Ford Super Duty (1999-2016) :: Replaced 5th Time Rear Brake Caliper And Slider?
one of my f350 super duties has had the right rear brake caliper and slider replaced 4 times in less than a year. it has just gone for the fourth time today. i called ford who, after a long phone call, said it could be the metering valve. i have looked everywhere for this valve.....no luck. so i called them back and he said it was part of the HCU. after a few minutes, he finally told me it was also called the ABS module.
my question is..........can i just replace this metering valve or do i have to replace the whole unit?
Prius (2004-09) :: One Rear Brake Caliper Not Braking Properly
I have a 2007 Prius gen II with 50,000 miles on it. I took it for MOT ministry of transport annual test and it failed on rear brakes. The near side puled 82kg the off side puled 242kg I puled the pads and copper slipped the pads and sliders the piston pushed bake with ease reassembled them and re tested them witch increased the near side by 5kg. How did you rectify it.
View 2 RepliesPrius (Gen 2) :: Pistons In Driver Side Front Brake Caliper Is Sticking
One of the pistons in my driver side (UK) front brake caliper is sticking, so I've bought a second hand caliper just to fix the problem until I come to sell my pri in a month or so.
View 15 RepliesPrius (2010-12) :: Brake Fluid Leaking From Rear Driver Caliper
I have a leak from the rear driver caliper, it seems to come from behind the bolts that hold the emergency brake to the caliper (I had my wife push the pedal repeatedly so I could find the issue). I haven't been able to remove the retaining bolts (the allen head bolt doesn't want to play) to see what the issue might be.
View 18 RepliesLexus GS 2006-11 :: Caliper Nut Can Be Replaced?
I have a 07 gs430 front caliper bolt strip and the caliper nut strip. What can I do? the bolt a 12mm 1.25 ,the tread is strip bad.. can I replace that part..? the nut on the caliper?
View 5 RepliesPrius (2004-09) :: Replaced 12V - ABS, VSC And Brake Lights Came On
Just replaced 12 volt battery from a dealer nearby. Got it in OK, but my "!", ABS, and VSC and Brake lights are still on. Pads and shoes look fine. Is there a reset button or mode for these lights. I was under the impression that the display voltage test of 9 volts (dying battery) was causing the lights to come on. Just want to make sure there is no reset on the lights (like after an oil change) before I move on to other testing or the mechanic. The other symptom I've had along with these lights is the yellow arrows coming from the battery don't stop when I come to a stop. I have to put in neutral or park to get them to stop not matter how hard I press on the brake. This happened a couple years ago, along with the lights above, but went away. I wrote it off at the time to a bad connection somewhere.
View 13 RepliesPrius (2004-09) :: Camshaft Gear And Valve Cover Need To Be Replaced / CEL Came On
Yesterday the check engine light came on in my 2006 Prius. I took it to the dealer, and they said that the camshaft gear and valve cover need to be replaced. Specifically, the diagnostic report says "P0011. Camshaft position A timing over. Advanced or system performance bank 1. Pin point check LED to CUV gear not switching."
View 9 RepliesCamry :: Brake Caliper Moved Out Of Alignment
Last Spring, my 2007 Camry Hybrid (54k miles back then, now at 62k) developed an obnoxious squeal coming out of the left rear wheel while driving at highway speeds. It takes several minutes at this speed to make the sound, so I believe wheel temperature triggers the sound. Touching the brake would temporarily silence it. After parking the car, I discovered that the left rear wheel was very warm, while the others were cool. I also saw excessive brake dust on the wheel.
I pulled the wheel to inspect. and saw that the track of the brake pad had moved a millimeter or two up the disk, so now part of the pad was over the "rusty" portion of the disk. The rusty, unworn part of the disc was thicker, so the part of the pad that was now over it was rubbing. At higher speeds, the rubbing would heat up the wheel and I'd gradually get the loud squeal.
I dismantled the pad, cleaned it, tightened the mounting brackets (via slight bending) and put it all back together. This solved the problem for 8 months. It just came back to haunt me on a recent highway trip...
It's a pain to take it all apart, especially if I am only temporarily fixing the issue. The pads still have over 85% live (including the rubbing one) and the disks look great on all wheels with no vibrations.
