Ford Ranger / B-Series :: 1999 - Clutch Safety Starting Switch Going Out
I have a 1999 ford ranger and I believe my Clutch safety starting switch is going out. Some times I push my clutch in and truck starts fine other times it will not turn over so I stomp clutch and then it starts. My question is, is there any way to bypass this switch?
View 5 RepliesFord Ranger / B-Series :: 1985 - Fuel Pump Wires Heating Up Intermittently At Inertia Switch
1985 2.3L... New fuel pump And fuel pump relay, problem was happening before new parts. the wires at inertia switch continue to get hot switch has been removed. The heat continues to under the hood where there is some so rt of connecting link and heat stops.what the is this link for, it doesn't look like A fusible link?? Saw a similar post here about a fuel pump shutting down and wires getting hot. Same problem.
View 9 RepliesFord Ranger / B-Series :: 1988 2WD Dies When Clutch Is Released
My Grandpa has an 88 Ranger 2wd with the 2.9l V6 and a 5 speed, I believe, M5od. I was driving down the highway when I heard a noise. I tried throwing the tranny in neutral but when I pressed the clutch pedal in, I had no pedal whatsoever. Engine took awhile to restart. It'd turn over a little almost as if a rod was bent or something of the sorts. Eventually the engine started and would stay running as long as the clutch was pressed in (disengaged).
The engine dies no matter what range the transmission is in,neutral included unless the clutch pedal is depressed. It Will die when the clutch is released in any gear with no forward movement that is noticeable. I can spin the tail shaft with the driveshaft installed and all gears in neutral but the input does not spin at all. Input shaft wont spin at all, period. I originally thought the slave cylinder was KIA but now I am very confused on what the problem could be? Is there a bearing the input shaft rides on that may of seized?
I pulled the tranny last night and took the top cover off. Yes, I made sure it was in neutral when I removed the cover. I can manually shift the collar to all gears by hand, 5th and reverse included. I'm stuck between a rock and a hard place here and where to go from here. I have bought a new clutch assembly and slave cylinder. This truck was bought by my Grandpa brand new in 1988. It has 98,000 miles and everything is original. I did forget to mention that there was very little oil in the trans when I drained it and it appeared to be gear oil vs ATF.
Ford Ranger / B-Series :: 1988 - Master Cylinder Rod Falling Off Of Clutch Pedal
I have a 88 ranger supercab 2.9l 4x4 with the fm146 trans and recently I have had a problem with my clutch master cylinder rod falling off my clutch pedal. I bought the new bushing and put it on and it was fine until yesterday. It wants to keep coming off. Is there a clip of some sort to hold it on or no. I looked at a few at the salvage yard and they did not have a clip just the bushing. So what do I do?
View 1 RepliesFord Super Duty (1999-2016) :: 2002 F250 - No Clutch Safety Switch
2002, F250, 5.4L, ZF-6 trans.
Ok...today by accident turned the key with the truck in gear and clutch not depressed...much to my surprise the truck tried to start and lurched forward.
Is this a sign of a failing clutch safety switch or Could it be an ignition switch problem? Anything else that I am not thinking of?
Chevrolet - S-10 :: 1995 - Changing Clutch Safety Switch?
I need to replace the safety switch on my 1995 S10 w/ a 5 speed manual tranny. It doesn't seem to want to come out. Looking at the new one, I would guess that it MAYBE fits in sort of like the holes on a wall hanger. You know, sort of a pear shaped hole that a screw or something fits into and slides down to make it stay. Am I right? And if so, how hard is it to get out/replace? I don't really want to destroy the old one, but that is looking more and more like how it's going to happen.
View 17 RepliesFord A/C :: 1988 E150 - Clutch Cycling Pressure Switch?
How would I test (if Possible) the A/C Clutch Cycling Pressure Switch on my 88 E-150 4.9L? I had to replace the evaporator, it was leaking along a seam. I have a feeling the Cycling Switch is bad too.
I was hoping for a simple test w/o Gauges. The Switch is in a real tough spot to remove it. I also heard they could be adjusted. There are no leaks in the system and no blockages, that we detected when we evacuated and recharged the system.
