Santa Fe (CM - 2007-12) :: 2008 - Grinding Noise In Park And Neutral

I have a 2008 Hyundai Santa Fe and there is a loud grinding sound when the car is in park and neutral. This noise doesn't happen all the time but i would say 50% of the time. When there is the noise it does go away when i put the car into drive or reverse.

View 16 Replies

Santa FE SM (2001-06) :: Idling Very High When Put In Park Or Neutral

My 2001 Hyundai Santa Fe has recently started idling very high when put in park or neutral. While in drive the engine idles above 1K and you need to keep your foot on the brake to keep from moving forward. If you shut down the vehicle while idling high, the car will not start right away. It needs to cool down for 10 -15 minutes before restarting. It will run fine for awhile but will go back to revving up again.

View 7 Replies

Santa FE SM (2001-06) :: 2004 - High RPM In Park And Neutral

I'm having trouble diagnosing a high RPM in park and neutral on my 2004 Santa FE 4WD 2.7L. Idle's great in drive and reverse. Occasionally when I start the car up it will shoot up to 3000 RPM until I shift into drive or reverse with a heavy thunk. Then it drives fine. When I shift back into park when I'm done driving, it will shoot back up. To avoid this, I just shut the car off in drive and then shift to park.The weird thing is, sometimes it doesn't happen at all. Sometimes it starts right up and shuts down with perfect idle. However, once I give it some throttle in park in these instances, the idle will jump back and forth between 1500 and 2000 and won't die back down to 800 where it should be until I shift into drive or reverse. Not sure what's going on.

I've replaced the idle air control valve, purge valve solenoid, and camshaft position sensor, but to no avail. I also replaced the throttle position sensor a few weeks ago, but that didn't seem to do anything, so I took it back. I'm wondering if I maybe didn't do the correct installation procedure. I still have the old grey TPS for what it's worth. Should I change this? I've also played with the tension in the throttle cable, but I don't really know how to get it exactly within specifications. I definitely removed some slack. I just checked for vacuum leaks using the cigar method with a hose from the PCV valve with the throttle body sealed with saran wrap, but I couldn't find anything. My method was shoddy, and I don't really know what I'm doing, so I wouldn't rule out a vacuum leak by any means.

View 1 Replies

Santa Fe (CM - 2007-12) :: 2009 - Engine Wouldn't Start / Shift Lever Was Stuck In Park

I have a 2009 Santa Fe and last night, out of the blue, the engine wouldn't start. The shift lever was stuck in park and the brake pedal was very stiff and wouldn't move much. I popped the cap off the shift lock and moved it to neutral at which time the car started without a problem. I could drive but shifting was difficult and the lever didn't really click into a gear. I noticed that when shifting gears. the indicator on the dash would change from N to D and to R in reverse but when I moved up to park, the indicator went blank and the lever locked up again and had be released manually. I also noticed when I got home, since my driveway is a slope, that when the car seemed to be in park is rolled down the driveway, so I had to engage the emergency brake.

View 13 Replies

Nissan - Altima :: 2007 - When Shifting Into Park It Won't Shift Down Past Neutral

My automatic 2007 Nissan Altima has developed an intermittent problem when I go to shift it into park it won't shift down past neutral. I can't physically move the gear shift past neutral and can't take my key out of the car. If I wait awhile or drive off somewhere else it will later allow me to shift normally again and won't happen for awhile. It has happened maybe 8-9 times but I worry it will get worse or break the transmission. I've taken it to a mechanic and they looked at the transmission and didn't see a problem but sense they couldn't recreate the issue they couldn't fix it.

View 1 Replies

Santa FE SM (2001-06) :: High RPMs In Park And When Starting

Earlier this week, noticed that my car was surging on its own; basically, if I came to a stop, I could still feel the engine, like it wanted to just take off. And if I would have taken my foot off the pedal, it would have done just that. Also, I knew the car had gas, but sometimes, when starting the car it would not start at all. I would have to wait about 5 minutes or so and add major gas to it with the pedal and then finally it would engage. And then the last thing was that when I would get to my destination and put it in Park, the RPMs would go up to about 1500 or so, maybe a bit higher and then stay there and go back down to about 1000, without me pressing on the gas pedal at all. So anyway, thought it was the throttle position sensor, so I had my Dad install a new one on the car. It was a pretty easy process and thought that took care of the problem.

