Santa FE SM (2001-06) :: Key Stuck In Ignition On Accessories Position

I have a 2001 Santa Fe, and the key is stuck in the ignition. I can't even get it to turn to the Lock position, so it's stuck in accessories. Since I haven't had the funds to do so, I haven't gotten it checked out yet, and it's started to drain my battery. I have to jump it every single morning, so I'm wondering if there's anything I can do until I can gather up the money to fix it.

I have tried moving the steering wheel and shifting it all over the place and spraying DW-40 in there and a whole bunch of other things I've seen work for people on a bunch of different forums, but nothing works. I don't know if this matters, but before it got stuck, it would sometimes be hard to pull out or push the key into the ignition.

View 4 Replies

Chevrolet - Cavalier :: 2001 - Cannot Turn Ignition Off / Key Stuck To On Position

It's a 2001 Chevy cavalier. The key is stuck and won't turn the car off. Already have tried shaking the wheel and wd-40. The wipers won't work and the gauges won't turn on until I jiggle the key.

View 4 Replies

1997 Bravada Won't Start - Key Stuck In Ignition In Accessory Position

I have a 97 Bravada. Recently the check engine light came on and then went off. I didn't think anything of it at the time till the other day I drove it to work and back fine without any issues, then the next morning I tried starting it and nothing happened. No cranking, no interior lights, no sounds.

I tried jumping it thinking the battery was dead but that didn't work. Now my key is stuck in the ignition in the accessory position. It will not turn all the way back to release the key.

View 11 Replies

Santa FE SM (2001-06) :: New Key Stuck In Ignition

I have a 2002 petrol, manual, 2.4 Santa Fe

It only had one key when I got it so I ordered a replacement key online -uncoded and uncut. When it arrived I got it cut - looked good. Before getting it coded I thought I would just test the cutting. Opened doors ok so tried it in ignition - fitted and turned engine over - did not start as not coded I presume.

However, when I tried to get the key out again it would not come out. Could this be to do with it's transponder not being coded? Any way I can get it out??

View 2 Replies

Ignition - Chevrolet - Trailblazer :: 2003 V6 2WD - No Start When Key Turned To Start Position

have an issue with my 03 trailblazer. i have the problem of no start when key turned to start position. actually nothing happens when the key is turned to start position. dash comes on when key is turned to on pos tho. took battery off and had it tested and it is at full charge. took starter off and had it tested and it passed. checked ignition relay cavities per this youtube video "Chevy Trailblazer no crank testing and information" and there is no light when touching the ground request cavity and turning the key to start position.

View 3 Replies

Ford F-150 - 1997-2003 :: 2000 - Won't Start When Put The Ignition In On Position

Have 2000 Ford XLT Extended Cab 4x4 with 5.4. It will not start. Put the ignition in on position and can't hear the fuel pump running. Fuse Okay, Relay OK. Does this year have A Fuel Pump Driver Module? If so, where is it located? I know where they are located on 2004 and up but not mine. If I have to change out Fuel pump, is it easier to pull the tank or the Bed?

View 6 Replies

Ford Excursion :: Ignition Switch Stuck In Off Position

None of my 4 keys will operate my ignition switch.

It's stuck in off position. Steering wheel is not locked and I have pulled pretty hard on it to see if I could get the ignition switch to turn.

I have a new switch on the way but I have to get the old one out and don't know how to get old one out if I cannot turn the switch to on position.

View 14 Replies

Saturn - Outlook :: 2007 XR Key Will Not Turn To Off / Stuck In ACC Position In Ignition

The key will not turn to off, stuck in acc. I have no power to the windows, sunroof, seat and seat heaters, and no brake lights, and the mirrors have no power either. I took the car to the local GM dealer who told me the ignition was not in any recall and found that the Body Control Module was bad and needed replacement.

View 5 Replies

Cavalier :: 96 - Key Started To Randomly Get Stuck In The Middle Ignition Position

Quite awhile ago my key started to randomly get stuck in the middle ignition position but it was happening very rarely and some gentle jiggling was letting me take it out easily. Well a few days ago that went from very rarely to each and every time I start the car.

Now its a tossup whenever I go somewhere whether the key will pop out like it should or I'll have to fiddle with it for anywhere up to ten minutes.

The car never has a problem starting, its only when I have arrived somewhere and need to take the key out that is an issue. I've managed to remove it every time so far but it has taken a fair amount of WD-40, jiggling the bejeezus out of the key and steering wheel and plenty of patience.

View 2 Replies

Phaeton :: Move Selector Lever To Position P - Key Stuck In Ignition

I have a European Phaeton 3.2 litre V6 (gasoline) from 2003 that is giving me some problems. When I am finished driving I put the gear lever to parking position and turn off the ignition. I then get a message "Move selector lever to position p" and the key is stuck in the ignition.

So far, I have been able to get the error message away (and with that also been able to get the key out) by starting the car and move the gear lever around. Some times I have managed by only starting the system (by not holding my foot on the brake pedal). But tonight I couldn't get it fixed after numerous tries. I then simply waited in the car, because I didn't really know what to do, and after maybe five minutes the system shut down (energy saving mode?) and I could finally get the key out.

When I tried google the error message I found some topics about it on the Touareg forums, but they got the error message while driving and it had to do with the keyless system (which my car doesn't have).

What might be causing this problem? My local VW dealer is not very used to Phaetons (I am the only on in my town with one).

View 9 Replies

Ford Ranger / B-Series :: 1996 XLT - Ignition Key Stuck In Off Position

My ignition key is stuck / locked in the off position. The first time this happened I jiggled the key while moving the wheel back and forth and it turned. The next time in the truck nothing worked. I let it roll back a bit then tried, pushed the clutch in and put it in neutral, etc it did not move. (Just had the clutch and clutch hydraulics replaced.) The wheel is locked. The key removes from the cylinder.

