Ford 6.0L Power Stroke Diesel :: 2005 F250 - Engine Change Out Now The Truck Will Not Start On Hot Crank
So, we have a 2005 ford F 250 6.0 diesel and we had the engine changed out from a 2006. Now the truck will not start on hot crank. It will start up normal when cold. So dummy plugs and stand pipes were changed out as well as the oil pump and turbo from the 2005 engine because they were still perfect. What else could be causing the truck not to start up after truck is hot. Does the engine number have anything to do with it? Or anything electrical
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 - Truck Won't Crank Anymore After ICP / Oil Cooler Repair
2003 250 superduty 6.0 ... I had to do the icp sensor. I went in from the top and discovered that the oil cooler was failing also. Replaced the icp and the oil cooler. Got it all back together. It would crank but wouldn't fire up. it did try for a about a tenth of a second. that's as close to firing as it got. The shifter has been loose. i ran it through the gears and the back into park. now it won't even crank.
Took the starter in to have it tested. it tested fine. Went to put it back on the truck. With no real force tightening the electrical connection it just snapped off the solenoid. put a new solenoid on it. Still no crank. Checked all related fuses and relays. They all seem to be good.
When I turn the key to on I get the buzzing noise and everything. Been through a lot of the no start check list. I don't have the ability to quite test everything. But what i can check. i do have an obd2 scanner. I cleared the code for the icp. I don't have any other codes showing. I have tripled checked that. After the weekend I am going to have to give up and take it in I think.
Ford 6.0L Power Stroke Diesel :: 2003 F250 - No Crank / Start - All Gauges Shut Off
I have a 03 f250 6.0 had it for 2 years never had a problem. Last week I went out and started it to warm it's up as it is cold out here and it started fine I then noticed some thing hanging down under the dash so I started tucking it up under there and it arced and all gauges shut off and the truck shut off. So I took the panel down and it was the biometric pressure sensor that was hanging and the previous owner had a remote start on there that I never knew about and 2 wires on the sensor were stripped and not taped as well as some others. I checked all fuses and relays all working good tested fuse box and everything good there, replaced bio sensor and still nothing turn the key and try to start it and it does nothing injectors, don't precycle fuel pump doesn't run and starter doesn't kick in. I jumped starter off the wire on fender and it turns over but still doesn't start. Also I think it's the ecu but don't want to buy another one if I'm not sure if that's the problem.
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 Struggles To Start When Crank First Time
I am trying to diagnose an issue with my 2003 F-250 6.0L PSD.
The first time I crank it everyday, it struggles to start. Beyond that, it seems to run fine and not have issues cranking throughout the day.
I've recently replaced both batteries, the FICM, the fuel filters and the FI wiring harness. What could be the issue?
The video shows exactly what I deal with every morning.
YouTube - 2003 F-250 Cold Start Issue ....
Ford 6.0L Power Stroke Diesel :: 2003 F250 Crank But No Start - Popping Noise Out Of The Intake?
My 2003 f250 6.0l just up and quit. It make a popping noise out of the intake when cranking. I am getting 1150 psi at the icp and ipr is at 62% which seems high to me. The FICM voltage seem fine unless the batteries are drained and I am getting FICM sync. I replaced the HPOP, ICP sensor and IPR about a year ago. I recently replaced the air conditioning compressor and power steering pump. I am at a bit of a loss. I did pull the IPR and everything looked fine.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Truck Won't Start / Crank After Oil Cooler Rebuild
Had to do the icp sensor originally. went in from the top and discovered my oil cooler was failing too. so i did that. with weather (too tall to fit in the garage) and life getting in the way it's taking me 2 months a little here n there to actually get it done so she's sat for a while. yesterday was moment of truth to get it started again. the batts were old before i started working on it. so i replaced those yesterday.
I've tried and tried to get it to start and it won't turn over. it did for one tenth of a second try. nothing since. I saw that my shifter wasn't exactly in park so i wiggled it and tried to crank it again and now it won't even crank. I have a feeling somehow the transmission isn't reading in park or neutral so it's refusing to crank. I really don't want to tow it.
Ford 6.0L Power Stroke Diesel :: Truck Won't Start / No Crank - Code P2285
So the truck wont start, no crank no nothing all lights work etc. I am getting the icp code. I replaced the icp and the pigtail about a year or so ago what should I be looking at?my icp voltage is .22 volts with the koeoff. While trying to crank it I get no change in voltage. My ipr is at 14.8 and the ficim is at 47. Also when I unplug the sensor it still does nothing...
