Santa FE SM (2001-06) :: 2003 - Ignition Stuck In Start Position
I have a 2003 2.4L 5 speed manual Santa Fe. I was parking my vehicle and removed my key as usual and realized that the car was still running. I put it into reverse rolled back and back into 1st to roll forward just to make sure I wasn't dreaming. I ended up pulling the fuel pump fuse and disconnecting the battery to turn it off.
When I replaced the fuse and reconnected the battery I was able to bump start the vehicle without the key in the car and drive it all the way home with no problem. I took apart all the plastic pieces around the Ignition and attempted to remove the cylinder but was unable to locate any sort of small button or pin to push on to remove it. Where is the release button?
What are my options here? Do I replace the cylinder first or get a new key, or is there something else that I should check first before I take it in.
Santa FE SM (2001-06) :: 2003 - Ignition Lock Cylinder Removal
A few days ago my ignition key would not budge when I tried to start my 2003 Santa Fe. I tried all the tricks like turning the wheel. dry lube, etc but no luck. All indications are that I need a new ignition lock cylinder but I can't figure out how to remove it. I removed all of the plastic and metal shrouding below the dash but can't seem to find a hole to release the cylinder. I have also tried to remove the whole cylinder body assembly by disconnecting the wires and loosening the bolt that secures the "arm" from the ignition cylinder body to the steering column but that also seems to be secured in a way I can't figure out.
View 3 RepliesSanta FE SM (2001-06) :: 2003 2.7L V6 Not Starting Or Cranking After Heavy Rain
Several weeks ago I made another thread because I was having crankshaft position sensor problems and essentially that was due to a short on the sensors wires which had become exposed. I replaced the sensor and it still did not work until later trying another brand which solved the problem.
I also changed all six spark plugs, wires, and plenum gasket with OEM parts. I was able to get to the back three plugs by following this tutorial with the guidance of a friend who is a mechanic. After getting this done, the car has run way better and smoother.
However, today it has been raining heavily and I needed to run an errand so I went to my car and turned the key but nothing happened. All the dash lights turned on and appeared normal. My radio works, lights work, etc; but I can not get the car to crank at all. I hear the fuel pump turn on and everything else sounds normal, but still no crank. There are no sounds from the starter at all, it is silent when I try to get the car to turn over.
I took a look at the car and the coil pack seems dry, the plug wires are secure, plus we had put di-electric grease on all those connections. The negative terminal on the battery has a solid connection. I even tried jumping the car to see if maybe it was due to the battery, but again nothing happened.
This has only happened once before when it was raining, before I had changed the plugs and wires, but I was able to get it to crank over after about 4 minutes of waiting and contemplating getting a tow. I took a look at all the fuses and they appear to be intact.
Passat (B5) :: 2001 - Car Starting In EPC Mode After Like 8 Seconds On The Ignition
I have a 1.8T 2001.5 Passat, Tiptronic with an Upsolute chip. I recently had the turbo replaced (under warranty for the same stock one). After the turbo reinstall, the car did this after driving it a while: I ran it hard and spooled up the turbo good a few times, and then parked the car. I would wait 45-60 minutes. When I tried to start the car it wouldn't start for like 8 seconds on the ignition, and then it would start but in EPC mode!
The first time this happened I panicked, drove it home (just to make sure I got home.) I then tried again and it started fine and no more EPC. Also, if I wait much longer like 3 or 4 hours, it never happens. Since the first time, this has happened like 10 times or more. But now, I just turn it off right after it starts in EPC, turn it again, and it works fine.
The first time it happened I got some kind of codes, but I didn't save them and cleared them. I figured since it happened again, I would get the codes again, but they're not there. I took it to the dealer, and of course, they can't duplicate it. The codes where like speed implausible or not there or something but I can't remember now.
The master mechanic told me to vapor lock was not possible because I had no carb, but I seem to remember that my '83 fuel injects 280ZX turbo had a special cooler fan to cool down the injectors in the event of vapor lock after the car shut down so I'm pretty sure this is possible with injectors. I mean, the explanation for that fan was so that if the remaining fuel in the injectors would get so hot after car shut down that it would vaporize the fuel and the pressure would lock up the injectors.
