Ford 7.3L Power Stroke (1999-2003) :: Slower Cranking Time And Took A Second Or 2 Longer Than Normal
I have a 2002 F350 7.3 with 76,000 miles (still a baby) ... about a week or 2 ago i got in my truck and went to start it like normal, except instead of whipping over and firing right up in the snap of a finger, it kinda had a slower cranking time and took a second or 2 longer than normal. My first thought was maybe the battery's, BUT there basically brand new !!! not even a year old !!! ... so i figured maybe a starter, but i just left it as is, it still ran normal after firing.... Until this morning, I went to go start it and it cranked over 3 or 4 times real slow and would crank any more, it did this to me multiple times. Its acting like dead batteries so i put a jump pack on it, no change. I am thinking maybe a starter ....
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 - Misfire When Cold / Lost Oil And Long Cranking
I've got a99 F2 50 super duty with a 2000 2001 motor. I got the truck in the beginning of last winter so this is my first summer with it.
When I first got the truck there are injector issues with the truck. Since I fix the issues there has been little problems out of the truck however it's still suffered misfires when Cold but once up to operating temperature it was fine. Yesterday I had to go with a friend before leaving for the trip I checked the oil it was full and appeared normal the trip was about 150 miles. I came home park the truck after everything was done. This morning I came out started the truck everything acted as it should... truck fired right up everything was great went and dropped off my trailer at the yard come back got fuel when I come back out from paying for the fuel the truck took about 30 seconds to fire up I checked my gauges and torque pro and everything seemed normal. So on my way I went.
I drove about 10 miles on the highway to the place I had to be when I got done doing my business I came back out to start my truck and it did the same thing this time however it took longer to start I managed to drive about a mile down the road when I noticed my old pressure gauge flickering and my Oil pressure light on I immediately shut it down and coasted into O'Reilly's parking lot I check the oil in the truck and it was empty according to the stick I added two whole gallon.... With it filled back up down the road I went. So currently the truck is still suffering from a long hard starts it takes 30 to 45 seconds before it all actually fire up once it fires up everything appears to be fine however the truck is slowly smoking a bluish black color... It's never done this before however I've never had this truck in the middle of summer when it's real hot out I don't think this is normal.
The truck doesn't appear to be down on any power actually it, acts as if it might've picked up of some power it is felt real peppy today compared to other days. Also I might note that about a week or two ago I started smelling diesel like either really rich diesel or raw diesel wasn't too bad but I just got whiffs of it for now and then. Now there is a burn oil smell present from the exhaust. Like I was saying earlier when I first got the truck I had to service the injector O-rings... I was told that the miss firing when cold was caused by the Poppitz sticking. The misfire hasn't been present since it got a little warm outside like I was saying it was only when the vehicle is cold.... Just thought I would mention the injector issue not sure if it's relative or not..... My thoughts are it's back to an injector issue or O-rings or possibly did I wipe the motor when it ran out of oil. I am not aware of where the oil went as there is been no leaks or drips.
Ford 7.3L Power Stroke (1999-2003) :: No Start - IPR Goes Straight To 98.6% While Cranking
This morning I went to start her up, and she fired right up and I let her warm up until oil temp got to 100F, when I realized that I wasn't leaving right away so I shut it down and came back about an hour later. Oil temp now at 78F, but she wouldn't start. Have Torque Pro running, and the IPR is going straight to 98.6% every time while cranking, sits at 14.7% with KOEO.
Truck's been running fine, recent oil/filter change (T6 10-40W), cleaned & re-installed CAC tubes/boots for leaks. All else seems good. Pulling the ICP sensor shows HPOP going to 2800psi, with IPR @ 30%, still no start and not even a cough.
The IPR is original, rebuilt once several years ago.
