Camry :: Installing New Caliper - Separating Brake Hose Fitting?

Camry :: Brake Caliper Moved Out Of Alignment

Last Spring, my 2007 Camry Hybrid (54k miles back then, now at 62k) developed an obnoxious squeal coming out of the left rear wheel while driving at highway speeds. It takes several minutes at this speed to make the sound, so I believe wheel temperature triggers the sound. Touching the brake would temporarily silence it. After parking the car, I discovered that the left rear wheel was very warm, while the others were cool. I also saw excessive brake dust on the wheel.

I pulled the wheel to inspect. and saw that the track of the brake pad had moved a millimeter or two up the disk, so now part of the pad was over the "rusty" portion of the disk. The rusty, unworn part of the disc was thicker, so the part of the pad that was now over it was rubbing. At higher speeds, the rubbing would heat up the wheel and I'd gradually get the loud squeal.

I dismantled the pad, cleaned it, tightened the mounting brackets (via slight bending) and put it all back together. This solved the problem for 8 months. It just came back to haunt me on a recent highway trip...

It's a pain to take it all apart, especially if I am only temporarily fixing the issue. The pads still have over 85% live (including the rubbing one) and the disks look great on all wheels with no vibrations.

View 7 Replies

Camry :: 2007 - Brake Rotor Rubbing On Caliper Bracket

I'm working on a 2007 Camry and I had the wheel bearings pressed in & out at a shop. I put everything back together but the driver side rotor is rubbing against the caliper bracket. And there is no air gap between the rotor and bracket so it can spin freely without rubbing. The passenger side is fine, there is a little air gap so the rotor can move freely without rubbing. I don't understand why the driver side rotor is rubbing against the caliper? I checked everything over, the pads and rotor are the correct ones. I also took the pass side caliper bracket and installed it on the driver side and same thing, the rotor still rubs against the bracket.

View 13 Replies

Ford Super Duty (1999-2016) :: 2003 F250 SD 4x4 - DTC Codes P0171 / P0174 - Loose Fitting Oily Hose?

I've had DTC P0171 & P0174 (lean in bank 1 and lean in bank 2) for a few weeks now (check engine light cued me on it). Autozone scanned it for me. It's on a 2003 F250 SD 4x4 5.4L.

My first step was to clean the MAFS. Light came back on in about 30-40 miles. I then replaced the MAFS. 30-40 miles and the light came back on.

My first thought was disconnecting the battery wasn't resetting the comp and thats why the light was comming back on.

I went and picked up an Actron cheapy OBD II Scanner today at lunch. Cleared the codes with the scanner and drove back to work.

Checked the codes when I got back (no light on but was curious) and it shows P0171 & P0174 pending.

I've checked and the dipstick is seated properly. The hoses on the air intake appear to seated properly as well. The top hose is a pretty loose fit but it was seated all the way down. The top hose was oily. Not sure if this is normal or not. Could the loose fitting oily hose be the culprit?

Also, what is the lower hose? It comes off the back of the air intake and goes to the driver side valve cover. I know it's not the PCV hose as that is on the passenger side valve cover....right?

View 14 Replies

Camry :: ABS Brake - Front Driver Side Caliper Sticking And Heating Up

2005 Toyota Solara my front driver side caliper was sticking and heating up a couple months ago... replaced the caliper and the rotor... still had the same problem. I would drive it, it got hot and stuck, after I parked for a little while it slowly released. Talked to a couple of mechanics and they both said undoubtedly I had a bad flex hose and it was collapsing with pressure and then will release... I changed the flex hose and flushed the fluid and it was immediately fixed...no problems.

Drove the car for a month, went to South Carolina and back and then a couple days ago the same thing started happening. Talked to a mechanic, he told me that the new caliper may have gotten fried from over heating before I changed the flex hose... Got a new caliper today (warranty) exchange... changed it out and still have the same problem. When it sticks I can release the pressure by opening the bleeder valve so it seems like the flex hose issue again... my only thought now is maybe the new flex hose is a bad one and someone mentioned the proportioning valve.

View 9 Replies

Camry :: 2014 SE - Rear Passenger Side Brake Caliper Frozen Open

So, my right, rear, brake caliper froze in the open position a little while back; I hit the brake hard, it held, heard a clack, then it let go and stayed in the open (uncompressed) position. I lost some braking power but at least have been able to drive. No visible brake fluid leak, other three brakes working fine.

