Ford Ranger / B-Series :: 1996 XLT - Ignition Key Stuck In Off Position
My ignition key is stuck / locked in the off position. The first time this happened I jiggled the key while moving the wheel back and forth and it turned. The next time in the truck nothing worked. I let it roll back a bit then tried, pushed the clutch in and put it in neutral, etc it did not move. (Just had the clutch and clutch hydraulics replaced.) The wheel is locked. The key removes from the cylinder.
I know it is easy to replace the Ignition Lock Cylinder when you can turn the key in the run position. How to remove it when locked in off?
Ford Ranger / B-Series :: 1994 B2300 - Grinding When Downshift To 4th / Stuck In 1st Gear
I bought the 94 B2300 from a guy that said he got it from an auction and didn't know much bout it. Got 30 mins down the road and went to down shift to 4th coming into town and all I got was grinding. Turned it off and it would go into other gears and start in gear with the clutch pushed in. Wen I tried to take off it wouldn't move and just died. Towed it home and installed a new clutch kit in it. Got the clutch bled and went to test drive it and now it is stuck in 1st gear. Can it be easily fixed or am I going to have to replace the transmission...
View 3 RepliesFord Ranger / B-Series :: Camshaft Position Sensor On 1996 2.3L
My check engine light came on about a week ago and was unsure what the problem was. So I tested the codes and it said that the camshaft position sensor was bad. So I have tried finding this sensor but little to no luck. I was unsure if it was the 2 or 3 pin, but after looking at some pictures of the engine I'm thinking it is a 2 pin. I attached two pictures of what I think might be the sensor? But I am unsure. This was right next to the timing belt cover, which is where it said it was located. I have a 1996 Ford Ranger, 2.3L.
View 6 RepliesFord Ranger / B-Series :: 1996 - Ignition Coil B Went Bad?
My engine has 2 ignition coils, and b went bad, but which one is b. ?
View 9 RepliesFord Ranger / B-Series :: 1996 - Ignition Lock Cylinder Won't Reinstall
My keys got stolen from my ignition (battery had died because key was left in ACC and I assume the attempted car jack ended in a key theft for some reason.)
The Ranger is 96, tilt steering with plastic shrouding and column shift A/T... I followed the procedure recommended for exchanging the cylinder without the keys:
-drilled retaining pin
-drilled key slot
-manually removed parts with needle nose
-cleaned, greased and went to reinstall.....
I discovered the small metal washer between the green plastic washer and the gear was broken in half because I nicked it with the end of the drill bit. I inspected this and from what I can tell it looks like the green plastic washer is designed to hold onto the metal washer, the two of them together, from what I gather are designed to keep the gear from moving sideways or tilting. I figured that the washer should do it's job even in two pieces if I could get it in there straight and get the green washer to grab it.
Anyway I stuck it all back in there, slid the new lock cylinder in in run position, and nothing good happened. It's in the whole way, I can see the retaining pin centered in the whole from underneath, but when I try to seat the retaining pin it won't budge. I tried to align the parts at a million different angles and I just have no luck. I am planning on replacing the little metal washer, but I don't feel like it being broken alone is enough to keep all parts from functioning properly. I am stumped because I did the procedure step for step and there is nothing else apparently broken or damaged. The only other factor is that the steering wheel is locked and that sometimes made the other cylinder hard to turn, but it freed up usually with a little wiggling, this cylinder won't budge.
Ford Ranger / B-Series :: 1996 - Fuel Gauge Stuck At Full Mark?
My fuel gauge is stuck at the full mark. What to check and where to start?
View 7 RepliesFord Ranger / B-Series :: 1994 B2300 ECU Relay Intermittently Does Not Come On
Ok I have 94 B2300 and about every 3rd or 4th start the ECU relay will not come on / energize which the the fuel pump relay doesn't come on either to prime the fuel system... so no start! It's very intermittent and sometimes the only way I can get the truck started is by pulling out the ECU relay and plugging it back in even sometimes that doesn't work too. Is it a bad relay or bad base the relay plugs into or is the ECU/computer going bad or is there wiring messed up in my ignition switch? Is there a known problem like this with these trucks?
View 7 RepliesFord Ranger / B-Series :: 1997 - Got B2300 / P0420 Code
I have a 1997 Mazda B2300 with 175,000 miles that has an intermittent check engine light. When I check the code it is always P0420. If I leave it alone long enough the light usually goes out. The truck had the catalytic converter replaced about 5 years and 60,000 miles ago. I also had the muffler replaced in October, but I was getting this code prior to the muffler replacement. I recently bought a scanner that can monitor the fuel trim data and noticed that the long term fuel trim is generally between +16 and 18%. I replaced both oxygen sensors last week and cleaned the MAF sensor, but today I got the CEL again. The LTFT is also still the same as it was before I replaced the O2 sensors. My truck doesn't use any noticeable amount of coolant or oil and I'm not really sure where to start.
View 8 RepliesFord Ranger / B-Series :: 2008 B2300 With Fault Code P1633
I have 2008 mazda B2300 pickup with P1633 fault code. Is this a mazda code (battery overcharge) or ford code (KAM voltage low) since it's a re-badged ranger? Alternator output measured at battery is 14.4 vdc.
View 8 RepliesFord Ranger / B-Series :: Mazda B2300 Turns Over But Doesn't Start
Mazda B2300 2.3L 1995 model... About a week ago I ran my B2300 out of gas (or so I was convinced I was out of gas) because the engine quit running. After adding gas was unable to start it back up. It turns over but doesn't start.