Ford 7.3L Power Stroke (1999-2003) :: Died And Won't Start / RPMs Only Like 200 When Cranking
Was driving to work about 4 miles into my travel rolled around corned and she died..... tow bill and cps she fired rite up. Ran at idle in drive way because I was a little leary for about an hour left drive way went 2 miles went to pull in to store died again. Another tow bill and 2 more cps still won't start rpm is only like 200 when cranking but sounds like a lot more. The wts light works, batteries are pretty new, cps in new...
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 Struggles To Start When Crank First Time
I am trying to diagnose an issue with my 2003 F-250 6.0L PSD.
The first time I crank it everyday, it struggles to start. Beyond that, it seems to run fine and not have issues cranking throughout the day.
I've recently replaced both batteries, the FICM, the fuel filters and the FI wiring harness. What could be the issue?
The video shows exactly what I deal with every morning.
YouTube - 2003 F-250 Cold Start Issue ....
Ford 7.3L Power Stroke (1999-2003) :: Truck Harder To Start After Long Cranking
Background on the vehicle, Last week installed Swamps 200cc/30% injectors with a 38r. Had swamps reburn my chip for the new upgrades.
But heres the problem i noticed starting the truck was a little harder ( longer cranking ) till it would start never thought of anything since i read air gets in and can cause it but then yesterday and today its taken 30 minutes to start the truck since i have to do a trial and error.
The truck just seems like the batteries are being drained or something along those lines. i also noticed my gauges keep resetting back to blue( default color). Today I plugged a battery charger up all good voltage i charged them so both read 14v and still no start. So a couple of attempts at starting with chip in and ICP on nothing
I unhook the chip and ICP get a half start then eventually it starts. After then i can hook it all back up and it starts good for the rest of the day but for what ever reason after it sits all night it doesn't want to start up right away. I'd like to figure it out today since id rather not wake up at 4am and attempt to do this all before work each day.
I noticed that my gauges would reset to the default color after each turn off. So i unscrewed my ECU and then redid that to make sure its tight. along with making sure the chip is seated properly. after that it stopped resting my gauges. Whether that's the issue or not i cant say but ive been checking my HPOP oil level since i stopped driving it around 1400. and hasn't changed oil levels are good. I plan on starting it before I go to bed around 2200-2300 just to check and see what happens.
Ford 7.3L Power Stroke (1999-2003) :: Hard To Start / Whitish Smoke When Cranking
This is kind of strange, I have a hard start problem, when I crank it the first time, it fires immediately, kind of like a romp, but doesn't start, then when I crank again I get a lot of whitish smoke and no start. I read to try and unplug the ICP and try it. That worked, and I had oil in the connector. I replaced the ICP, but have the same problem. I still have to unplug the ICP for the truck to start. When it does start, it runs great! No injector stiction, no smoke, no rough idle, it runs and sounds great. Why unplugging the ICP is still required to start? (Only after sitting for more than 10-12 hours).
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Hard / No Start Situation Cranking Drains Battery
I've been working through with hard starting on my 2002 7.3 A while back I took my batteries to Autozone and had them check them. They said they were fine but because of my hard/no start situation cranking on it for a short time (couple of minutes) kills the battery. The transmission shop said that they had to charge it after sitting for a couple of days to get it started. I have a multi-meter and know how to check the voltage. I even have AE and it gives me the voltage. Are there any other tools or procedures to check the health of the batteries?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: E99 Won't Start - White Smoke / RPMs Move While Cranking
Fine one day, no start the next. Been skimming over the 7.3 no start thread, so w got some ammo for him to check. White smoke while cranking, rpms move while cranking. Nothing to read codes or other sensors YET. Tried the unplug ICP and it "wanted" to fire. So, I have him my spare IPR to try. I'm sure he checked the fuses but will confirm via text...
