Ford - Explorer :: After Neutral Safety Switch Replacement Shift Alignment?
Daughters explorer sport trac, needed a neutral safety switch and a fuse ( no reverse lights),, I have replaced both but now the shifter doesn't line up right.
P is now reverse, and cant get all the way over to 1 with out holding it...
the two marks in the switch line up for neutral.... and switch is keyed to shaft...
how do i now re align this so shift indicator and transmission are on the same page again??
I am guessing move tranny arm all the way to the rear of the truck position and put shifter in P....then put cable back on arm.... but doesn't seem to work ....
Santa FE SM (2001-06) :: Jiggle The Shifter To Get Engine To Crank - Neutral Safety Switch?
I have a '05 santa fe, auto, 2.7L, 4WD...sometimes I have to jiggle the shifter to get the engine to crank...would this be the neutral safety switch? or is there something in the shifter housing that could be causing this?
Maybe a minor adjustment... Just a slight movement of the shifter and it fires right up... If it is the neutral safety switch..where is it located? on the trans?
Ford Wiring/Electrical :: Analog MLPS Neutral Safety Switch Shows Continuity In Neutral But Not In Park
I have a '94 E4OD trans in my '53 F100. It uses an analog MLPS for the gear selection indicator, Neutral Safety Switch, and Backup light.
My MLPS Neutral Safety Switch shows continuity in Neutral, but not in Park, I need to be able to energize the starter solenoid in both Park & Neutral.
Shouldn't the MLPS show continuity in both Park & Neutral?
Accent LC (2000-05) :: Neutral Safety Switch Exact Location
I can't seem to find the location of the neutral safety switch on my 2005 accent 5 speed manual. I removed the air filter box and looked all around the top, bottom, and sides of the tranny. I have the new part so I do know what it looks like.
View 6 RepliesLexus SC430 :: Code P0705 - Neutral Safety Switch Adjustment
I have recurring P0705 trouble codes. Lexus dealer checked the N/S switch itself and said it's good. I checked all the wiring, found an open, shouted Eureka! Ran a new wire, now all wires test good, but still getting the code. SO - I think I may need to adjust the position of the switch, since the trouble code is for a range malfunction. BUT - I can't find a procedure anywhere.
View 3 RepliesFord Super Duty (1999-2016) :: Neutral Safety Switch Removal
How do I remove the neutral safety switch? I bought a replacement and am having trouble removing it.
After shifting into neutral, I disconnected the connector, then unbolted the two screws. Now I can't get the little white ring that connects the lever coming from the transmission to the actual switch. I have tried prying it off with a screwdriver, spraying a little PB Blaster to lubricate it a little. Nothing will get it off it seems.
I'm leaving to go back up to school tomorrow afternoon, and I need to have this fixed before I leave.
Ford Wiring/Electrical :: 1989 - Won't Start Intermittently - How To Replace Neutral Safety Switch
1989 F250, C6
Random starting problems. Starter relay did not fix it.
Ford 7.3L Power Stroke (1999-2003) :: 4r100 Transmission - How To Bypass Neutral Safety Switch
I have the 4r100 transmission how do I bypass the safety switch? Also what are your thoughts on starting the engine with the transmission out? I know to bolt the spacer plate to the engine.
View 7 RepliesSanta FE SM (2001-06) :: Blower Switch Replacement
How to remove center panel in order to replace faulty blower switch?
View 1 RepliesChevrolet - S-10 :: 1995 - Changing Clutch Safety Switch?
I need to replace the safety switch on my 1995 S10 w/ a 5 speed manual tranny. It doesn't seem to want to come out. Looking at the new one, I would guess that it MAYBE fits in sort of like the holes on a wall hanger. You know, sort of a pear shaped hole that a screw or something fits into and slides down to make it stay. Am I right? And if so, how hard is it to get out/replace? I don't really want to destroy the old one, but that is looking more and more like how it's going to happen.
View 17 RepliesToyota - 4runner :: Periodic Non Starting - Park Safety Switch Replaced?
What could be the cause of this? Have replaced the park/neutral safety switch and the Toyota Mechanic found loose wires on the Master Plug-In and repaired the Ignitor Connector. The computer generates no code to identify a problem. Problem still not fixed. I eventually get it to start but do not know why. Fuel pump replaced a couple of years ago.
View 2 RepliesFord Ranger / B-Series :: 1999 - Clutch Safety Starting Switch Going Out
I have a 1999 ford ranger and I believe my Clutch safety starting switch is going out. Some times I push my clutch in and truck starts fine other times it will not turn over so I stomp clutch and then it starts. My question is, is there any way to bypass this switch?
View 5 RepliesCamry :: 2007 SE Cruise Control Switch Replacement
My girlfriend and I were riding in her 2007 Camry SE about a week ago on the highway. She pushed the button on the cruise control switch to turn it on, and the button popped out of the end of the stalk (it did not completely come out, but popped out about an inch). She pushed it back in, but it won't turn the cruise on now.
What all is involved in replacing this switch? I was assuming it was as simple as removing the bottom rear cover on the steering wheel and swapping it out, but I wanted to check beforehand.
Ford Ranger / B-Series :: 1988 - Clutch Safety Switch Wires Melted
I have an 88 ranger 2.9 manual trans. The clutch safety switch wires melted (red with light blue) 2 come off the ignition, I traced the one to the clutch switch and replaced. My problem is my book says the other goes to " electronic shift control module", I can't find this module and I can't seem to chase wire as it gets lost in wire loom.
View 4 RepliesSanta Fe (CM - 2007-12) :: 2008 - Grinding Noise In Park And Neutral
I have a 2008 Hyundai Santa Fe and there is a loud grinding sound when the car is in park and neutral. This noise doesn't happen all the time but i would say 50% of the time. When there is the noise it does go away when i put the car into drive or reverse.
View 16 RepliesSanta Fe (CM - 2007-12) :: Always Start In Neutral / Rarely Starting In Park
UK 2.2 Diesel
Problem for about 3 years. Always starts in neutral, rarely starts in park.
Any possible cause. Maybe a micro switch or a cable adjustment.
Ford Super Duty (1999-2016) :: 2002 F250 - No Clutch Safety Switch
2002, F250, 5.4L, ZF-6 trans.
Ok...today by accident turned the key with the truck in gear and clutch not depressed...much to my surprise the truck tried to start and lurched forward.
Is this a sign of a failing clutch safety switch or Could it be an ignition switch problem? Anything else that I am not thinking of?
Santa Fe (CM - 2007-12) :: 2008 - Whine When Trans Warms Up And Is In Drive Or Reverse / Not In Neutral
The car has about 53k miles. The problem has persisted since probably 20k miles. The whine is only after the trans warms up and is in drive or reverse, not in neutral. Whine is while the car is stationary or moving at low speed. The whine doesn't seem to change due to gear it is in. It does not change frequency with engine RPM. It does seem to diminish the more load the transmission is under.
Whine is probably not an accurate description, it sounds like a noisy pressure relief valve. Had Hyundai service look at it and all they said was all pressures in the transmission are normal. They could not find any cause.
It sounds like a bunch of small ball bearings running in a loop and can hear each one impact. Sharp raspy impact type sound.
You cannot hear it from the interior but it is quite pronounced while in the garage or if you hear the car coming down the driveway.
Santa Fe (CM - 2007-12) :: 2008 - Grinding Noise Coming From Front Of Vehicle When In Neutral
When I start my vehicle, it makes a grinding noise, sounds like it's coming from the front of the vehicle, when I put into gear it stops. It started gradual and is getting worse. It's a 6 cylinder automatic, with 108 k miles.
View 3 Replies