View 8 RepliesFord 6.0L Power Stroke Diesel :: Crank No Start - Truck Sounds Like It Is Almost Firing Up But Still Cannot Get It To Run
Had extreme cold weather here and I left my truck unplugged for a couple of weeks. Started fine but stalled once the fuel was used up in the lines. Replaced fuel filer and filled with that anti gel stuff. Truck sounds like it is almost firing up but still cannot get it to run. When I turn the key on it sound like the fuel pump is working for about one minute and then turns off. Made sure the fuel filter was overfilled with deiseal. Turned it over so many times the lines should be full by now. I used that quick start stuff and it almost starts every time.
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 - Crank But No Start
I have an early 2004 F 250 6.0 that just quit one day and haven't been able to get it started since then. I have tried to follow the No Start checklist...
I have no aftermarket mods or tunes.
I have changed the fuel filters, made sure that there is fuel in the tank and made sure that it is getting fuel.
I have un-plugged the ICP and still no start.
When I turn the key on it goes through the regular sequence and I hear the injectors (sounds like it's doing a buzz test).
When I try to start it, it cranks over, but I hear a good bit of clicking coming from the fuse/relay panel under the driver's side dash.
I have inspected fuses/relay and dont see anything smokingly obvious.
I installed new batteries, but no joy.
While trying to start, it sounds like it may actually do it for a second, and then I get a noise from the starter.
I bought a scanguage and added the PIDs that I found searching through the forum and here are my results.
ICP key on = 0.23 ICP while trying to start = 1.30
ICP Voltage (Volts)
TXD: 07E02216AD
RXF: 0462451606AD
RXD: 3010
[Code] ....
Camshaft & Crankshaft Sync = This is erratic; it will flash 1 and immediately go away. The thing is, I don't know which sensor should be replaced.
Ford 6.0L Power Stroke Diesel :: 2006 F250 - No Crank No Start
I have a 2006 F250 6.0 with 218xxx on it. Have had a ton of issues since day one, but I finally thought I had gotten a handle on all of them until the other day. Truck started sounding a little rough, no noticeable effect on performance, no codes on my Edge CTS (except one random CKP sensor code that went away). Was leaving work later that day to go home and it started up fine.
Got about a 1/4 mile from the shop and went to turn onto a busier road so I put into the pedal a little bit. Truck immediately lost power. Sounded like a turbo boot blowing and I had very little throttle response. Immediately pulled over and checked codes with truck still on, nothing. Got out and popped the hood with the truck still idling to check for CAC tube/boot etc. As I was looking at it, the engine started screeching. I shut it off as quick as I could get back to the cab.
Looked over everything, nothing noticeably wrong. Went to crank it to see what it would do. All i got was a noise from the starter engaging. Belt not turning over. Tried unplugging the fan clutch (read a thread with similar symptoms and that was the issue for them), connected the starter solenoid directly to battery, same issue. Removed belt and attempted to crank. Same thing. Removed all glow plugs to check for hydrolock. Motor slowly would turn with belt still removed and no glowplugs. Removed starter and tested outside of vehicle, solenoid and motor both seem to be ok.
Ford 6.0L Power Stroke Diesel :: 2006 F250 Crank But Won't Start
I have a 06 6.0 f-250 it cranks but won't start untill I pull the secondary fuel filter cap off and seems to vent air in the system out then it starts right up. I can't figure out where it's sucking air. Here's my question I changed the fuel sending unit in the tank a few weeks ago and had a hard time seating the lid on top of fuel tank. If it is not completely seated will this cause air in the fuel system and give me the headache I've been dealing with?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 Sputtering / Crank No Start
2005 Ford F250 6.0 Diesel (bought new). Never had a problem with the engine until about a month ago. Engine has 220,000 miles on it. Oil and filters changed regularly. Ran low (not out) of fuel, started sputtering badly but not killing. Filled up with diesel. Ran better, managed to get home. The next day it was dead. Crank but no start. Since then I have done the following (not in order):
- Changed EGR
- Changed ICP
- Changed IPR
- Changed the STC fitting
- Changed all seals in the HPOP
- Changed glow plugs and harnesses
- Tested each fuse and relay
- Installed new batteries
- FICM tested 48V
- Changed motor oil and filter
- Changed both fuel filters
- Checked for water in the fuel
- Purged air from fuel line
- Replaced dummy plugs
- No codes
- Prayed the rosary
One month later, still crank no start. Thinking about using it as target practice with the AR-15.
Ford 6.0L Power Stroke Diesel :: 2007 F250 - Intermittent Crank / No Start
I have a 2007 f250 6.0 powerstroke that had an intermittent crank no start problem so I replaced the sti valve on the hpop. Put it back together no start ran a few tests found the FICM had 22 volts replaced that still no start replaced IPR valve because I got a 0 ohm reading from it still no start. I am just about out of patience with it I am going to add some pics of the scanner I am using. I dont know the difference between ICP DSD and ICP PRESS.