Here's what we did to try and fix it:
1.) Replaced Fuel Filter
2.) Check the fuel pressure, and it was at 35 psi when the key was on
3.) Replaced all 8 spark plugs (4 cylinder truck btw)
4.) Checked spark of all 8 coil pack slots and 1st and 3rd slots (exhaust side) were not sparking. After replacing coil pack we received spark but truck still didn't start.
We're speculating on the possibility of it being the PCM (ECC).
Ford Ranger / B-Series :: 1994 B2300 - Gas Gauge Reads Empty?
Any known problems with '94 Ranger/B2300 gas gauges? I just got a '94 B2300, and gas gauge reads empty with the key ON, and about 1/4 tank with the key OFF. Was told by previous owner it occasionally works, but I've never seen it work. Am starting to procure manuals and dig around the truck myself, but don't want to re-solve the problem if it's a known one. Haven't seen mention on the net of it being a recurring problem, but just starting to dig.
View 6 RepliesFord Ranger / B-Series :: 2.3L Mazda B2300 Died And Wouldn't Start Back Up
I am working on a 96 Mazda b2300 auto 2wd for a friend. His son was driving it when a loud noise, it died and wouldn't start back up. He had it towed to my house, I started to tear into to it and found it slipped the timing belt. So a rebuilt head, gaskets, timing belt, fuel injectors, water pump, thermostat, plugs, and fluids; tried to start it and nothing. Started troubleshooting and found the primary coil pack was out of spec, replaced and still nothing.
Changed out the CKPS still nothing? I have spark, I have fuel, I'm going to check compression tomorrow but the way the cylinders and pistons looked I don't think that is the issue but I going to check anyway, rechecked the timing marks they all lined up. Checked the fuel inertia switch not tripped. Could the PCM, or ICM cause a no start, and still be able to get spark and fuel?
Ford Ranger / B-Series :: 2002 B2300 - Lower Hose That Comes Off Of Coolant Reservoir Leaking
I'm about to tear into a friends 2002 B2300 4 cyl. The lower hose that comes off of the coolant reservoir is leaking in the metal part of the line. Close to where it bolts to the block. At a glance, it looks like I have to pull the whole top of the motor apart to get it off since the line runs around behind the motor. Is there a trick to removing this coolant line without a lot of teardown? I'm not finding it at parts stores so I guess it's a stealership part.
View 2 RepliesFord Excursion :: Ignition Switch Stuck In Off Position
None of my 4 keys will operate my ignition switch.
It's stuck in off position. Steering wheel is not locked and I have pulled pretty hard on it to see if I could get the ignition switch to turn.
I have a new switch on the way but I have to get the old one out and don't know how to get old one out if I cannot turn the switch to on position.
Ford - Ranger :: 1996 Continue To Run When Put The Key Into Off Position
I have a 1996 Ford Ranger which was manufactured in 08/95. The key will crank the trunk fine, but it when put into the off position nothing happens. It continues to run as normal. You can even take the key out, but the truck runs like normal. Could this be bad ignition switch? The key seems to be doing its job because I can see the plastic pin(? I am not sure what its called) move back and forth down steering column when the key is turned.
View 7 RepliesSanta FE SM (2001-06) :: Key Stuck In Ignition On Accessories Position
I have a 2001 Santa Fe, and the key is stuck in the ignition. I can't even get it to turn to the Lock position, so it's stuck in accessories. Since I haven't had the funds to do so, I haven't gotten it checked out yet, and it's started to drain my battery. I have to jump it every single morning, so I'm wondering if there's anything I can do until I can gather up the money to fix it.
I have tried moving the steering wheel and shifting it all over the place and spraying DW-40 in there and a whole bunch of other things I've seen work for people on a bunch of different forums, but nothing works. I don't know if this matters, but before it got stuck, it would sometimes be hard to pull out or push the key into the ignition.
Ford Wiring/Electrical :: 1996 F350 - Driver Rear Door Lock Stuck In Locked Position
My 96 F-350 Crew Cab driver rear door lock is stuck in the locked position. I don't have a cause but do now notice that the pass door lock will not operate with the lock/unlock switch. The rear solenoids seem dead. Front door locks are working.
I tried to put a 10-32 coupling nut on the lock riser and pull. The down position is now 1/8-1/4" higher than normal. This thing is really stuck and is really bad.
So before I start pulling the rear seat and trying to remove the door panel from a closed door; how I might unlock this door? It would be a lot easier to get the panel off if it is open.
Saturn - Outlook :: 2007 XR Key Will Not Turn To Off / Stuck In ACC Position In Ignition
The key will not turn to off, stuck in acc. I have no power to the windows, sunroof, seat and seat heaters, and no brake lights, and the mirrors have no power either. I took the car to the local GM dealer who told me the ignition was not in any recall and found that the Body Control Module was bad and needed replacement.
View 5 Replies1997 Bravada Won't Start - Key Stuck In Ignition In Accessory Position
I have a 97 Bravada. Recently the check engine light came on and then went off. I didn't think anything of it at the time till the other day I drove it to work and back fine without any issues, then the next morning I tried starting it and nothing happened. No cranking, no interior lights, no sounds.
I tried jumping it thinking the battery was dead but that didn't work. Now my key is stuck in the ignition in the accessory position. It will not turn all the way back to release the key.