Ford Ranger / B-Series :: 2001 - Turns Over Great But Will Not Start After New Plugs And Wires
2001 Ford Ranger 4.0 - 250k miles had the original plugs and wires ....
First things first - I changed them one at a time and confirmed the truck started and ran after each one was changed. I changed all the plugs on the drivers side with no issue. 4,5,6 ... Then I changed plug 3, rear passenger side plug closet to the firewall.
Truck will not start, turns over great, but will not start. I have confirmed I am getting spark. No clue what could have changed, I just pulled out the old plug and wire put in a new one and it wouldn't start.
My father-in-law said if you have spark check fuel. I recall seeing a post about someone breaking a cable for the coil pack but i have checked and i see nothing broken.
Ford Ranger / B-Series :: 1988 - Headlights Won't Turn On At All?
I have a 1988 ford ranger and my headlights won't turn on all my fuses are fine but no headlights! All the other lights work fine blinkers, parking, brake ,and tail lights! What do I need to look for????
View 14 RepliesFord Ranger / B-Series :: 1988 - Overheats While Idling?
My 88 2.9 ranger keeps heating up badly while idling. Was waiting in the drive-thru at Wendy's and it was taking them longer than usual, the temp guage started climbing closer and closer to 'H'.. I revved it up a bit to a fast idle (1500-2000rpm) and it did not work much... figured the gauge was being screwy. But when i finally got my food and started moving the truck was pinging..it really was hot..
But as soon as I got her moving at a steady 40mph, engine cooled back down to normal temp as if nothing ever happened..i put an extra wide two row aluminum radiator from a 4.0 explorer in it, fan clutch is not very old, no coolant leaks that i can see.. can't figure out why it heats up so much so fast at idle. Not enough air or coolant flow?
Ford Ranger / B-Series :: 1988 - Won't Start - No Spark
Any way to tell if the ECU is faulty? I hooked my analyzer up to my friends 1988 Ford ranger 2.3L and it wouldn't even detect that the ignition switch was on. He was driving it the other day and is shut off on him while he was making a turn and it wouldn't start back up. We have rebuilt the distributor by replacing the pick-up, rotor button and cap, and we had the ignition module tested and found it was good. We have also replaced the coil. When the ignition is turned to the on position, the fuel pump comes on and never cycles off.
View 8 RepliesFord Ranger / B-Series :: 1988 - Won't Idle - Starts Right Away Then Die?
88 ranger. 2.9L manual. Just bought this truck. It ran great when I bought it. After a day or 2 it would idle rough. Almost die but it wouldn't. No check engine light. It seemed to do this intermittently. Some times I'd start it and it be fine. Other times I'd start it and I'd expect it to die at each stop light.
Now for the last couple days it dies on every start up. It won't idle. It'll start right away and then die. I can keep it going by keeping the engine rev'd but the check engine light is one. If I keep it running and start driving down the road it'll drive with the check engine light on for about 5 minutes. Then the light goes out and it runs like normal, even at idle, until I shut it off. Then it's the same story at next start whether it's right after I shut it off or hours later.
It doesn't seem to matter whether the engine is hot or cold. When the check engine light is out, it runs great the rest of the time whether at speed or at idle. To me it sounds like a sensor is on it way out. I figure if it was vacuum, it happen at every idle, and if it was fuel it happen all the time or at least every idle. Tried to get a code at parts store but the reader wouldn't work. It couldn't tell it was plugged in the the truck for some reason.
Ford Ranger / B-Series :: 1988 XLT V6 Won't Start Just Crank
I have tried about everything i know about cars on this truck!! It ran great when I got it until a head gasket got blown so I tore into it and replaced them both torqued heads to specs. Made sure valves wasn't to tight. Distributor is in correct spot timing is correct had ignition module tested good!!! Coil tested good replaced both fuel pumps and put new tank and sending unit in the truck b/c it needed it new fuel filter replaced return line firing order is correct 1 4 2 5 3 6 it is getting fire it will crank and crank sometimes act like it is going to start then not also I can get it to run for about 3 sec on 3 or 2 cylinders it seems to have plenty of compression as well!! only thing really I can think of that could be wrong is computer? Also one last detail tried pull starting it as well still wouldn't go.... V6 2.9L...