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 Crank But No Start - Low Pressure?
2005 F250 To date this has been done, some at different times. ARP studs, OEM head gaskets, heads machined, oil cooler replaced, new fuel injectors, reman'd HPOP w/IPR with STC fitting, EGR delete, 4" turbo back and SCT x3 tow tune.
We originally had a leaking injector that gave us issues (Thread is here) but we pulled the cab and went through the motor, installed studs etcetera.
After the rebuild we ran it approximately 1K miles and it ran great, then one day towing a '65 C10 on a 20' flatbed it shut off while cruising down the road, crank no start on the side of the road, scanguage showed ICP was too low to fire the injectors so we towed it back to the shop and replaced the HPOP, still low ICP.
What's the next step of diagnosis? I'll have ICP numbers by Monday, it's been several months since all this happened and I'm currently out of state trying to diagnose. If i remember correctly the ICP numbers were low teens or 20's. I don't know for sure but I don't think we replace the standpipe or dummy plugs when we had it apart, could that be the issue?
My thoughts are either we have a leak in the high-pressure side or low pressure isn't supplying enough oil to build pressure, so in theory, we would want to check low pressure first, correct?
Ford 6.7L Power Stroke Diesel :: 2011 F250 Crank But No Start / Reducing Engine Power
My 2011 6.7L F250 Superduty died on interstate the other night. Picking up throttle pulling onto interstate when a message came on the dash "reducing engine power" and the truck died. It will crank but will not start. It will start on ether but dies when that runs out. Has the following codes... p1249 Wastegate control valve, p0087 fuel rail/system pressure too low, p1291 & p1292 injector high side short to ground or battery (bank 1 & 2), p2291 injector control pressure too low-engine cranking. The codes are telling me I don't have enough fuel pressure but scan tool says I have 4000 w/ key on and 6370 while cranking and I thought 5000 was the pressure needed.
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Keeps Dying And Have To Crank For About 15 Seconds To Start Again
Alright, my 1999 7.3 keeps dying on me in the morning. About two weeks ago I noticed it started to have a weaker start up, even though it has two brand new batteries. Once it starts up, I get around the block and it dies there every time. Then I have to crank it for about 15 seconds for it to start again.
The crank gets faster and faster until it finally start, and the engine is very choppy, like its starving for fuel. After about ten seconds of that it return back to a smooth idle. I then take off, and about 50 yards later it does the same thing. After it does it the second time, the truck runs just fine for the rest of the day with no problems.
I have noticed that when if I turn the truck on and let it idle for 10 minutes first in the morning, it won't die on me. I replaced the camshaft position sensor thinking it was that, but it wasn't.
Ford 7.3L Power Stroke (1999-2003) :: Block Heater Plugged / Truck Crank But Won't Start - Fix?
When the block is cold my truck will not start. If i keep the block heater plugged in it will crank but is still a long start. I have tried just about everything i can think of and it is way too much to list so i will give as much info as i can.
New- gpr, glow plugs, HPOP, batteries, starter, fuses, valve cover harness/ injector and glow plug wiring, vacuum lines. I have checked out just about everything remotely possible.
Ford 6.0L Power Stroke Diesel :: 2003 - Crank But Won't Start
I was driving down the road and suddenly lost tons of acceleration power had to almost flour it to move at all so I pulled off the road to stop and check it out. After I stopped I couldn't get it to start again it would crank like it wanted to start but nothing. So I had I towed home and it sat for a little while and then I tried to crank again, and it started and idled like crap and when I pushed down on the gas pedal there was no reaction, rpms didn't go up or nothing but still would idle like crap.
Symptoms stayed the same for about a day and no I have a crank no start. So then I did what little I could do just to see if it was an easy fix I changed the ICP sensor, IPR sensor, and EGR valve needed to be replaced so I replaced that too. Headstuds and gaskets have been done as well by previous owner but not I think it might be an HPOP problem? I am unable to read codes at the moment as well just FYI. Could this be a fuel filter issue even tho the secondary housing fills with diesel?
Ford 6.0L Power Stroke Diesel :: 2003 F250 Truck Just Died While Driving
I am working on an 2003 F-250 6.0l. The truck just died while driving. No restart. Plugged in my scan tool and I am not getting any High pressure oil. Is there anything other than the Hpop I should be looking at. I know it is a big job to replace the hpop so I don't want to overlook something simple.
View 14 Replies