Golf VI R :: New Clutch - 1st Gear Stuck
Car: 2012 Mk6 Golf R
Mileage: 43,000 km
Software: UM stage 2 loaded
Related mods:
- diesel geek short shifter
- Emmanuel design, Sachs SRE stage 2 SMf clutch kit
- Tyrol sport deadest rigid collar kit (probably not related)
Background info:
Clutch installed at 40k km.
0-500km stop and go traffic
500-505km punched it bc a 350Z pissed me off*
506-1200km highway and not very aggressive twisters
1200-3000km hwy and city mix
First 0-500km I babied the clutch. No issue
501-505km I punched it a bit hard. Felt great. No issue
506-1200km hwy there, no issue. Closer to the 1200km mark the issue surfaced
1200-3000km was able to repeat the issue and adjusted diesel geek ss and re-bled the clutch in attempt to resolve it
Issue:
- from dead stop, 1st gear gets locked in at 2-4k rpm
- either I rev up beyond 4k, drop below 2k rpm to unlock it
- if I man handle n yank it out of 1st, gears grind
- only happens when the car is fully warmed up and fully running at optimal temperature for at least 10-15 minutes
- diesel geek ss readjustment
- re-bled the clutch (no topping off the clutch lines)
Issue was improved, however, I'm experiencing this locking issue again. Less frequent and less predictable. Attempted to replicate the issue, only happens if it's stop and go traffic-jam speed. Was unable to focus on an rpm range.
Golf IV / Jetta IV :: Stalls Out In Stop And Go Traffic / Bang And Clutch Pedal Drops To The Floor
I have a 2005 VW jetta 2.0 engine 5 speed. Just replaced right control arm spark plugs wires and coil pack. I had a misfire only when it rained and it got rid of it! Driving home in stop and go traffic and My car stalls out a hear a bang and my clutch pedal drops to the floor. I had noticed some fluid loss but nothing was low I checked everything before I left work. I finally get it towed but I can not shift to first I can shift to 2 3 4 5 and reverse. I was in first when it stalled out during stop and go traffic while it was in first gear and i had the clutch pressed in. Everything Ive google says it is more than likely the Slave cylinder that is right below the air box. I found some that said it could be the release bearing in the gearbox for the tranny...
View 4 RepliesGolf VI R :: Clutch Pedal Stuck To The Floor On Several Occasions
So over the weekend my clutch pedal stuck to the floor 2 times and would not come all the way up on several occasions. It has since then stopped doing it. I am wondering if I should bleed my clutch or not. Flush and change fluid?
Just concerned it may turn worse.
Golf IV R32 :: Stalled When Put Car In Neutral And Took Foot Off The Clutch / Now Stuck Is Reverse
I came home last night and rolled into the driveway. With the car in neutral I took my foot off the clutch and the car stalled. I get in the car this morning to go to work, and it's still happening. I put it in reverse to see if it will drive.....and now it's stuck in reverse.
I can't get it into any other gear or neutral..........even when the car is off. I've unattached the linkage, and the shift knob moves freely.....so I don't think it's that. I found these old threads (one even mine)
[URL] ...
[URL] ....
[URL] .....
So I'm lead to believe that the master/slave cylinder is acting up again. Also, how can I get it into neutral so I can at least get it towed and stop blocking my driveway?
Golf IV / Jetta IV :: 2001 Gti VR6 Stuck In Reverse / Clutch Won't Fully Disengage
My 01 GTi (12v VR6) was having some trouble shifting into, and out of, first and reverse so after a bit of research I decided to try adjusting the shift linkage as it seemed like a possible easy fix. After doing that I tried backing it up in the driveway and after a couple of shifts to different gears it ended up getting stuck in reverse. When I pushed in the clutch pedal to let it roll forward I noted that it seemed to be resisting rolling forward despite the steep incline. Once it reached a less steep incline it stopped rolling forward completely, so I'm thinking that it probably won't come out of gear because the clutch won't disengage all the way.
I've done some searching around and from what I've read so far it sounds like it could be a worn or damaged clutch fork, the hydraulic lines, master or slave cylinder, or even a broken clutch plate. What I don't want to do is pull the transmission and clutch, only to find that it was something much easier to fix.
Golf IV / Jetta IV :: Clutch Pedal Stuck To Floor With Fluid Underneath Car
I have a 2003 Jetta GLI. Thus morning driving into work my clutch pedal stuck to the floor. I was able to pull it back it and make it to work, but when i got to work i noticed fluid dripping from underneath my car.
