Ford 6.0L Power Stroke Diesel :: 2005 F250 Crank But No Start - Low Pressure?
2005 F250 To date this has been done, some at different times. ARP studs, OEM head gaskets, heads machined, oil cooler replaced, new fuel injectors, reman'd HPOP w/IPR with STC fitting, EGR delete, 4" turbo back and SCT x3 tow tune.
We originally had a leaking injector that gave us issues (Thread is here) but we pulled the cab and went through the motor, installed studs etcetera.
After the rebuild we ran it approximately 1K miles and it ran great, then one day towing a '65 C10 on a 20' flatbed it shut off while cruising down the road, crank no start on the side of the road, scanguage showed ICP was too low to fire the injectors so we towed it back to the shop and replaced the HPOP, still low ICP.
What's the next step of diagnosis? I'll have ICP numbers by Monday, it's been several months since all this happened and I'm currently out of state trying to diagnose. If i remember correctly the ICP numbers were low teens or 20's. I don't know for sure but I don't think we replace the standpipe or dummy plugs when we had it apart, could that be the issue?
My thoughts are either we have a leak in the high-pressure side or low pressure isn't supplying enough oil to build pressure, so in theory, we would want to check low pressure first, correct?
Ford 6.0L Power Stroke Diesel :: 2003 F250 - No Start After EGR Delete
Just did an egr delete, oil cooler, icp sensor and exhaust on an 03 f250 6.0l. got it all back together and it cranked up and ran for about 30 seconds then stumbled and died. read to pull out the ipr sensor and check it and it had a piece of debris on it covering the screen. took of the debris and still no start.
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 Truck Will Not Start / No Crank
I drove my 03 f-250 to work Monday everything was good no issues. At end of my shift truck will not start . turn key dash lights up glow plugs cycle turn to start nothing . Does not turn over. after some checking batteries are good. Starter will crank if i manually engage it but truck will not run even with jumping starter with ignition turned on . hooked scanner up says cannot communicate. Checked fuses etc fuse #31 has no power to it (trans range selector and starter relay)question is where to look next?
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 - No Crank / Start - All Gauges Shut Off
I have a 03 f250 6.0 had it for 2 years never had a problem. Last week I went out and started it to warm it's up as it is cold out here and it started fine I then noticed some thing hanging down under the dash so I started tucking it up under there and it arced and all gauges shut off and the truck shut off. So I took the panel down and it was the biometric pressure sensor that was hanging and the previous owner had a remote start on there that I never knew about and 2 wires on the sensor were stripped and not taped as well as some others. I checked all fuses and relays all working good tested fuse box and everything good there, replaced bio sensor and still nothing turn the key and try to start it and it does nothing injectors, don't precycle fuel pump doesn't run and starter doesn't kick in. I jumped starter off the wire on fender and it turns over but still doesn't start. Also I think it's the ecu but don't want to buy another one if I'm not sure if that's the problem.
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 Won't Start After Replaced All 3 FICM Connectors
I have an early 03 F250 6.0 that won't start after I replaced all 3 FICM connectors, also # 8 injector pin and connector. It has been almost impossible to start before the repair.
I checked the grounds on
Pins #1 2 3 22 they were all .5 ohms
Pin #32 was 1.0 ohms.
Pins #7 27 were 12.7v ( battery voltage)
I have double checked all pin connections and wire colors, they are in the right holes, I haven't done any cranking voltage tests, as I am alone. The FICM has 48.2 v.
Ford 6.0L Power Stroke Diesel :: 2003 F250 Struggles To Start When Crank First Time
I am trying to diagnose an issue with my 2003 F-250 6.0L PSD.
The first time I crank it everyday, it struggles to start. Beyond that, it seems to run fine and not have issues cranking throughout the day.
I've recently replaced both batteries, the FICM, the fuel filters and the FI wiring harness. What could be the issue?
The video shows exactly what I deal with every morning.
YouTube - 2003 F-250 Cold Start Issue ....
Ford 6.0L Power Stroke Diesel :: 2003 F250 Crank But No Start - Popping Noise Out Of The Intake?
My 2003 f250 6.0l just up and quit. It make a popping noise out of the intake when cranking. I am getting 1150 psi at the icp and ipr is at 62% which seems high to me. The FICM voltage seem fine unless the batteries are drained and I am getting FICM sync. I replaced the HPOP, ICP sensor and IPR about a year ago. I recently replaced the air conditioning compressor and power steering pump. I am at a bit of a loss. I did pull the IPR and everything looked fine.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 Just Start / Misfire / Lope / Jump And Buck
2003 F250 crew cab 6.0 ... Where are the main problem areas on the ficm wiring harness truck will start and run great at times and at times it just start and misfire lope jump and buck it has to be a short I've changed the icp and crank / cam sensors some days it runs fine had issue with alternator replaced it.
