Ford 6.0L Power Stroke Diesel :: 2003 F250 - A/C Compressor Intermittent Working
I have a 2003 f250 6.0. Recently, I have noticed that my air conditioner will work at first but once the compressor cycles off it does not come back on. I end up having to turn the a/c controls to off and wait about 5 min then turn them back on and it will work for a about 5 min then blow warm air again.
This happens more when towing rather than just driving around. I have changed out the sensor on the canister but it was no dice. The system is charged to the correct level according to my gauge. This occurs more often on hotter days than any.
While the truck has been running and the system is malfunctioning, I have crawled under the truck and noticed the center wheel of the compressor is not turning but can be turned by hand. Do I need a new compressor or am I missing something else that would be simpler?
Ford 6.0L Power Stroke Diesel :: Intermittent Bucking / Hesitation Up Hills - No EGR
When I am on the highway, my 2005 Excursion (6.0) will hesitate/sputter/buck intermittently, usually between 70-80mph/ 1800-2200 RPM, but especially triggered by hills and inclines. Each sputtering episode usually lasts about 5-10 seconds and then will go away for minutes at a time. Does not sputter upon take off or initial acceleration. There is no smoke of any kind. Just got it out of the shop where the mechanic replaced ALL 8 injectors and the fuel pump, as well as flushed the fuel lines, and new fuel filters, and oil change (2 injectors were bad, but there was metal in the fuel filters, so to be safe I replaced all of them - ALL OEM PARTS for everything, including filters).
The week before, I had the IPR valve replaced. Also, recently had the back pressure sensor replaced and the EGR was deleted - and turbo cleaned when the EGR was deleted last month. I also tried unplugging the ICP sensor to make sure that wasn't the issue. Dropped $6k into this thing in the past month and about to lose my mind (and wallet). All research points to either clogged EGR or bad fuel injectors, but both have been addressed, so I am not sure where to look next. No current codes showing up. No signs of leaking oil.
Ford 6.0L Power Stroke Diesel :: Intermittent Hesitation After Stopping At Light / Stop-sign
Trying to troubleshoot a very intermittent (has happened on two different occasions during the last 1,000 miles) hesitation from a stop-light. I've been recording engine parameters (Torque application) on both instances as these have been during longer trips after a period of highway driving. 2004 Excursion, 112K miles.
This feels kind of like severe turbo hesitation (4 to 10 seconds trying to start out before it kicks in) but I don't think that's it. The turbo is a new PowerMax turbo replaced 5 months ago. VGT readings seem pretty normal. The EGR valve is new -- the first instance was with the old and the second was with the new. I've also recently replaced the EGR and Oil coolers (before this).
Here's what's interesting in the captured data though... Normally when I coast into a stop-light the indicated engine load stabilizes at about 40-50% and VGT moves to about 65% to 70% at idle. The two different times this happened (actually multiple times at stop-signs/light close to each other over 5 minutes or so for both of these), when I have coasted to the stop, the engine load increases from low values during coast-down (0% during freeway coast-down or 19-30% during other coast) up to 99.6% (or other similar high values) at idle and VGT seems to be full closed at 85%.
There is absolutely no response to the throttle in this situation for 5-10 seconds. I've either been goosing the throttle a bit or putting it neutral and revving it up first to get things going again. When it finally catches and starts accelerating with power, indicated engine load drops to 50-60% again and VGT opens up to 40-60% or so. None of the other parameters I've been capturing seem to read strangely during this that I recognize. No issues observed during cruise and power seems good. No pending DTCs or engine light.
Here's what the data points I'm capturing (once each second):
Boost
Calibration Input Volts
ECT
EOT
Fan RPM
FICM main volts
Fuel Injector pulse width
ICP
ICP Volts
IPR Duty cycle
RPM
Engine Load
MAP
Trans Temp
VGT Duty Cycle
EBP
EGR Commanded
EGR Error
Added today but not captured during these issues yet:
IAT
IAT2
Baro
Accel Pedal Position
Mass Airflow Rate
Mass Fuel Desired
Ford 7.3L Power Stroke (1999-2003) :: Hesitation When Accelerate Especially Starting From A Stop
I have hesitation as I accelerate especially starting from a stop. It will continue until cruising speed. Funny thing is when I put the cruse control on the hesitation stops and it runs fine. If I want to accelerate while on cruse the hesitation starts again until I let off the accelerator. Is it the TPS ? I changed it two months ago.