View 4 RepliesGolf IV / Jetta IV :: 1998 - Clutch Engages Lower To The Floor / Shifter Stuck In Gear
98 Jetta TDI hydraulic system ... We just received this vehicle from my mother in law, who is not driving any more. It's a cream puff--79,000 miles, beautiful condition. Problem is the clutch engages lower and lower to the floor, and eventually the shifter gets stuck in gear. The brake pedal slowly sinks to the floor when at stops on hills. Our mechanic tells us these two are connected because both the clutch and brake run off the same hydraulic system.
1st time he said the fluid was filthy, and he emptied the system and put in clean fluid. Worked for a little while and then we were back where we started. Second time he replaced a couple parts on the clutch, replaced this fluid, and this time it ran like a dream for a little over a month. Then the problem just returned. Again he says the fluid is filthy, and now we are looking at replacing the master cylinder and again changing the fluid. The theory behind why this is happening is that my mother in law let the car sit for half a year before passing it on to us. She didn't do much driving the 6 months before that either. I've done research, and this doesn't appear to be a common problem by any means on these cars.
Golf/GTI VI :: Clutch Pedal Is Losing Pressure / Stuck At The Bottom And Refuses To Bounce Back
Just a heads up to all MKIV GTI owners out there, new and old. If you feel like the tension on your clutch pedal is deteriorating get it checked earlier rather than later. Because if the slave cylinder malfunctions and leaks you will be faced with a big repair bill due to the fact that the slave cylinder is located inside the tranny. Secondly because of this design, which I think is very stupid, it leaks onto the clutch assembly and can get on your clutch plate. At that point you should replace the clutch plate to prevent any further damage that might be caused by slippage. The clutch plate should not come in contact with any fluids or it will compromise the functionality.
View 2 RepliesMazda - B2300 :: 2004 - Stalls When Push In Clutch
I have a 2004 mazda b2300 4cyl 5 speed that wants to stall on me sometimes when I engage the clutch and all most come to a complete stop. It does not happen every time i do this, but some of the time. I am able to instantly restart the truck and drive just fine. I am just confused at what might cause this. I did a tune up to it this weekend, and the cap from the clutch fluid did come off, I don't know if this would have anything to do with it. The truck runs great, just wants to stall some times.
View 19 RepliesPassat (B5) :: 1997 VR6 Stalls Or Stutters Hard After Clutch Drop
Just started doing it last week some time and only happens when I am launching it from stop or grabbing gears hard.
This is a little idea on whats happening.. At stop light next to some random ricer.. maintaining 2500 rpms on tach
drop (stage 4) clutch on green
Car squeaks and dies out like a stall and dash lights flash as well as lights on controll/radio area (around abs light) radio shuts off like a stall.
Accent LC (2000-05) :: Stalls In Neutral When Clutch Pedal Released
I have an 00 Accent 1.5 liter 5 speed with about 192000 miles on it. I have put about a tank of gas through it since I've owned it, so I can't give a lot of background on it. When I got it the previous owner told me it was popping out of fifth gear and the clutch fluid leaked.
Upon driving it around a while I noticed it would pop out of fifth and third gears almost at random, but seemed to happen more when I applied throttle. I assumed it was an issue with the shifter not fully engaging the gears, and checked out the bushings under the hood and in the console. All looked good, and I didn't see any extra play.
I drove the car for about 30 miles straight and had to downshift and wasn't able to get the car to go into any gear but fifth. I was moving about 20 mph when this occurred. I was able to limp along to a parking lot where I let the car sit for about ten min and I shifted through the gears when stopped. I headed back home with this problem throughout the trip. There is a sound that happens on occasion (that stops when I press the clutch pedal) that sounds like a bad bearing in the clutch area.
When I'm stopped with the car in neutral and I release the clutch the car stalls like it's in gear. I was able to get the car to move some, but it really doesn't want to it acts like there is something jammed in the gears and popped really loud when I backed it up.
There is fluid for the master cylinder, and I can see the slave cylinder moving when the pedal is pressed. I jacked it up and removed the plug to check for gear oil, and it came pouring out, so I think it has fluid in the gearbox. I'm pretty sure it needs a clutch at the least. I think there may be some internal damage in the tranny, and I'm only into the car for the time it took to power wash a house and don't want to get involved in a big mess.
Gti - Volkswagen :: Stalls When Turning Abruptly Or When Initiating A Stop With Clutch Depressed
My son's 1988 MK2 Golf GTI recently began a most curious random rough idle, occasionally to a stall, especially when turning abruptly, or when initiating a stop with the clutch depressed, and now always when turning at low speeds in combination with brake application. This only occurs when the engine is warm. The braking clue first led me to investigate the brake vacuum booster as they will cause that symptom when they fail internally, but if they fail, the sudden low , rough idle symptom is repeatable. This is not the case. Sitting in the driveway I can depress the brakes firmly with no change in engine rpm. Idle stays steady and normal. So I checked carefully for vacuum leaks, found none. Checked all the fuel system sensors and idle speed regulators, all are in order. New battery, good output from the alternator, ignition timing strobe is steady and bright. All the air intake rubber is like new. The in-tank fuel transfer pump works. The high pressure external fuel pump works.