View 10 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 - No Start / Lost The Upper Turbo Hose
I have an 03 super duty with the 6.0, came back from vacation with my 5th wheel in tow. Lost the upper turbo hose twice on way home. Managed to get it rigged and made it home and parked it. a week later went to uncouple and move the truck and had some very strange issues. Started fine but could barely make it up driveway (no trailer at this point). No power, felt like when turbo hose came off. Got it moved and checked turbo hose and all was good?? Went out a couple days later and no start.
Checked all relative fuses and relays and all checked good. Jumped starter solenoid and starter worked fine. turned key on and jumped quick connect on right side of engine compartment to battery and it fired right up and ran. Jiggled shifter around in park and neutral and nothing. BTW I always here the relay clicking and swapped with one of the others just to be sure, same thing. After looking on the internet for a day and a half thought maybe a NSS in the tranny but I think I have the 5R110 that does not apply??
Ford 6.0L Power Stroke Diesel :: 2006 F250 - Oil Pressure Only Going To 350 PSI / Crank Longer When Cold
I have a 2006 f250 6.0 203,00 miles. At 196,000 miles turbo went out, bought power max turbo, redid head gaskets with studs, had heads shaved flat, replace oil cooler with ford part, egr delete, custom tune, aftermarekt 48 Volt FICM.
Truck ran great until 1 day didn't start. had to let truck cool down and then it stared oil pressure was only going to 350psi. drove home fine, shut it off and wonted start hot. drove it a few times after that just let truck idle. Then it started to crank longer when cold. Replaced dummy plug and stand pipe on drivers side only. Then truck was ok for a few drives then started to get a studer sometimes when idling. It got worse then was getting a misfire cyl 1 then, truck died 1 day turning around and would only build a 200 psi.
Replaced stand pipe and dummy plug on passenger side, and IPR, now getting misfire on cyl 8 and P2284, truck runs like crap, bad idle, rpms weird/gas pedal. idle is higher than it should be. when truck is first started shacks very bad, engine very nosiey. ICP 1046 psi(1.27Volts)Desired 637.9, idle and ipr 14.84, truck idles ok, when u punch gas revs up and comes back down, misfire gets worse with rpm.
Then icp goes to 870(2.23 Volts)Desired 870 and doesn't change when getting on the gas and ipr 32.42, punch it and rpms go up more then come back down. Truck starts to shake again. Could running it for so long with bad oil pressure or to much air wreak the injectors? When cold can shut off injector 7 or 8 doesn't change idle like all others do. Once warm 7 or 8 does make a small change in idle. If i command ipr to 20% idles fine, but icp no change from 32.42% to 20%...
Ford 6.0L Power Stroke Diesel :: 2006 - Won't Start When Hot - Oil Pressure?
Background: My 06 started up and ran fine until #7 injector took a crap.I had the injectors replaced with 155/stocks from warren.
Well no we're having an issue with a hot no start. Starts and runs just fine cold but once up to temp and you shut her down you can't start it again till it cools. Air tested it 3 different times can't find any leaks. Swapped out the ipr with a new one my mechanic had just to see and no change, unplugged it and no change.
What it could be. When warm and trying to start it only gets 300psi. The only other thing i can think of is hpop, but to go just like that without any trouble before hand has me puzzled.
Ford 6.0L Power Stroke Diesel :: 2004 - No Oil Pressure At Start Up
I have a 2004 late model 6.0. My son was driving it and parked it in the road told him move it and it wouldn't start. I got it to start and it ran for about 10 seconds. I pushed it in the drive way and left it over night. In the morning there was oil on the driveway. I found that there was the wrong oil filter put in and there is no oil pressure at start up and no oil entering the filter housing. Where to start would be great. I am going to get a Scangauge II to get more information. Could be the ICP?
View 4 RepliesFord 6.7L Power Stroke Diesel :: 2011 F250 - Water In Fuel / Sighs Of Rust In High Pressure Pump?
Recently my 2011 F-250 Diesel with 21,000 miles seemed to start hard one morning. After starting the truck it ran well that day and started fine. The next morning it would not start. Had it taken to the dealer and they went to work. Started at the fuel filters and replaced low pressure fuel pump. Thought a piece of the defective pump had moved up fuel line. Removed high pressure pump and found signs of rust. All regular service intervals have been met. Didn't see this coming. No water in fuel light or other warning.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 - No Oil Pressure At Idle
2003 6.0 diesel with 200,000 miles runs good start easy but does not show oil pressure at idle (intermittent problem that has been occurring more often). It has ford oil filters and ford oil with about 3500 miles on the oil. The check gage will come on and the oil pressure drops out if you give it some throttle it comes back but will drop out again at idle. But like I said the truck runs perfectly fine and the icp shows pressure all the time.
