Passat (B5) :: ABS Fault Codes - Transmission Control Module / Steering Angle Sensor
I have just replaced the abs ecu and have cleared the codes, thought all was gonna be good but now two code are still coming up they are:
01044 Transmission control module - incorrectly coded
00778 Steering angle sensor-G85
Passat (B5) :: ABS / ASR Fault Codes
Can dealership diagnostic tools read ABS/ASR fault codes, or if those codes are even stored?
View 1 RepliesPassat (B6) :: Sputtering And Fault Codes
Driving home car started sputtering like crazy. vag com'd it and this is what i got from the scan!
Friday,06,April,2012,16:16:02:36785
VCDS Version: Release 11.11.2 (x64)
Data version: 20120126
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Chassis Type: 3C0
Scan: 01 02 03 08 09 0F 15 16 17 19 1C 25 42 44 46 52 53 56 62 72
[Code] ....
Passat (B5) :: 2005 - Airbag Light On / No Fault Codes
I recently sent for a reset my airbag module, yes my car was in a collision, I replaced passenger airbag(only 1 airbag deployed). And reconnected the module. Using the VAG COM, I scanned the airbag module, shows no fault codes, but i still have a light.. now I'm thinking seatbelts and sensors maybe the problem. Where the sensors for a 2005 passat passenger dash airbag are located.
View 2 RepliesPassat (B6) :: 2006 - Check Engine Light Came On / Fault Codes?
I have a 2006 passat and the check engine light came on so I performed a scan, the results are below. fault codes... which ones would need to be repaired immediately?
VCDS Version: Release 805.1
Data version: 20080823
Tuesday,06,March,2012,18:12:35:26365
Chassis Type: 3C0
Scan: 01 02 03 08 09 15 16 17 19 1C 25 42 44 46 52 53 56 62 65 72
VIN: WVWAK73C86P106340 Mileage: 107910km/67052miles
00-Steering Angle Sensor -- Status: OK 0000
01-Engine -- Status: Malfunction 0010
[Code] ....
Passat (B5) :: Alarm Triggered When Trying To Start Car / Fault Codes 00928 And 01358
Ok in parking lot car is armed but driver side door is unlocked press the unlock on remote will not unlock the doors however I can pop the trunk with remote. Try to start car and alarm is triggered and car will not start. I have fault codes like 00928, 01358. Is there away to disable the entire alarm so I can start it and get home.
View 1 RepliesPassat (B6) :: 2006 3.6 4mo - Fault Codes For Catalyst System / AWD Controller And Haldex Pump
Ok, so I scanned a 2006 Passat 3.6 4mo. I got a fault for the catalyst system, a fault for the AWD controller, and a fault for the Haldex pump. I'm guessing the catalyst code is for the oxygen sensors? What should be my next course of action on the AWD stuff?
============================================
Address 01: Engine Labels: 03H-906-032-BLV.lbl
Part No SW: 03H 997 033 M HW: Hardware No
Component: P3.6-FSI-LEV2 G00 2370
Revision: --H11--- Serial number: VWZCZ000000000
Coding: 0000175
[Code] ....
Ford - Explorer :: 2004 - How To Clear Codes
Need to clear codes after doing a lot of work on this used Eddie Bauer With the 4.6 engine. Is there a procedure to clear the codes to get a new reading?
View 1 RepliesFord Wiring/Electrical :: Way To Clear OBD1 Codes?
E-150, 5.8/351
The Haynes manual says not to disconnect battery (for whatever amount of time) to clear codes because it also clears the keep alive memory forcing the computer to relearn.
What is the correct way to clear codes? The manual says talks about jumping the OBD connectors some way but I cannot tell what is showing in the picture.
Accent LC (2000-05) :: 2001 - Cannot Clear Codes P0123 And P1605
My 2001 Accent (Manual Tranny) with 95,000 miles needed the head rebuilt due to the timing belt slipping and making a mess of the valves. The car threw no codes before the mishap and ran perfectly but now shows the codes P0123 and P1605 after the rebuild. The shop that did the work said they spent 5 hrs trying to figure why these codes are showing. They swapped out the TPS which didn't work. I'm not sure if they swapped out the acceleration sensor. Anyway, since I picked up the car,it was idling low at about 500 RPm and fluctuating in neutral (remember its a manual. In the week that followed, the car wouldn't start a few times which I found out to be a loose negative terminal on the battery. Since I fixed that problem, the car idles at about 1,000 RPM when I start it but then jumps up to about 2,000 once it's warmed up or if I downshift and then throw it in neutral! And yes, the same 2 codes show up on my scanner.
View 3 RepliesMercury - Villager :: 1998 - Random Misfire Codes That Would Clear And Return
Yesterday, i changed the spark plugs, spark plug wires, mass air flow sensor, air filter and replaced the in and out take coolant lines in the throttle body.
Before yesterday, i got random misfire codes that would clear and return, i have no a/c, i believe the thermostat needs replacing as the van runs hot after a while of running and quickly when idling and the upper radiator hose is hot. The van's idle is rough to the point that some one else turned up the idle so it would stop stalling so frequently, especially in reverse. it stalls very very rarely now.
then a few days a go i got a knock sensor code that clears itself and then returns.