View 9 RepliesFord Ranger / B-Series :: 1988 - How To Tightened The Valve
It's an 88 2.9 and sounds like a little diesel! The fellow I purchased it from said the valves need tightened, I thought perhaps a timing chain, but figured valves would be an easier place to start. Yet, I'm not sure where to begin? Or how tight the valves need to be, are there torque specks?
View 2 RepliesGolf IV R32 :: Exhaust Leak Melted The Wires On O2 Sensor
So i have an exhaust leak that melted the wires on o2 sensor bank 1 sensor one. This put o2 sensor bank 1 sensor 2 into lean mode and i found this out last week. Made the appointment. Was gonna run some test and replace the o2s if needed. But this morning i go to leave for work and my coolant light comes on 50 feet up the road. I pull over look at my coolant. There was about an inch of coolant left in the tank. Roll back down the street turn the car off and leave it. Im thinking i blew my head gasket running lean. When i get back from work the coolants in the same spot so i jack the car up to see if i can find the coolant leak and i dont see anything. Drop the car back down and the coolant levels back to normal so im alittle lost on whats going on here.
Also after work before coolant level returned to normal i reved it up it blew a little white smoke then black. Nothing really dark. It was quite faint. And also the coolant in the tank would bubble from the back under rev when it was low. Nothing at idle. When coolant level returned. I didn't see any smoke at all and i was unable to check coolant.
Ford Ranger / B-Series :: 1988 - Turn Signals Not Working
I have an 88 ranger with the 2.9l. The headlights work and the markers do to. The brights don't though. and also none of the turn signals work, the brake lights work though but i don't think the reverse do, I can't see them. Do the turn signals and brights share a fuse on there own? How to diagnose it or what it may be?
View 9 RepliesFord Ranger / B-Series :: 1988 - Missing / Stumbling Especially At About 55 MPH While In Overdrive
I've got a 1988 2wd Ranger with a 2.9l v6. I just recently got it running. It has been setting for awhile. I replaced fuel tank, both pumps, fuel filter, Plugs, Wires, Cap, Rotor, TPS. It ran great for about 100 miles. Then yesterday on my way to work about 4 miles down the road it started to miss/stumble especially at about 55mph while in overdrive. When I got home I pulled the codes and I got KOEO 22 Map sensor signal out of voltage(engine off), 53 TPS signal voltage to high, 95 Thermactor Air System Problem, or Fuel Pump Monitor signal, indicates circuit problem.
KOER I got 21 ECT sensor signal voltage out of range or loss of signal during normal operation or Crank Sensor problem, doesn't have a crank sensor I believe. But I did change the ECT sensor and it still stumbles and seems like it misses. Noticed it is sluggish getting up to speed kinda surges and bogs. Im at a loss it isn't showing any more codes. Checked all plug wire connections and made sure everything was making connection. The only other thing I can think of is that the ignition module on back of distributor is going bad. Not advancing the time correctly.
Ford Ranger / B-Series :: 1988 4x4 - Stalling / Cutting Out Sputtering
When I'm driving it starts to cutout (but it never dies) and it won't stop cutting out until I floor it and then it's fine for a little bit and it starts doing it again.
View 1 RepliesFord Ranger / B-Series :: 1988 - Power Loss Like Coil Getting Bad
Bought my third 88 ranger today, drove it 55 of 60 miles home and it died. It lost power and acted like the coil was going bad. This one is a 2.9 5 speed 4x4. The a/c compressor is gone; but the 365 a/c works okay, or did.
My daughter was following me in her car; by the time we got back with my F150 and a chain, it started and ran until it was a half maile from home then lost power and died again.
Drug it home, put a new coil on and it started and revved up fine. Went to move it a couple of hours later and it will crank with the starter, but not fire.
I am getting 12 volts to the primary side of the coil, is there any way to check the TFI module without taking it off the distributor? (they are so accessable).
Or is there something else that I need to check? I really don't want to just throw money at it, I like to know for sure what is wrong before I buy parts.