Santa FE SM (2001-06) :: New Key Stuck In Ignition
I have a 2002 petrol, manual, 2.4 Santa Fe
It only had one key when I got it so I ordered a replacement key online -uncoded and uncut. When it arrived I got it cut - looked good. Before getting it coded I thought I would just test the cutting. Opened doors ok so tried it in ignition - fitted and turned engine over - did not start as not coded I presume.
However, when I tried to get the key out again it would not come out. Could this be to do with it's transponder not being coded? Any way I can get it out??
Santa FE SM (2001-06) :: No Turnover Occurring When Put The Key Into The Ignition
I got up on a rainy monday morning to go to work put the key into the ignition and no turnover occurred. Not even a click. Looked like the car had plenty of juice though. Right now my poor car is just sittin' in the driveway. 2005 Hyundai Santa Fe 3.5L V6
View 19 RepliesElantra XD (2001-06) :: AC Tensioner Pulley Won't Spin Freely
I took my A/C tensioner pulley (the pulley that is on the upper left of my crankshaft/harmonic balancer) off and when I took it off, the plates and washer fell off and I wasn't 100% positive how they went back on. I mean I thought I was 100% positive until I tried putting it back on. There are two plates, one on the front of pulley and one on the back. I'm guessing the smaller 1 has to be on the front because it has marks from the nut that goes on the front. The other one in my mind obviously has to be the back 1. The thick washer "seems" to go behind the back plate. It has stain marks on it that line up with the mounted bracket behind it, that is why I say seems. The actual bolt goes in from behind the bracket. The problem is when putting the pulley back on, I tighten the nut (I can't find the torque specs anywhere) in the front and the pulley won't spin freely at all. When I loosen the nut to the point where the pulley can slide side to side it will spin no problem. Something just ain't right but what it is. Are there more parts to this thing that might have rolled off into the abyss? Did I put the parts on wrong?
View 4 RepliesSanta FE SM (2001-06) :: No Click On Starter When Put / Turn The Key In Ignition
I have a 2006 Santa Fe with 137K miles on it. Has been best car I ever owned, but have recently experienced a strange issue where it won't start, meaning I put the key in the ignition, turn it to the right and nothing, not even a click on the starter. I have found if I move the shifter around from P to R to D, etc. and then try it again it will start. Is there a safety interlock switch in the shifter that could be going bad and is therefore not satisfied/happy when I try to start the car? Or could the ignition hardware where I insert the key be the issue.
View 1 RepliesSanta FE SM (2001-06) :: Key Stuck In Ignition On Accessories Position
I have a 2001 Santa Fe, and the key is stuck in the ignition. I can't even get it to turn to the Lock position, so it's stuck in accessories. Since I haven't had the funds to do so, I haven't gotten it checked out yet, and it's started to drain my battery. I have to jump it every single morning, so I'm wondering if there's anything I can do until I can gather up the money to fix it.
I have tried moving the steering wheel and shifting it all over the place and spraying DW-40 in there and a whole bunch of other things I've seen work for people on a bunch of different forums, but nothing works. I don't know if this matters, but before it got stuck, it would sometimes be hard to pull out or push the key into the ignition.
Santa FE SM (2001-06) :: Ignition Knock When RPM Is About 1500 - 2000
Since of lately my 2001 santa fe with about 143000 Km on the clock is having a ignition knock when the RPM is about 1500-2000, also changing to 2nd gear (Auto Box). What it could be and how to rectify it?
View 2 RepliesSanta FE SM (2001-06) :: Car Won't Start - Key Wouldn't Turn In Ignition
I have a 2003 Santa Fe with AWD, automatic, and 3.5L engine. Saturday I went to get in and key wouldn't turn. Tried to mess with shifter and steering wheel but no go, Wife got it to turn after I went to work. Won't start. Waited for a new ignition lock cylinder then replaced today. Still won't start. There is no chip in the key as far as I know and the kill switch thing is still plugged in. Jumping does nothing. Doesn't even try to start or do anything when I turn the key all the way. What am I missing here?
View 5 RepliesSanta FE SM (2001-06) :: Transmission Warning Light Does Not Come On When Turn On The Ignition
I've just bought a 2.0D Santa Fe (I am UK based) and when I turn on the ignition the warning lights light up and then go off - which I believe is the light check.
However, the transmission warning light does not come on during this check period. Is there an easy way to test this? I'd like to know when the 4WD kicks in or there is a problem but don't know if there's a bulb fault or not.