At 125K, I've decided to do a full brake job, and am about to search for some of the parts on the awesome stickied parts reference list up above. I'll hopefully find some parts are available at NAPA, where I'm also ordering the right side cv axle.

So, I'm only finding remanufactured brake calipers at NAPA. Are they decent or should I look for something new elsewhere?

View 14 Replies

Regal :: 1998 - ABS Unit To Brake Line Fitting?

I would like to replace the brake line to the rear brakes, and I noticed that the brake line-to-ABS unit fittings have different threads. I already replaced the line to the Left-Rear brake, and it had a fitting with a thread M10-1.0. I tried to replace the line to the Right-Rear brake using a similar fitting M10-1.0, but it did not work. I just damaged the thread on the brake line fitting itself. Then I noticed that the thread on the current Right-Rear fitting is different. what that thread size should be (the fitting to the Right-Rear brake line)?

It is 98 Regal LS 3800 engine.

View 3 Replies

Ford F-150 - 1997-2003 :: Brake Line Fitting Size

Well the time has come where I don't like the way my brake lines look running to the back of the truck. Question is, What size are the fittings on the ends of the lines? I know I will have to special order the line that goes from the frame rail down to the rear axle tube, but is the line that goes from there to mid way frame rail a standard size? I don't want to have to order that if I don't have too.

View 1 Replies

Ford Excursion :: After Standard Brake Line Replacement Fluid Leaking On Passenger Side Fitting?

So I had a stuck caliper on the driver rear side. I pushed the piston back and checked everything to make sure all was in working order. After some though and reading about the calipers getting stuck which old brake lines, I decided to upgrade the line with the Russell stainless steal lines.

I got all the lines put in but I seem to have fluid leaking on the passenger side fitting which I can't seem to get to stop. I put the old line back in but it is still leaking. I am not sure what I need to do or check to get it to stop. It seems to be leaking from the thread area. I checked the fittings and they don't look cross threaded so I don't understand why it may be happening.

View 3 Replies

Prius (Gen 2) :: Brake Caliper Replaced Now Won't Go Into Gear

My wife was complaining about a metallic scraping noise that was coming from the driver side front wheel. I listened to it and couldn't determine what it was or see any evidence of something loose. I took off the wheel and had a look at the components and after 160K miles, it looked like the pads could use replacing. It didn't seem like that was the root of the sound, but it looked like they needed to be done.

I got the parts for both sides and replaced the left without issue, but when I got to the right side, I found the source of the noise: a pebble between the rotor and dust shield. I continued on with the brake replacement and the caliper piston was stuck. Tried a couple of things to free it and blew out the piston.

View 11 Replies

Lexus IS 2014+ :: How To Remove Brake Caliper

I've searched, but nothing came up. I want to remove the brake calipers (unbolt from the rotors) for cleaning and painting. I need confirmation that the fronts are just two 17mm bolts on the back of the caliper that is holding it? I tried earlier but it was right after a drive so car was hot and the bolts seemed like they were secured on tightly. I will try again this weekend. Btw. I have a 350 f sport

View 9 Replies

Golf V R32 :: Brake Caliper Color Fading

Noticed blue calipers losing their color? Specifically looking like they have a dull coat of wax on them that doesn't come off with normal washing.

View 8 Replies

Sebring - Chrysler :: 2005 - How To Get Brake Caliper Off

I've run into a problem while doing brakes on my friends 2005 Sebring. I can't seem to get the brake caliper off. There is a little rubber boot with a plastic cap that is where the bolts that hold the calipers in place are. How to get the bolts out to remove the caliper. In fact, it doesn't seem like there are any traditional bolt heads in the plastic cover.

View 2 Replies

Passat (B6) :: Electric Parking Brake Caliper Leaking

Today, as i had my car in the repair shop for a checkup i got a horrible message. The rear caliper/hand brake motor (?) is leaking brake fluid. Replacing this is close to 1500$ (I live in Norway) So my question is: Is there any way to stop the leak without replacing the whole thing? Also, i suspect the leak is minor as the brake fluid is almost on "max". So, if it doesn't really leak a whole lot, do i really need to do anything about it? I mean, if i have to refill the fluid container every six months its much cheaper.