The surging part basically stopped, so the new TPS took care of that, but then it still had problems with starting. Took it to a car repair place the next day and they changed out the spark plugs, said that they were causing a misfire in the engine. Also changed ignition wires and a new gasket. So after they were done, drove away and all seemed to be fine, but then went to the dentist and Parked and then the RPMs went up again. Tried to start it immediately afterwards and it wouldn't start again. Tried a few minutes later, added gas with the pedal and it did start. Took it back to the car repair place, they drove it around, inspected everything and everything checked out fine. (Yeah, of course!) Ok, so just thought maybe the repairs were taking a bit to take effect. But later in the day, wouldn't start again.

So next morning, took it to the Hyundai dealer. They looked at everything for about 2 hrs, and said that there was a vacuum hose that was leaking, so they put on a new clamp but everything else checked out okay. Ok, so now it starts fine every time, but today it did that high RPM thing again when I put it into Park. It doesn't do it every time, but the RPM will just go up randomly then go back down and go back to normal. Should I clean the IAC with some type of carb cleaner to get out any carbon deposits? Or could it be a bad MAF sensor? Not sure what the symptoms are of that. Everything else seems to be okay now except for the random high RPMs when in Park and sometimes at startup too.

It's a 2 WD, V6 engine.

View 3 Replies

Ford Transmission :: 2007 E350 - Shudder When Accelerating In OD - Whine In Park / Neutral

Looking for your collective expertise

2007 E350 with 5.4L and 4R70W trans. 107K miles and the fluid has probably never been changed ( my mistake - thought it was 100K interval - finding out from my reading that is def not true ). Anyway, following is recent development (last couple days):

Symptom #1: In Park/Neutral there is a whine. As soon as you put it in P or N, the whine 'spins up', stabilizes, and does increase with engine RPM.
Symptom #2: Hesitation (albeit minor) when starting from stop in D and R, with _very_ minor shudder. Sometimes feels like it's struggling a bit to move its own weight just until it's rolling.
Symptom #3: Shudder when accelerating in OD. No shudder when I turn off OD. It does not stop when applying brakes (a test suggested elsewhere). Also, the shudder does not happen when applying gas while braked in D at standstill. Only at highway speeds (enough to be in OD).

This all started at the end of a trip (90 miles or so in 85-90 degrees) when I was pulling a utility trailer (maybe 2000 lbs loaded). Not sure if related, but traction control warning went off a couple times. I think I have a axle seal leak that may be triggering that.

Otherwise shifts fine (no change in shift behavior or smoothness). Things seem to be worse when it has heated up. Should I start with a fluid change? Wasn't sure because there are comments out there saying don't do it or the tranny will just fail faster (I am skeptical).

View 3 Replies

Prius (2004-09) :: Red Triangle Of Death - Car Would Start But Only Go Into Park Or Neutral

The car is a 2005 Prius II hatchback @ 70,000 miles. I like my local garage and they have a good reputation but bad things keep happening. I'm ready to lose my temper but I don't want to. Here's the summary:

3 weeks ago - Started getting the red triangle of death. Had trouble starting. Finally, the car would start, but only go into park or neutral. Towed to garage. Garage put in a new 12 V battery. The car drove away from the garage nicely.

View 10 Replies

Ford Wiring/Electrical :: Analog MLPS Neutral Safety Switch Shows Continuity In Neutral But Not In Park

I have a '94 E4OD trans in my '53 F100. It uses an analog MLPS for the gear selection indicator, Neutral Safety Switch, and Backup light.

My MLPS Neutral Safety Switch shows continuity in Neutral, but not in Park, I need to be able to energize the starter solenoid in both Park & Neutral.

Shouldn't the MLPS show continuity in both Park & Neutral?

View 5 Replies

Toyota - Camry :: 2000 Won't Start When Warm / Gear Shift Lever Is Not Finding Park Or Neutral

My Daughter owns a 2000 Camry. It has a very annoying habit of not starting when it is warm (think driving to the gas station, turning the car off to fill it and then it doesn't start again). We have tried new solenoids, a new starter and several other tweaks but nothing seems to fix the problem. Recently she discovered if she jiggles the gear shift lever (it's an automatic) it will start. So, obviously she gear shift lever is not finding Park or Neutral so that it can be in position to start. She has experimented with this concept and it appears to be the only thing that consistently solves the starting issue. What would we have to fix in the gear shift lever, or elsewhere, to fix this problem?