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 - No Power And Will Not Accelerate
I have a 2004 F-250 with a 6.0 and am having a serious issue. The truck has about 240,000 miles and has been great until now. About a week ago the truck was running great and had plenty of power. I decided to wash it with my pressure washer (did not spray under the hood, however I did spray in the front wheel wells and underneath the truck). About 5 minutes after washing the truck, I took it out for a drive and noticed when I really got on the accelerator the truck would not want to try harder and motor got very quiet. Really all you could hear was the turbo whistling. Over this past week the problem has gradually gotten worse... a few days ago I had to feather the pedal in order to go up hills. If I gave it more than about 1/4 inch of accelerator, the motor once again would get quiet and the truck would start to slow down and would not want to work.
However, if I let up and only gave it a small amount of accelerator, the motor would sound normal again and it would pull up the hill. Today, I can do nothing more than idle back and forth in the driveway because the motor gets quiet and the turbo winds up if you give it even the slightest amount of accelerator. I have no idea if it's a coincidence that this happened after washing the truck, or if maybe there was a sensor that was rotted and about to die and I finished the job with the pressure washer. I already replaced the egr valve and have been running tons of Howes diesel conditioner and anti gel through it. The injectors were replaced about 50,000 miles ago so I'd hate to think it was them. The truck doesn't smoke at all either.
Ford 6.0L Power Stroke Diesel :: 2004 F250 - Sneeze Like Hesitation Just Before Downshifts To Passing Gear
I have a 04, f-250, with a 6.0 liter engine. I have had the Cat removed and in the last couple months it has developed a sneeze like hesitation just before it down shifts to Passing gear, If I push my foot into the fuel it jumps right down thru the sneezing into passing gear. I have changed fuel filter and grade A cleaned my EGR valve. the only Codes it throws is P0403 and P0405.
View 10 RepliesFord 6.7L Power Stroke Diesel :: 2011 F250 - Intermittent CEL For P2074?
I'm starting to get an intermittent CEL for P2074 ("Manifold Absolute Pressure/Mass Air Flow - Throttle Position Correlation at Higher Load"). It first came on Saturday halfway into a 4 hour drive (Not towing, just driving 75mph-80mph on the freeway). I cleared the code and restarted the truck and it immediately came back on. About a half hour later I stopped for fuel, cleared the code, and it stayed off for the rest of the trip.
Got into the truck today and drove it for 10 minutes (driving around town) and it came back on. Cleared the code and restarted the truck, drove it for about a hour and it never came back on. The truck is running and driving just fine.
The truck is a 2011 F-250, all stock (except for a AFE Cold air intake that's been on the truck for a while now). The truck has about 98,000 miles.
From what I've read on other posts, it might just be a mass air flow sensor? Should I just replace that myself, or pay the $100 extended warranty deductible and take it into Ford?
Ford 6.0L Power Stroke Diesel :: 2004 F250 Just Died All Of A Sudden - Intermittent Power Loss
Ok I have an early 2004 F250. Recently changed out the #8 injector and then had to replace the ICP Sensor. Was running great then while driving down the road just died all of a sudden. Would start right back up with no issues. Continue driving and I am getting intermittent power loss. Also noticed that when it would lose power suddenly the glow plug light would come on.
Codes are P0102, P0113, P0272, and P1000.
P0102 Mass or Volume flow circuit low input
P0113 Intake Temp circuit High input
These are just soft codes not setting a light off. MAF is plugged in and I will check wiring here later after work but could this be causing my intermittent issues?