Santa FE SM (2001-06) :: Key Ignition Cylinder Light No Longer Works
2003 Santa afe 2.7 litre: So for some reason the key ignition cylinder light no longer works, but no issues with the ignition at all. What powers the light, is there a specific part of the cylinder I need to check or replace or do I have to replace the whole cylinder. Would a another cylinder I pick up from the junk yard work?
View 11 RepliesSanta FE SM (2001-06) :: 2004 Stays Running After Ignition Is Turned Off?
Ok, so I'm working on a 2004 Hyundai Santa Fe, 93,000 miles. The vehicle runs great! So great that you cant get it to stop running!! The problem is intermittent and generally happens after the vehicle has been running for at least 3 minutes. I turn the key off and she keeps on running (not dieseling, but running at 340-450 rpms!) I have already removed the aftermarket remote start that was installed on the vehicle thinking that was the problem, it was not. Then I went to the ignition switch and unplugged that, also to no avail! I plugged my scan tool in and can communicate with the computer and view pids while the key is on. When I turn the key off, I should loose communication. When everything acting normal and the car actually shuts off with the key, I loose communication with the computer upon turning the key off. When I turn the key off and the veh. keeps running, I do NOT loose communication with the pcm. The only way to shut the car off is to step on the gas pedal. Otherwise it'll run at 400 or so RPM for an hour or so!!
View 8 RepliesSanta FE SM (2001-06) :: Hard Starting After Refueling
When I get gas in my '04 Sante fe it can be very hard to get it restarted. It acts as though its flooded.
View 9 RepliesSanta FE SM (2001-06) :: Revving / Stalling And Not Starting
I drive a 2004 Hyundai Santa Fe V6 2.7L with a whopping 274,3xx miles on it. I've had it for about 6 years and it has been a great car for the most part. The water pump was replaced a couple years ago and the battery was replaced a year ago.
It started having issues a few months ago. It started out having difficulty starting, and shortly after it would start it would rev up as if you were accelerating even if my foot was on the brake. I took it to the shop and they checked the head gaskets, battery, transmission, alternator (I think?). Came up with the idea that it may be the air intake valve. It's the thing that controls how much the blade opens when you press on the accelerator. Well they took it out and said it was the dirtiest one they had ever seen. They cleaned it, because no one in our area had a replacement, and my car seemed to be acting better. It would still rev occasionally and would have trouble starting but not nearly as often as before.
Fast forward to now (a month later) and my car is revving higher and for longer than it ever has and has started stalling, and not starting more frequently. It usually stalls after it has been revving when it cant release or go forward (ex. when applying the brake or while in park.)
What the heck is wrong with this thing?? No one seems to be able to figure it out and it it so frustrating, not to mention dangerous! It stalled in the middle of me making a turn today so I was literally sitting in the middle of oncoming traffic with a dead car.
Santa FE SM (2001-06) :: 2004 - ECU Fuse Under The Hood Keeps Blowing When Ignition Turned On
I have a 2004 Hyundai Sante Fe 2.4L that keeps blowing the ECU fuse under the hood when the ignition is turned on. We have replace the fuel pump and the inertia switch. I have tested the relay, ignition failure sensor, both coils and O2 sensor wiring.
View 10 RepliesSanta FE SM (2001-06) :: After Driving It Won't Shut Off - Replace The Ignition Cylinder Or Switch?
I've been having a "turn off" problem with my 03 santa fe. After driving it doesn't want to shut off. The switch will be in the off position and it just keeps running. When I put it in Reverse or drive and then turn the switch off it stops. But which should I look at first? The ignition cylinder/key replacement or maybe something in the ignition switch/electrical? The cylinder assembly is over a hundred $$ and the switch is only $25.
View 3 RepliesSanta FE SM (2001-06) :: 2004 3.5L - Whine Occurred On Starting The Car
Drove the vehicle today (current at 156k miles) about 40 miles then came back home. Left again to run an errand. After coming out of the store and starting the car, a very pronounced 'whine' occurred. It kept whining for about 2 miles and with 3 blocks left to go, the whine suddenly stopped. No CEL appeared and the radiator temp was normal, oil level was fine and the pwr steering fluid in the reservoir was at the max level. I suspected it might be the p/s pump but, if so, why did the noise cease?
View 1 Replies