A friend changed the distributor cap, and noticed some melting and corrosion, hence the spark plug and wire change. this friend also pulled the wiring harness for the front 3 injectors while it was running. the one on the far right created no audible engine change (also this spark plug was immaculate compared to the others), so he said it is bad (or is my friend a moron?)i had also noticed a coolant hose that would spray coolant when really hot.
So yesterday i tackled the above. In the process of doing this i had to rip the other coolant hose to remove throttle body, i replaced these with a self cut piece of 1/2 heater hose. after removing throttle body, i realized i needed a gasket. so got one of those.
a few notes:i used antisieze lube and dielectric lube on spark plugs, thread and ceramic respectively. the mass air flow sensor is used.i cleaned the throttle valve with brake cleaner (non chlorinated) because it was nasty! i did not remove the cables attached to throttle body, just moved it out of the way while working.i hand tightened everything.there were 2 skinny hoses i disconnected, one with a metal tip that went in to the large rubber air intake hose, and one that ran into the throttle body (this hose ripped like a 1/4 inch off it seemed long enough, so i did not replace). i disconnected the large air intake hose at 3 spots with pipe clamps.i disconnected 3 wiring harnesses 2 at throttle body and 1 at mass air flow sensor
Now, it seems the van is running smoother while getting gas, but rougher when idling. What did i miss? what would be causing a rougher idle? I am now at work, i will not be home till around 9 cst. So I cannot check anything.the van did throw another code, but i have not checked it yet.
Lexus LS 2007+ :: Blisters In Clear Coat Of Steering Wheel?
I Have blisters in the clear coat of the steering wheel. Two have opened and the clear coat has started peeling off.
07 LS460
Golf/GTI VII :: Possible To Adjust Steering Assist - Increase Boost?
Is it possible to increase the steering boost, so that the wheel is easier to turn -- like with VAG-COM? I'm not a big fan of the heavy steering.
View 5 RepliesGolf/GTI VI :: 2010 - Power Steering Assist Failure Light Came On?
2010 Manual GTI (still barely under warranty)
I swapped to my winter wheels on Sunday, then the car sat garaged for two and half days. Went to start it this morning and just got a fast clicking, then the power steering light came on and went from yellow to red. Tried a couple of times and then it seems like the car lost power; clock reset, trip odometer reset, etc.
I'm going to check the fuses, but what the problem might be? I'd like to go to work today and in the weather we're having there's no way VW is sending a tow truck today.
Lexus LS 2007+ :: LS460 - How To Disable Steering Wheel Park Assist
Today my car came back from service, now when I reverse park I get this display where when you move the steering wheel you can choose the spot you park in. Before I was just happy reverse parking my car myself and get a different display showing me the back view with with green and red lines I think where the car is moving towards etc. I can't figure out how to disable this steering wheel park assist.
View 1 RepliesGolf IV R32 :: CEL For 9 Fault Codes
So i installed a USP test pipe and got Revo Stage 2 upgrade yesterday. I had no codes before the test pipe. I still have a CEL for 9 fault codes. 4 of which are all the o2 sensor codes. With all these codes my Traction Control light is on too. I think this may be a safety thing. I thought Stage 2 was supposed to get rid of the CEL. Especially for the 02 sensors in the rear.
View 6 RepliesGolf/GTI VI :: Fault Codes From ABS?
I coded a few things through VCDS (fogs as DRLs, turned up XDS, enabled TSC, etc.) and now I'm getting fault codes from ABS...
I did an autoscan before I started and there were no fault codes before.
Camry :: CV Axle Replacement - Intermittent Noise From Front Of Car More Clear On Turning Steering Wheel
I had my passenger side cv axle replaced two months ago 2002 camry xle 110k miles for the ABS broken ring. After that start to here a shuddering intermittent noise from the front of the car more clear on turning the steering wheel, sometimes I here a metal on metal noise on bumps, axle was a brand new one and a press garage pressed the bracket on it..
View 6 RepliesSubaru - Forester :: 2009 - Intermittent Power Steering Assist Failure During Low Speed Maneuvering
I just took my 2009 Subaru Forester (80,000 miles) in to a mechanic because it was having an intermittent power steering assist failure during low speed maneuvering (i.e., parking lot). This is always accompanied by a loud rhythmic whining form under the hood (kind of like a whaawhaawhaawhaa). By intermittent, I mean maybe 50% chance of it happening when I am maneuvering in a parking lot. By failure, I mean I can still turn the wheel but it's much harder. The mechanic diagnosed it as the following:
dry rot in drive belts, recommended replacement
leaky rack and pinion, recommended replacement
2 leaky front struts
I checked my power steering fluid before I brought it in and the level/color looks great. The mechanic said in addition to the leak that there's a little bit of a catch in the steering at a certain steering position when going faster, but I haven't noticed it myself. I have trusted this shop in the past and had good experiences, but there has been a lot of turnover lately, so I'm unsure of what to do. I went ahead and had them change the belts, but decided to wait on the rack/struts until I did more research/got a second opinion.