Ford 6.0L Power Stroke Diesel :: 2007 F250 - Intermittent Crank / No Start
I have a 2007 f250 6.0 powerstroke that had an intermittent crank no start problem so I replaced the sti valve on the hpop. Put it back together no start ran a few tests found the FICM had 22 volts replaced that still no start replaced IPR valve because I got a 0 ohm reading from it still no start. I am just about out of patience with it I am going to add some pics of the scanner I am using. I dont know the difference between ICP DSD and ICP PRESS.
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - Lack Of Power / Truck Will Barely Move And Takes Long Time To Accelerate Under A Load
I have a 2006 F250 6.0 Amarillo Edition. 133,000 When I bought the truck it was a theft recovery vehicle where the turbo, injectors, FICM and wiring harness were stolen. The company I bought it from replaced the injectors, wiring harness-new, and a used FICM, and turbo. Also has EGR delete and SCT tuner with basic tunes. I believe the SCT was put on to mask another problem. No dealer would spend that kind of money to sell a truck unless something was wrong. The truck would accelerate some with the tuner but shift the tires so hard it would bark them. I removed the tuner and went back to stock program.
The truck will barely move and takes a long time to accelerate under a load. In park and neutral it is fine. A friend has a ford diagnostic program on his computer and says the readings were all good except EBP was a little high. Removed exhaust and air intake to verify no restrictions. Turbo sounded like the vanes might be sticking so I replaced the turbo and VGT solenoid. Now truck feels like its trying to make more boost but not transferring power to the engine. Have blown the silicone hose off twice now during testing. Checked the EBP sensor and tube and only thing I see is a little carbon buildup inside the sensor. What else to check. I'm new when it comes to diesels.
Ford 6.0L Power Stroke Diesel :: 2004 F250 - Intermittent Heavy White Smoke
Yesterday I was coming back from town and as I was looking in p/s mirror changing lanes I noticed heavy white smoke. I only noticed this upon decel or coast. Once I rolled back into the throttle the white smoke would dimminish. I'm sure it was coolant from the smell. The truck (04 F250 CC 6.0) is now at the dealer for troubleshooting. I believe it to be a blown head gasket, but wouldn't that make it blow white smoke out the exhaust all the time? Maybe a cracked EGR cooler?
View 11 RepliesFord 6.0L Power Stroke Diesel :: 2007 F250 - Check Engine Code - ICP Circuit Intermittent
I have a 2007 f250 and got a check engine code icp circuit intermittent and to what I know icp sensor should be on the valve cover on the passenger side but it's not I bought the truck few months ago could it be that they swapped the engine for an early 6.0 or is there any other place for the icp sensor???
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 - Intermittent No Start / Idle About 15 Minutes And Died
Started my 2005 f250 powerstroke, idle about 15 min and died like I turned key off. Hooked up scan guage had no flp, fmp or syc ipr and icp was good. Checked ficm relay and fuses and all checked good. Next morning went out and it started flp, fmp, sycall good. Idled about 1 hr and died again same bad readings. Messed with relays and wiring to ficm, it started and died after 2 min. No start again, next morning still no flp, fmp. Went out again in afternoon and everything was good again, I did nothing to it from am to pm, was loading my pistol they shoot horses don't they. I have new batterys, I changed the ficm power card last summer for low fmp. When it is running everything looks and sounds good no miss.
View 14 RepliesFord 6.7L Power Stroke Diesel :: 2012 F250 - Intermittent Thrumming Noise At Highway Speed
2012 F250. 15k miles. It's intermittent, speed related, some sort of resonance or harmonic. WoooOOMMmm....woooOoMm, maybe every two seconds at 70 mph. Worn out tires once made a similar sound on a car I owned. This was severe inner wear on the rears. I'm not sure whether it's new or something I just never noticed; it's subtle.