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F350 - Hard To Start / Taking Lot Of Cranking
I have a 2001 F-350 7.3L Powerstroke. 48,000 miles. I've been having trouble with cold starts. So far it has always started but is taking a lot of cranking, but it hasn't gotten too cold yet so I'm worried about when it does. I ohmed out the the glow plugs and am getting close to 0 resistance. The GPR has 12.5 volts on the hot side and when the relay is closed 10.5 on the other side. Is that difference in voltage in the GPR enough to screw up the Glow Plugs heating up? If I plug it in at night it starts right up. I'm worried about when I am at work for 16 hours and don't have a place to plug it in this winter. BTW this is my first winter with the truck.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Won't Start - Battery Voltage Will Keep Falling If Cranking Continues
So when its cold and im talking below 55 degrees, and the truck hadn't been started that day, it will turn over 3 or 4 times before the voltmeter takes a dive down to 10 volts or so and doesn't start. The voltage will keep falling if cranking continues. I took the batteries out and had them tested. They are both above the rated cca. So im thinking it could be the starter windings?
I did replace an injector recently so all the cranking to get it going again may have ruined the starter? But when I hook up the battery charger and jump the truck it starts. And after it has been started it will continue to start easily the rest of the day.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F550 Taking 4 Seconds Of Cranking To Start Consistently Hot Or Cold
I have now replaced hpop, injectors, cups, gpr, batteries, uvch on both sides, icp and ipr on my 2002 F550 and it still has a long crank to start.
It has been driven about 1,000 miles since then and no change. I have no codes except buzz test produced a high to low 1272 1274 1276 1278 one time. Cannot get that to happen again.
It is taking 4 seconds of cranking to start consistently hot or cold. It always starts but cranks for what seems like too long compared to my other 7.3s. I have included a screenshot of the data and am curious on what everyone's thoughts are as I am out of things to look at!
Ford 6.0L Power Stroke Diesel :: 2006 F250 Won't Start / No Cranking
I have a 2006 f250 superduty 6.0. The truck ran fine a week ago and than died as I was going to take it for a drive. I figured out that the fuel pump (air dog system) was not working. I fixed that and primed the pump. The truck still won't start. When it first happened the truck would crank but not start. Now all I hear is the starter but no cranking. Both filters could be replaced. The bowl to the upper is dry when I take the cap off. However fills up when you turn the key on. I'm not sure what else to try and I need to get this truck started.
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 Keeps Cranking And Not Turning Over
I have a 03 f250 6.0 . I rebuilt the whole top end. When i finished it 15 months later due to personal issues I started it. It ran for about 4 hours i turned it off the next day i went to start it again and didn't kick over so i figured it was batteries they might of died (it was about 3 degrees out) so i went to get new batteries put them in and it started using diesel 911 and starter fluided i let it run for awhile. I went back the next day to start it and it did t turn over it just kept cranking and started to die out so i stopped trying. Now a week later I am at it again. Could it be not starting because of bad fuel trying to get through the system or could it be something else?
View 3 RepliesFord - F250 :: 2003 - Refuses To Start At Random
On Saturday afternoon of Labor Day weekend my dad's 2003 Ford F250 "died" in the parking lot at my work. It had been running fine all morning, but then I stopped by work, and when I went to leave it barely started, ran for a few seconds at a rough idle (presumably on whatever fuel was already in the system), then died and would not restart. Turned over strongly (new battery a few months ago) but no ignition. Checked the fuses and fuel pump interrupt switch, but everything was fine. Had just put 15 gallons of gas in earlier in the week so I "knew" that wasn't the problem.
When I had it towed to my mechanic. He didn't get a chance to look at it until the weekend, and called me Monday to say that it started just fine for him all weekend, but it could use some gas. I knew I should still have 12-15 gallons in there, so we came to the conclusion that someone had siphoned my gas. Monday night I picked it up, feeling dumb for not checking that more carefully, and drove to the gas station. Sure enough, the gauge registered "E" and the low fuel light was illuminated. Put in 8 gallons. Started the truck and the gauge popped up to 3/4 tank.