View 8 RepliesCamry :: 2003 - Clutch Pedal Stuck
My wife has a 2003 Camry that we had to replace the clutch last year. Now her clutch pedal goes to the floor and does not return.
View 2 RepliesVolvo :: AC Compressor Clutch Will Not Engage - Fan Stuck
if the fan doesn't work, could this make the AC compressor clutch not engage? I think the fan is burned out because it doesn't spin at all, and only moves with a lot of effort. If the fan circuit is open, will this cause the Compressor to not work as well? the car is a 1991 740 GL. 2.3L engine, non turbo.
View 3 RepliesElantra XD (2001-06) :: Clutch Fork Stuck / Does Not Release
2002 Elantra
Replaced new clutch disc and new pressure plate.
Without turning on the engine, the clutch pedal seems to get harder to press, until it can't be pressed down anymore. The pedal can't be pressed down.
Clutch fork lever does not release.
Passat (B5) :: 1999 - Clutch Pedal Would Not Come Up Off The Floor / Stuck
Facts: 1999 Vw passat 1.8t
1 year ago, clutch pedal would not come up off the floor, no life in the pedal.
Problem: Clutch master cylinder, replaced.
6 months ago, clutch finally went bad. Took car to clutch shop, replaced clutch kit(found out after i payed that they only turned the dual-mass flywheel... ). Get car from clutch shop, the clutch pedal came up only 2-3 inches off the floor by itself but you could lift the pedal with your hand or foot, and it would come back up all the way, but it was life-less. It was not pulling fluid in. It was catching extremely low. I called the shop, they said that it was just because it was a new clutch and it would get better. I didn't believe them.
Two days ago, I got into my car and couldn't get it into gear. Clutch pedal would go down with the same amount of force as before. Took it back to the clutch shop and explained the history with the clutch master and then them doing the clutch kit. They said it wasn't bleeding properly and they're not sure if its going to have problems again. Car is working now, but I am concerned that it will have similar problems again.
The tech who fixed it said he pumped fluid into it extremely hard, and that's what made the pedal come up all the way (no longer stops 2 inches off the floor) and its going into gear just fine now. What the problem might have been? Block in the hydraulic lines? If this is the case, does forcing fluid through it fix it?
GTI 337/20th Anniversary :: Clutch Stuck To The Floor On The Highway
50k Miles on my clutch. Was driving a couple weeks ago on the highway and clutch stuck to the floor. At first I thought it was my Slave cylinder. Got the trans out this weekend to find the mess (below) inside my bell housing. Obviously need a new clutch now and will still replace the slave while I am in there.
Cars setup is around 375ish whp. I know I could spend 1300 bucks and call it a day for a clutch master or south bend but was seeing if there is a cheaper alternative.
Also If I were to buy an OEM clutch or an upgraded one that was not rated for up to 400~whp would it drive and pull the same as a fully upgraded one just not last as long?
6 Speed ...
GTI 337/20th Anniversary :: Clutch Pedal Stuck In Place - Could Not Put It In Gear
So last night I was driving home from work, and at a red light while i was waiting to go i had my clutch down when light turned green i tried to go and noticed i could not put it in gear and that my clutch pedal was stuck in place. i didn't know what to do so I checked my shifter plate everything looked fine so went to look at the pedal and i pulled it forward and it came lose. I started it up everything was fine and back to order. This morning going to work same thing happened again, I don't know what is going on and what could be the cause?
View 5 RepliesElantra XD (2001-06) :: 2002 - Clutch Stays Stuck Engaged
My 02 elantra gls 5 speed clutch has gotten stuck engaged for about the third time now. First time was right after I bought the car i noticed the clutch would slip randomly for no reason. At first i thought the clutch must need replaced, but then other times I couldn't make it slip if i tried by going up steep hills with car full of people and shifting too soon on purpose and punching gas....no slip. So anyways i replaced the slave cylinder, and all was good till one day my wife calls me up stranded and says clutch pedal is rock hard and none of the gears will engage. so i tow the car home and fiddle around and realized the slave cylinder (brand new one) was stuck out. I opened the bleeder and it returned without me having to push on it or anything. i then bled the system thoroughly. So months have gone by and the slave cylinder got stuck out again, and again it was a simple turn of the bleeder valve and it went back and works fine. just curious as to how i can fix this problem permanently since its irritating and seems to be reoccurring. do i need to replace the master cylinder as well or did i buy a bad slave cylinder?
View 6 Replies