Prius (2010-12) :: Steering Angle Sensor Fault Code C1231
I have a fault wit the steering angle sensor, fault code c1231, I have replaced it twice now, the fault would go after installing recon steering angle sensor but would come back again after, not sure what the problem is, looks like they become faulty and dead.
View 1 RepliesPrius (2010-12) :: Steering Angle Sensor Fault Code C1231
I have a fault wit the steering angle sensor, fault code c1231, i have replaced it twice now, the fault would go after installing recon steering angle sensor but would come back again after, not sure what the problem is, looks like they become faulty and dead.
View 4 RepliesPassat (B6) :: 2.0T - How To Replace The Steering Angle Sensor
Just replaced the steering angle sensor on my Passat. Had a persistent fault that was causing a parking break warning light. I took pictures as I was putting it back together. [URL] .....
View 1 RepliesPassat (B7) :: Fault Code 03252 - Engine Control Module For HV Drive
I have a 2013 VW Passat TDI SE DSG and I was trying to do some tweaks. I found this fault code yesterday and cleared it. I scanned it again this morning and it popped up again. I searched and did not foud anything. No check engine light.
Saturday,16,November,2013,10:32:21:13221
VCDS -- Windows Based VAG/VAS Emulator
VCDS Version: Release 12.12.0 (x64)
Data version: 20130910
[Code] ....
Lexus GX 2004-09 :: Fault Codes P0037 And P0057 - Oxygen Sensor Heater Control Circuit Low
What can be done regarding these faults? P0037 and P0057
Description:
Oxygen Sensor Heater Control Circuit Low (Bank 1, Sensor 2)
Oxygen Sensor Heater Control Circuit Low (Bank 2, Sensor 2)
The catalytic converters have been removed but the fault was present before that anyway. All I want is the VSC function to work again and the lights to go off. I have heard you can put dummy sensors in.
Prius C :: Steering Rack Angle Fault After Alignment
I just had my Prius C in Alignment shop, and after alignment was done I got ABS light ON. We checked it and it says Steering Rack Angle Fault.
View 10 RepliesPassat (B6) :: 2008 - Steering Wheel Control Module Blown?
I have the below multi-function steering wheel installed on my 2008 Passat. The steering wheel came out of a 2010 CC and the buttons do not currently work.
Which steering wheel control module would I need and what is the price on that?
Besides the steering wheel control module and programming via VCDS/VAGCOM, do I need anything else for this to work?
Passat (B6) :: Cannot Get Steering Assist / ABS Fault Codes To Clear
I have followed the process for clearing and resetting the Steering Assist/ABS fault codes. I have done all the steps several times and cannot get the faults to clear, although the VAG-COM indicates all is green during the testing phase.
[URL].................... And the faults will not clear.
Here is the scan results, (non-fault sections removed):
VAG-COM Version: Release 704.1
Data version: 20070422
Sunday,03,June,2007,17:47:17:25986
Chassis Type: 3C0
Scan: 01 02 03 08 09 0F 15 16 17 19 1C 25 36 42 44 46 47 52 53 55 56 62 65 72 76
[Code] ....
Ford Aerostar :: SRS Fault Codes - Airbag Module Failed
My van is spouting SRS fault codes 1-3 and 5-1. I had my shop run a diagnosis and it appears the module has failed. I'm having trouble tracking down a replacement. The Module on my van is Ford# F5AF-14BO56-AA. I see modules with -AD or -BD, but none that match this number perfectly. I also see lots of modules for related Ford vehicles from the same era. Looking for a ford parts number reference sheet that will indicate on what vehicles this module was used or if there is any chance that related modules are compatible?
View 14 RepliesSonata NF (2006-10) :: Where Is Steering Angle Sensor Located
I know it's on the steering column but is it down near the floor or on the engine compartment side?
View 4 RepliesPhaeton :: 2006 - Steering Wheel Angle Sensor
So the saga of getting my 2006 Phaeton fixed after an interaction with a deer continues ..... The car has been put back together and fixed, but now there is a new warning light linked to the steering wheel angle sensor.