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 Error Codes - Injector Control Pressure Sensor Circuit Intermittent
I bought my truck 2 month ago. I use it for commuting, only short trips now ( 10 min ). After about 2 weeks the Check Engine light came on. The truck is running fine, no problems I believe, starts easy. After another 2 weeks, the CEL disappeared. Another week, and the CEL came back on and it`s there since. I have a code reader, these are the codes and meanings according the manual:
P0299 - Turbocharger "A" underboost condition
P2286 - Injector control pressure sensor circuit high
P2287 - Injector control pressure sensor circuit intermittent
P0299 Pending - same as first but with "pending" status
This is my first diesel and my first turbo charged engine. Is this a common problem? How serious? It`s a bit strange that the error came up before but disappeared. Can that happen just because of the short trips I`m making? I`m planning a long trip soon with towing my trailer, so I want to make sure the truck will not break down during the ride.
Ford 6.0L Power Stroke Diesel :: 2003 F350 - Intermittent Long Crank When Hot
2003 6.0 will fire within 2 seconds when cold, literally a "bump the key" and she fires up scenario. Recently and only when the engine is hot I'm getting extended crank times and sometimes it takes several attempts for the truck to start. I replaced the HPOP with an upgraded pump after the factory HPOP went out at 311,000 miles. I know this sounds like a standpipe leak scenario but it doesn't act up all the time, sometimes it fires right up even when its hot. my thinking is a leak is a leak and only gets worse.
My IPR is reading in the 26% range, FICM is steady in the 47.5 to 48 volt range and at idle 585 to 600 psi on the ICP with a good FICM sync. I'm going to to use my scan gauge and see if I can catch an extended crank scenario to see if the ICP is reaching 500 psi but is there somewhere else I should be looking? FICM relays possibly? I've noticed when i turn the key on I'll hear the fuel pump,vacuum pump but the clicking sound is very brief or nonexistent (not sure what the clicking noise is from I assumed glow plugs but its absence is noticed)...
Ford 6.0L Power Stroke Diesel :: 2003 F350 - Intermittent Battery Light On / Off
I have a 2003 F 350 Crewcab 6.0 liter SD. I was preparing my truck for the first haul of the Summer. I noticed that my batteries were on their way out after 2 years old. I replaced them and noticed I had an intermittent battery light coming on/off on/off. It seemed like only at lower RPMs. So the day of my trip, I ended up changing out the alternator.
The trip went fine, however, I noticed that pesky battery light came on and then off a few times. I also got a hot plastic type smell from the front of my truck.....you know that hot plastic smell Anyway, I got home just fine. Via Torque Pro, my battery volts were reading 12.2ish when my battery light came on, but then would quickly return to 13.9.
Since I"ve been home, I have read about fixing the grounding points for our trucks and also adding a second ground wire and a second hot wire from battery to battery. I can not find exactly where the ground's lead to. I still have that fricking battery light coming on .....more often that not. How to chase this problem.
First I need to find out where the ground wires go to. My volts of recent have been reading 11.5-12ish when the truck is running and the friggin battery light is on. I did search and found a few links to this problem, but where to find the grounding points.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 - Intermittent Starter / Whirring Sound When Crank
I have a 2001 f250 ext cab long bed 4x4 that I use as a feed pickup. I have had it for about a year now. one of the issues I have noticed since I bought it is the issue I am having with the flywheel/starter. Its very random like maybe I have a missing tooth or something on my fly wheel. but every so often when I would go to crank my truck over it would just make a little whirring sound and nothing happen ( like my starter gear isn't sliding out and engaging my fly wheel.
After looking through my inspection cover I noticed I had a little wear on the sides but no teeth to my knowledge broken or stripped off. I noticed my starter had one bold loose but other two perfectly tight. It was also covered in oil and dirt from my truck sweating horse power I decided to replace my starter and have my original ford starter rebuilt. I replaced it with a NEW oreillys starter. I noticed it cranked about 5 times as fast but again every 10-15 starts I am getting the same no start. any thing I am over looking?????
Ford 6.0L Power Stroke Diesel :: 2003 F250 - No Start After EGR Delete
Just did an egr delete, oil cooler, icp sensor and exhaust on an 03 f250 6.0l. got it all back together and it cranked up and ran for about 30 seconds then stumbled and died. read to pull out the ipr sensor and check it and it had a piece of debris on it covering the screen. took of the debris and still no start.
View 6 Replies