8 gallons is NOT 3/4 of a 32 gallon tank. It's 1/4. The original fuel was still in there! On the way home from the gas station I stopped by work to load up the lumber I had to leave there the first time it died and--you guessed it--died like before. This time the gauge definitely read 3/4 tank with the key on, so the problem was not low fuel. I didn't want to pay to have it towed again, so my mechanic said he'd come look at it when he got time. I tried to start it a few times throughout the week and on Saturday it started right up and ran strong all the way to his shop, where it continued to start every time we tried it. It could be the crank position sensor, but the confusing part is the low fuel indication.
Could the fuel gauge have gotten stuck when the truck was was pulled up on the rollback? And would it have stayed like that all the way to the gas station? I also don't think it's the fuel pump because it runs so strongly when it does start. The second time it died the gauge still read 3/4 tank so I don't think it's related. The mechanic can't fix a problem he can't reproduce, and I really need the truck to pull my 3,000lb landscape trailer on the weekends. My 2000 Wrangler isn't exactly ideal for the job! Oh yeah, the truck is stock, 5.4L gas, off-road package, tow package, extended cab, long box, auto trans, 85K miles.
Ford 7.3L Power Stroke (1999-2003) :: Hard Time To Start Intermittently
Just got myself a gently used Econoline E-350 7.3 Diesel and was loving it when she ran:
E-350 7.3 Diesel
Recently I have been having some charging issues. It started with it intermittently having a hard time to start, especially when it was warm. I carried a jump box with me and that always seemed to work. Then I noticed the voltmeter on the dash dropping. It went down to the 8 and I was like something is wrong.
Checked the battery voltage, it was at 9.6v. OK, maybe alternator isn't charging. Advance Auto tested the alternator, said it was bad. I replaced alternator. No difference. I pulled the battery and ran it on a conditioner to bring it up to proper voltage. It's now at 12.6v resting. Starts the van no problem. When running though the voltage doesn't increase to 13-14 volts like it should though telling me the alternator isn't doing it's job. Increasing engine RPM actually decreases voltage? Checked all the obvious things like bad grounds but everything seemed clean.
The only thing that was fishy was when I pulled the three way plug from the alternator, one of the pins had corrosion on it. I cleaned it up before installing the new alternator. I didn't do a diode test on the new alternator because I figured it was new, but hey maybe I got a lemon?
Anyway I'm going crazy trying to figure out where the problem is. All fuses are ok. Is there an external regulator or something I should be on the lookout for? Is there anything else that could be causing a non charging issue? The battery was manufactured in 2014 so it's relatively new.
And on a random note my ABS light is now on?
Ford Super Duty (1999-2016) :: 2003 F250 - Key On But Not Cranking / No Start
I have a 2003 F250 with 157,000 mile. Left the house last week and got about a mile down the road when I realized I had forgotten something. Pulled off to turn around and had no power to get back onto the road. RPMs wouldn't go over about 1500. Finally got it on the road and it completely shut off. Was able to get it home and have been tinkering with it. Stats from Scangauge are as follows:
Key on not cranking.
IPR 14.81%
FICM 47.6-48.0
Sync=0
ICP 32
Data while cranking.
IPR 43-47%
FICM 38-42
Sync=1
ICP 1532
I'm leaning towards a bad FICM but the ICP pressure seems to be high to me.
Ford 7.3L Power Stroke (1999-2003) :: F250 - Click With No Start
So I bought a Lifted 1999 F250 a couple weeks ago and last night the thing wouldn't start. The battery connections are not perfect but there's power going to the truck because it will give me the wait to start light and all. When I try to start it there's one really loud click and certain lights like the clock momentarily turn off when it clicks. Tried hitting the starter didn't work. Tried putting a jump pack to the starter and it didn't spark like expected.
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 Won't Start When In Park
My truck will not always start when in park, Have to switch it to neut sometime, and sometime after putting it in park it won't fully engage, I know the part that I need to replace just don't know the name or the part number for ford....It is the part that adjusts the shift indicator...
View 2 Replies