View 10 RepliesTouareg :: Airbag Fault Code / ABS Control Module
I recently received an airbag fault light so I figured that I would scan the module for error codes. This is what I came up with:
Control Module Part Number: 3D0 909 601 C
Component and/or Version: 05 Airbag 8.4E++H01 0352
Software Coding: 0012341
Work Shop Code: WSC 31414
Additional Info: 7L0959339B BF-Gewichtsens. 005 0006
Additional Info: Geraet 00000
2 Faults Found:
01217 - Side Airbag Igniter: Driver Side (N199)
001 - Upper Limit Exceeded - Intermittent
01316 - ABS Control Module
004 - No Signal/Communication - Intermittent
Has scanned the car while had the airbag fault present and if so, is this the usual harness that needs to be changed?
Passat (B5) :: O2 Sensor Codes - Evaporative Emission Control System
We are selling the girlfriends 01 Passat. I pulled the codes tonight for a long standing check engine light knowing it had one of the 02 sensors bad. Here are the three codes I received from the scanner:
P0130 - 02 Sensor Circuit Malfunction (Bank I Sensor 1)
P0455 - Evaporative emission control leak detected (large)
P0441 Evaporative Emission Control System Incorrect Purge Flow
So is it one thing causing all three or are there common things to look at. We can't really afford to go replacing all the emission system sensors and hoses etc. in hopes of finding the right piece. Gas cap is screwed on tight and codes were cleared a couple times to make sure.
Golf IV R32 :: Fault Code P0606 - Powertrain / Engine Control Module?
The code the R threw was p0606 which is the Powertrain/ Engine control module? Where these components are in my R? Or how I can go about trouble shooting this problem?
View 9 RepliesGolf/GTI VI :: P1628 - Steering Angle Sensor Code / 18036 - Powertrain Data Bus Comes On
2012 GTI. DSG My airbag was blows, so I replaced it. Now im getting the following code.
18036 - Powertrain Data Bus
P1628 - 000 - Missing Message from Steering Angle Sensor
Can the sensor go bad after the airbag was blown? All the steering wheel controls still work.
Golf IV / Jetta IV :: 5 Engine Fault Codes - Cam Position Sensor / Knock Sensor / Secondary Injection Pump And Mass Air Flow
I recently picked up a 2000 jetta vr6 for a very good price its a glx I have owned a vr6 before and done timing chains myself on it this one is a glx , I am having 5 fault engine codes on my vagcom they are cam position sensor , knock sensor, secondary injection pump, and mass air flow it ran fine 100 miles yesterday this morning the epc came on then went off and ran bad can these codes all be related or do I have to replace each sensor individually..
View 9 RepliesGTI 337/20th Anniversary :: Code 00778 - Steering Angle Sensor / No Or Incorrect Basic Settings
I put in a new sensor to stop the problem but now I have the code 00778 which is steering angle sensor and then says 005 no or incorrect basic settings/adaption. I went through the Ross-Tech site to reset the code in group 60 and activate the basic settings, but I am then told that group 060 is not available. I have tried to set the steering wheel angle straight but the angle still says its at 349.47*. My car is a 2004 Jetta GLI 1.8T.
View 4 RepliesCamry :: Error Codes - Evaporative Emissions Control System Vent Control Circuit Fault
My check engine light has came on and I received these error codes
PO441 : Evaporative emissions control system incorrect purge flow.
PO 455 : Evaporative emissions control system pressure leak-large leak.
PO 446 : Evaporative emissions control system vent control circuit fault.
Also only my driver side fan is working, may be separate issue?
Ford Wiring/Electrical :: 2014 F150 - Starting System Fault / Body Control Module Malfunctioned
I own a 2014 F-150 XLT 3.5 L 6 cyl Twin. Saturday afternoon I tried to start the truck once and it didn't start like it normally does. It started on the second try, but the A/C didn't work and I got a "Starting System Fault" warning on my screen. When I shut the truck off, it would not start at all. All the lights and gauges worked, just no start.
Had to tow it to Ford Dealer, where the service department had already closed for the day (of course). Today it was determined by the service department that the Body Control Module had malfunctioned. I was told that the tech tapped on the control module and the truck started. Now waiting two days for a replacement part to come in. Luckily, I'm just under 36K miles and three years. Is this a common occurrence?