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 Error Codes - Injector Control Pressure Sensor Circuit Intermittent
I bought my truck 2 month ago. I use it for commuting, only short trips now ( 10 min ). After about 2 weeks the Check Engine light came on. The truck is running fine, no problems I believe, starts easy. After another 2 weeks, the CEL disappeared. Another week, and the CEL came back on and it`s there since. I have a code reader, these are the codes and meanings according the manual:
P0299 - Turbocharger "A" underboost condition
P2286 - Injector control pressure sensor circuit high
P2287 - Injector control pressure sensor circuit intermittent
P0299 Pending - same as first but with "pending" status
This is my first diesel and my first turbo charged engine. Is this a common problem? How serious? It`s a bit strange that the error came up before but disappeared. Can that happen just because of the short trips I`m making? I`m planning a long trip soon with towing my trailer, so I want to make sure the truck will not break down during the ride.
Ford 6.0L Power Stroke Diesel :: Crank But No Start - HPOP Brand New Still No Pressure
05 excursion with 04 motor. 290k miles. Had a crank no start issue. Pressure tested hpop only got 450 pressure. So got a brand new on from ford. Also did standpipe, and dummy plugs. After forever and day of cranking truck fired up. Sounded great let it sit for 30 min. Took it out for ride, mile down the road lost all power. Alternator was bad, replaced that and battered just to be safe. Now truck won't fire and have zero pressure. Something that could of been tripped during power surge?
View 8 RepliesFord 6.7L Power Stroke Diesel :: 2012 F350 - Low Fuel Pressure - No Start
I am new to the FTE world but not to diesels my 2012 f350 is my second diesel and a couple weeks ago I got home from work and fell asleep and forgot to plug in my pickup and it gelled up (was about 15degrees when I fell asleep and -20 when I woke up) so all the filters were replaced and everything was good after that for about a week, then my fass platinum pump started blowing the 30a fuse every 10 seconds and The pump itself smelled burnt so I replaced it with the same style and size of pump and the pump is good now but the truck is a no start it has thrown codes p2291, p0089, p0091, and p228e. It has 4inch straight exhaust, fully deleted (def and egr), h&s tuned, fass platinum 125 lift pump.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 - ICP Pressure Low And FICM Not Syncing
I have a no start on my 2003 6.0. What I've discover is that I have two issues, ICP pressure is low and the FICM is not syncing. My plan of attack is to fix the sync problem first then the ICP issue. FICM main power is good holds at 47.32 during crank but it has no FICM sync, I've check the camshaft position and crankshaft position sync status and it returns a value of in sync, it also reaches a max rpm of 257 during crank. Given those two values I think the cam and crank sensors are good. I did a visual inspection on the wire harness and can find no chaffing, shorts or hard bends. I think I either have a bad PCM or FICM. How I can narrow it down to one of the two?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 - When Cranking Low Oil Pressure Comes Up On The Gauge
OK so here is what is going on in my world. I have an '03 F-250 6.0 Crew Cab 4x4, with an Edge programmer and 4" MBRP exhaust. About 3 years and only 20,000 miles ago I changed out the HPOP, O-rings on the rails, all new O-rings on the injectors, blue spring in the fuel pump, IPR valve, EGR valve and a number of other new seals in my high pressure system. The truck has run great since then. I cleaned out my turbo about a year ago and it has been like new.
Now for the fun part. About a month ago it has been cranking a little longer when hot than it should, but not too bad. About 2 weeks ago even though it starts fine in the morning, it is just completely gutless out of the driveway until about a block away the turbo spools up strong and it runs great. It has run perfectly during this time once it is warmed up a little bit. Saturday it left me stranded in a parking lot cranking with no start. It had been sitting for about 2 hours.
I got towed home and plugged in my SGII and it shows my ICP at 345 when cranking hot. Once cold it starts up and runs great, but won't start again once hot. I changed out my IPR valve with a used one that I had on the shelf that I took out when I did my HPOP. No change. The FICM has 47 volt while cranking and 49 when just ign is on. Batteries are very strong and it has a new starter. When cranking the low oil pressure comes up on the gauge. Not sure where to start and I am frustrated. I have had this truck for 9 years and it is in great shape. It only has 138,000 miles.