I know it is easy to replace the Ignition Lock Cylinder when you can turn the key in the run position. How to remove it when locked in off?

View 4 Replies

Santa FE SM (2001-06) :: 2003 - Crank Position Sensor Blown

I've a 2.0L Santa Fe CRDI 4WD, 2003. My Crank position sensor has blown. My question is, does the timing belt have to be replaced with the sensor, or can the sensor be replaced alone? I know the belt must be replaced with petrol models but I've been told it may not be necessary with diesels.

View 1 Replies

TrailBlazer :: 2002 Envoy SLE - Stuck In Park / Ignition Will Not Go Into Lock Position

I've recently purchased an 02 Envoy from an auction. There are a couple of issues. The main one started last night. While at the store I put the truck in park and turn off the ignition. The ignition will not go into the lock position. I messed with the key and go it to turn off. Then started the truck to leave and couldn't put the truck in gear. I messed with the shifter and was able to put into gear.

At that point the gear shifter would move from park to reverse without me pushing the break pedal. I drove home and could not turn the key all of the way off again. Moved gear selector from 1st to Park a few times and then was able to remove the key. I restarted the truck and could not move the gear selector again; however I was able to remove the key easily.

I am leaning towards replacing the "Neutral Safety Switch" on the tranny but with my symptoms, I've seen brake light switch, ignition, and solenoid at gear shift selection.

Back up lights do not work either. Since I purchased the truck, I've replaced,

-Battery
-Ignition Coil

View 9 Replies

Ford Ranger / B-Series :: 1996 B2300 - Ignition Stuck In On Position

Took my 96 B2300 2WD SE (190k) to lunch. When I went to start it back up afterwards, the key turned but no starter engaged. All the dash lights came on, and now stay on. With the key in, I can turn the ignition freely...no clicking to different positions.

It springs a little when I turn it all the way, but still no starter. When I remove the key, the dash lights stay on, etc. So, since it was on, we were able to push-start it. I've parked it on a hill for now, and will disconnect the battery when I get it home.

View 6 Replies

Santa FE SM (2001-06) :: Car Won't Start - Key Wouldn't Turn In Ignition

I have a 2003 Santa Fe with AWD, automatic, and 3.5L engine. Saturday I went to get in and key wouldn't turn. Tried to mess with shifter and steering wheel but no go, Wife got it to turn after I went to work. Won't start. Waited for a new ignition lock cylinder then replaced today. Still won't start. There is no chip in the key as far as I know and the kill switch thing is still plugged in. Jumping does nothing. Doesn't even try to start or do anything when I turn the key all the way. What am I missing here?

View 5 Replies

Accent LC (2000-05) :: 2004 - Key Stuck In Lock Position In Ignition / Wheel Locked

My 2004 Accent is stuck in the "lock" position in the ignition, and the wheel is locked and barely turns in either direction. I know this is supposed to be an anti-theft feature and I've tried all of the solutions listed here...

Turning the wheel hard and soft in either direction while holding the brake all the way down and trying to turn the key. Putting the car in neutral and then park and trying the above Disconnecting the battery for a few minutes and trying the above Jacking the car up on one side to release the tension on the pin.

My question is can I remove the spring at the bottom of the locking pin by drilling a hole in the center of the plate? I've seen a few youtube videos of this done on BMW's. It will cost me $500 minimum to replace the ignition or steering column based on quotes I got.

View 10 Replies

Santa FE SM (2001-06) :: Taking Multiple Tries To Start - P0340 Camshaft Position Sensor Circuit Code

02 Santa Fe 2.4L/ automatic/2 WD. I replaced the fuel filter (only) and have had a nightmare ever since. It takes multiple tries to start, running a little longer each time. When it will finally stay running, only the most delicate of throttle feathering will allow any RPM's to be built up. Any attempt to do otherwise will result is sputtering, bucking and other unhealthy behaviors until the throttle is closed. It also gives off the smell of running rich.

I borrowed a scan tool and got P0136 and P0141, which I expect since the O2 sensor wiring was cut in two by the heat shield shortly after my daughter bout the vehicle. It also is giving me the P0340 Camshaft Position Sensor Circuit code. I had replaced the CMPS and its connector a couple of month ago. I replaced the sensor again to no avail. I have checked the Orange/Black wire from the connector to the ECM and it reads 0 ohms. I get battery voltage at the connector on the Blue supply wire but only get 1.86 to 2.0V when I check the signal with the engine running.

View 6 Replies

Santa FE SM (2001-06) :: 2003 - Ignition Key Rotating Freely Without Starting The Car

The key in my 2003 Hyundai Santa Fe is rotating freely without starting the car. The Accessories are always on and I had to disconnect the battery to prevent drainage. I removed the lock cylinder and found a small camshaft like part that seems to be loose and broken, one piece of it seems to be broken in the switch. Is there anywhere I can get this camshaft like part? I searched but can only find either the lock cylinder or the switch. See the attached pic for the part I am talking about.

View 3 Replies

Santa FE SM (2001-06) :: 2003 - Ignition Lock Cylinder Removal

A few days ago my ignition key would not budge when I tried to start my 2003 Santa Fe. I tried all the tricks like turning the wheel. dry lube, etc but no luck. All indications are that I need a new ignition lock cylinder but I can't figure out how to remove it. I removed all of the plastic and metal shrouding below the dash but can't seem to find a hole to release the cylinder. I have also tried to remove the whole cylinder body assembly by disconnecting the wires and loosening the bolt that secures the "arm" from the ignition cylinder body to the steering column but that also seems to be secured in a way I can't figure out.

View 3 Replies