got a 03 f250 cc lariat with the 6.0, the truck sat for a month and a half before I picked it up, I got in started and the fuel gauge showed over half and the miles to empty was accurate and the temp was as well, about half way home the gauge dropped below empty and the fuel light turned on, then the miles to empty went up to 455 and the temp showed 67 when it was 92 out. I have read other post with these problems but no one has a solution, people have recommended techron for the fuel sender, but techron is not recommended for diesel...
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 Truck Will Not Start / No Crank
I drove my 03 f-250 to work Monday everything was good no issues. At end of my shift truck will not start . turn key dash lights up glow plugs cycle turn to start nothing . Does not turn over. after some checking batteries are good. Starter will crank if i manually engage it but truck will not run even with jumping starter with ignition turned on . hooked scanner up says cannot communicate. Checked fuses etc fuse #31 has no power to it (trans range selector and starter relay)question is where to look next?
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 Truck Just Died While Driving
I am working on an 2003 F-250 6.0l. The truck just died while driving. No restart. Plugged in my scan tool and I am not getting any High pressure oil. Is there anything other than the Hpop I should be looking at. I know it is a big job to replace the hpop so I don't want to overlook something simple.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 - Intermittent Hesitation While Trying To Accelerate
Finally registered on this site after hearing good things from others who are currently on here. Been a 6.0 PSD owner since buying the truck since new in 2003-F250 CCSB. I have done regular maintenance on it and have had a good run until recently. Everything is stock on the motor and currently has 229 000 miles.
I will describe my current problem: I have borrowed my brother's tablet and have the following numbers from the Torque pro app. While trying to accelerate it now has a hesitation and seems to not have the power.
At idle: 630 psi HPOP, 24 % IPR, 47 volts FICM, ICP volts .1
Trying to accelerate on at highway speeds: 1230 psi HPOP, 83% IPR, 47 volts FICM, ICP volts 2.6
Also, sometimes when starting the truck it seems to rev extra high for a split second. My brother says I may have a high pressure leak on the system. What I should check first?
Ford 6.0L Power Stroke Diesel :: 2003 F250 - How To Reset Average MPG Calculator
I have a 2003 F250 4X4 PSD. How do I reset the "Average MPG" calculator? I asked because I have doubts that it is functioning properly.
Example:
Zero load, high-way driving.... the display shows 14.4mpg.
Zero load, in-town driving... the display shows 14.mpg.
1,000 lbs in the truck, pulling 4,000 lbs on the high-way for 600 miles (each way)..... the display shows 14.2mpg.
And since I've returned from the trip mentioned above with the 5K of load, it has not changed from displaying 14.2mpg.... even though I am back to high-way driving with zero load... been through 6 -8 tanks of fuel.
My expectation is that when I am traveling without a load on the high-way that it should get the best MPG. Subsequently, when I am pulling a load, utilizing the "Tow" function (without engaging O/D), that it would get worse MPG. However, it appears there is virtually no difference registered / displayed in MPG regardless of how I drive or what I tow.