View 5 Replies

Santa Fe (CM - 2007-12) :: Neutral Safety Switch Replacement

Looking on replacing my Neutral Safety Switch. Shifting the Transmission began to get very hard to do, like the linkage was binding up. Pulled center console, latching mechanism unlocks when i apply the brake, was able to shift with much difficulty into reverse and now i can only get it to shift between reverse and neutral. It is all cable from shifter to transmission and the cable seems fine, no binding there that I can see. Got the nut off the trans linkage but can't get the shift arm to come off the rod and removed the 2 bolts on the safety switch but nothing wants to come apart. Just rusted on? Don't want to use the BFH and break anything.

View 5 Replies

Santa Fe (CM - 2007-12) :: 2008 - Whine When Trans Warms Up And Is In Drive Or Reverse / Not In Neutral

The car has about 53k miles. The problem has persisted since probably 20k miles. The whine is only after the trans warms up and is in drive or reverse, not in neutral. Whine is while the car is stationary or moving at low speed. The whine doesn't seem to change due to gear it is in. It does not change frequency with engine RPM. It does seem to diminish the more load the transmission is under.

Whine is probably not an accurate description, it sounds like a noisy pressure relief valve. Had Hyundai service look at it and all they said was all pressures in the transmission are normal. They could not find any cause.

It sounds like a bunch of small ball bearings running in a loop and can hear each one impact. Sharp raspy impact type sound.

You cannot hear it from the interior but it is quite pronounced while in the garage or if you hear the car coming down the driveway.

View 9 Replies

Santa Fe (CM - 2007-12) :: 2008 - Grinding Noise Coming From Front Of Vehicle When In Neutral

When I start my vehicle, it makes a grinding noise, sounds like it's coming from the front of the vehicle, when I put into gear it stops. It started gradual and is getting worse. It's a 6 cylinder automatic, with 108 k miles.

View 3 Replies

Impala - Chevrolet :: 2003 Won't Start - Don't Recognize Park Or Neutral Only Recognize Reverse

I have a 2003 chevy impala that won't start it does not recognize park or neutral but it recognizes reverse drive and 321 I'm thinking it's the safety neutral switch which I think is in the transmission. I can jump the solenoid and it will start.

View 1 Replies

Santa Fe (CM - 2007-12) :: All Doors Unlock When Put The Car In Park

I have a 2012 santa fe , when I put the car in park all doors unlock , is there a way to change this ?

View 5 Replies

Ford - Mountaineer :: 2004 - Died While Driving And Rarely Start Back?

friend with their Mountaineer issues and i have no clue where to go or what to do now. Shes had it for approx 2 months and didn't have any issues till this one. It died on her while driving and would rarely start back. She had it towed to a crappy garage and the lazy mechanic stood beside it and "listened" for the fuel pump. He said he didn't hear it, gave her a quote and walked away. She then had it towed home and i was contacted. If i get under the truck while she turns they key on, i can hear/feel the fuel pump. It's quiet, but there.

But now, you can turn it over for about 10 seconds and it will start the almost immediately die. During one of the times before she had it towed, she took it to auto zone and had the codes pulled. I have a scan of all the detailed info i can post if needed, but it pulled: P2104 P2106 P2111 and P2135. Each of those mean something along the lines of a sensor but the only two sensors mentioned in more that one code is the throttle position sensor (TPS) and the Electronic throttle control (ETC). I've been trying to research what i can on it, and from what I've read is when these codes are pulled, those two sensors are rarely the problem.

View 7 Replies

Santa Fe (CM - 2007-12) :: Whine Noise In Engine While In Park

On my 2012 Santa Fe I'm getting a whining noise from the engine while it is park. I think it might be alternator.

View 3 Replies

Santa Fe (CM - 2007-12) :: Disable Park Sensor Sound?

Is there any way to disable rear park sensor? I don't like the sound, but I want to disable it, also allowing to enable it again if needed....

View 1 Replies

Santa FE SM (2001-06) :: Won't Go Into Park Or Start

I have been getting a 2006 Santa Fe GLS A/T back on the road for friend who let it sit for almost 2 years because the bumper had gotten knocked off. I charged the battery to get the car to start and it started up OK, but the front brakes were shot completely. I then proceeded to replace the front brake pads and rotors, and when I went to start the car again I noticed something peculiar.

The car wouldn't start, or even attempt to (didn't here it cranking at all). I know the battery is good, and all the other components in the car turn on when I turn the key to A/C setting. I have the shift lever in what would seem to be Park, but the light on the console shows it is Reverse. It shows the car is in reverse when I have it in Park or Reverse, and shows Neutral when I have it in Neutral.

Before I did the brakes (which I don't believe to be related) it was being a bit fussy about switching gears and going into park, but it was definitely working.

View 10 Replies