Lexus IS 2014+ :: How To Remove Brake Caliper
I've searched, but nothing came up. I want to remove the brake calipers (unbolt from the rotors) for cleaning and painting. I need confirmation that the fronts are just two 17mm bolts on the back of the caliper that is holding it? I tried earlier but it was right after a drive so car was hot and the bolts seemed like they were secured on tightly. I will try again this weekend. Btw. I have a 350 f sport
View 9 RepliesGolf V R32 :: Brake Caliper Color Fading
Noticed blue calipers losing their color? Specifically looking like they have a dull coat of wax on them that doesn't come off with normal washing.
View 8 RepliesSebring - Chrysler :: 2005 - How To Get Brake Caliper Off
I've run into a problem while doing brakes on my friends 2005 Sebring. I can't seem to get the brake caliper off. There is a little rubber boot with a plastic cap that is where the bolts that hold the calipers in place are. How to get the bolts out to remove the caliper. In fact, it doesn't seem like there are any traditional bolt heads in the plastic cover.
View 2 RepliesPassat (B6) :: Electric Parking Brake Caliper Leaking
Today, as i had my car in the repair shop for a checkup i got a horrible message. The rear caliper/hand brake motor (?) is leaking brake fluid. Replacing this is close to 1500$ (I live in Norway) So my question is: Is there any way to stop the leak without replacing the whole thing? Also, i suspect the leak is minor as the brake fluid is almost on "max". So, if it doesn't really leak a whole lot, do i really need to do anything about it? I mean, if i have to refill the fluid container every six months its much cheaper.
View 1 RepliesGTI 337/20th Anniversary :: Passenger Side Brake Caliper Went Bad
Yesterday (well for a while, but yesterday was bad) I had some brake issues, turns out the passenger side front caliper went bad (corroded, doesn't retract) so I need to get another one. Only place I saw Red caliper for my jazz blue for sale was on ecstuning and that was 189. Seems a little steep so I was wondering if there are any other places who sell the Red OEM calipers. If not I might just go through ecs.
View 2 RepliesCamry :: 2007 - Brake Rotor Rubbing On Caliper Bracket
I'm working on a 2007 Camry and I had the wheel bearings pressed in & out at a shop. I put everything back together but the driver side rotor is rubbing against the caliper bracket. And there is no air gap between the rotor and bracket so it can spin freely without rubbing. The passenger side is fine, there is a little air gap so the rotor can move freely without rubbing. I don't understand why the driver side rotor is rubbing against the caliper? I checked everything over, the pads and rotor are the correct ones. I also took the pass side caliper bracket and installed it on the driver side and same thing, the rotor still rubs against the bracket.
View 13 RepliesLexus IS 2014+ :: Changing Brake Pads Without Unbolting The Caliper?
What is the proper procedure in changing the brake pads without unbolting the caliper?
View 7 RepliesCamry :: Installing New Caliper - Separating Brake Hose Fitting?
I'm having a tough time separating the brass fitting, even using a 10mm wrench. I noticed it moves below the bracket, so I'm trying to hold the oval with square corner base on the hose itself, but even then, have started to round the corners on the brass nut.
I'm gonna continue with the job, leaving the old hose, and will have to come back to this later, because I'm installing a new caliper (old one froze, and I just found out why, broken lower slide).
Any trick to separating the fitting between steel brake line and rubber?
ETA, to replace the brass fitting, does it mean cutting the tube, inserting another fitting, and flaring the end? I hate to leave the old hose or a rounded nut.
Lexus GX 2004-09 :: Front Brake Caliper Bolts Frozen
Started to change front pads and rotors on my GX470, but couldn't get the caliper bolts loose. Is it safe to use a torch to heat up the area around the bolts so I can loosen the bolts? Any other way to break these bolts free?
View 12 RepliesElantra XD (2001-06) :: 2004 - Resetting Brake Caliper Pistons?
I need to do a brake job on the front of my 04 Elantra, how to reset the caliper piston. I've tried the traditional c-clamp method but can't get the clamp to grip well on the non-pad side because of the caliper shape.
View 4 RepliesLexus ES 2007-12 :: Torque Specifications For Brake Caliper Bolts
I haven't had luck trying to find the torque specs for the caliper bolts on my 2010 ES350. What are the correct numbers? a pdf diagram would be very useful.
View 1 Replies