GTI 337/20th Anniversary :: Clutch Pedal Would Stick At 3/4 Of The Way Up
I recently got the GTI 1.8L 337 with 64,000 on it. It had been sitting, with daily start-ups, for about 8 months until the ALT was replaced. I've been driving it for a month with no problems until last week. At first I noticed the clutch pedal would pause on the way up for a split second then tap the bottom of my shoe. I thought maybe it needed adjustment but nothing serious. A few days ago the pedal would stick at 3/4 of the way up, and stay there most of the time unless I raised it with my foot, till the car warmed up a bit. Yesterday and today the pedal started to stick 1/4 of the way up, unless raised with my foot, at the morning start-up and will only come up 3/4 when warm. It also wont go into reverse at initial start-up until it gets really warmed up, shifting into other gears is fine. I've had no problems or real sounds shifting into any other gears, though out of 1st has been a little jumpy.
View 3 RepliesGTI 337/20th Anniversary :: Clutch Pedal Went Soft?
We were headed home the clutch pedal went soft... Ok, I thought it's either the clutch master or slave. I get it home and replace the master and after bleeding I had good pedal feel.
Great I thought, I got lucky and it was only the master. Drive it around for a bit and get on the highway and just as I was about to downshift the pedal went flat to the floor again.
Well after pumping the pedal until it had good feel again I got it home and bleed it a couple more times just to make sure I got all the air out. Drove it again. Same thing, after a little while the pedal gets soft again.
Now before I go and replace the slave is it possible I have a faulty master? Having issues after replacing the master?
GTI 337/20th Anniversary :: Clutch Stuck To The Floor On The Highway
50k Miles on my clutch. Was driving a couple weeks ago on the highway and clutch stuck to the floor. At first I thought it was my Slave cylinder. Got the trans out this weekend to find the mess (below) inside my bell housing. Obviously need a new clutch now and will still replace the slave while I am in there.
Cars setup is around 375ish whp. I know I could spend 1300 bucks and call it a day for a clutch master or south bend but was seeing if there is a cheaper alternative.
Also If I were to buy an OEM clutch or an upgraded one that was not rated for up to 400~whp would it drive and pull the same as a fully upgraded one just not last as long?
6 Speed ...
GTI 337/20th Anniversary :: Clutch Pedal Trim Is Coming Off?
Noticed the other day my clutch pedal trim is coming off... What did you do to fix it?
View 8 RepliesGTI 337/20th Anniversary :: Clutch Pedal Is Soft At First And Then Gets Harder
I keep finding air every time i bleed my clutch. I am not losing fluid but i can not figure out whats causing my problems. The pedal is soft at first and then gets harder and it sometimes needs pumped before i change gears or to even get into gear. I am afraid its the slave but i also just may have air in the system.
View 8 RepliesGTI 337/20th Anniversary :: Clutch Replaced - No Pressure In Pedal
I just replaced my clutch and have put everything back together, and bled my clutch line, but I have absolutely no pressure still in my pedal. I read that u need to make sure your brake fluid reservoir is filled to the max, but following the clutch line, I dont see it going to the reservoir? I also read that the master cylinder is behind the clutch pedal, does the master cylinder hold any fluid that maybe I lost during the bleeding? I'm at a loss right now.
View 12 RepliesGTI 337/20th Anniversary :: Clutch Pedal Dropped To The Floor At The Stop
Coming to a stop, clutch pedal just lost all pressure. I can bring it back up, but even the slightest touch will send it to the floor again. I get the brake warning light on the dash. What could be causing this?
View 7 RepliesGTI 337/20th Anniversary :: 2003 - Zero Resistance When Clutch Pedal Pushed
My clutch has been feeling very strange lately, and has had a mind of its own. I have looked underneath myself, and have even taken it in to two transmission speacialists and they can't figure it out. The master cylinder isn't leaking, and the slave cylinder is fine as well.
Here's what is going on with my clutch...
- I will push in the pedal, and there will be ZERO resistance until about 1 inch from hitting the floor, then all the pressure is there, and I am able to shift. However, sometimes I won't even be able to put it into gear because the clutch won't engage.
- Then I will pump the pedal, and slowly I will gain a little more room on the draw of the clutch, and it will feel fine. All the way to the point where a few days later it will be driving like new.
- Then it will start feeling funky again a few days later and the cycle starts over.
I drive a 2003 GTI 20th AE.
GTI 337/20th Anniversary :: Clutch Pedal Goes From Being Soft To Very Hard When Close To Disengaging
I have an Imola 20th and recently i have been having some problems with my clutch. The pedal goes from being soft to very hard when its close to disengaging. It also engages very heavily when I go to let it out. This only started happening recently when temperatures started to drop if this has any effect on a clutch. Also, I replaced a shift fork two months ago and was curious if there was possibly anything going on with seals around the slave cylinder.
View 2 RepliesGTI 337/20th Anniversary :: Clutch Won't Return - Could Not Put It Into Gear
Today I went to start my car and let it warm up and everything worked fine and it started regularly but when I went to go drive the car and put the clutch in the pedal didn't return and I could not put it into gear, need to identify the problem.
View 4 RepliesGTI 337/20th Anniversary :: 2004 - Clutch Won't Go Into Any Gear
My wife was driving home and was exiting the freeway, downshifted and then no response from the clutch or gearbox. It would move left to right but not go into any gear with the car on. No real pressure in the clutch pedal either. With the car off you are able to find all the gears but when you start the car in gear with the clutch down it just jumps forward and dies. No smoke or burning smells either way and the pedal does come up by itself. Pushed the car into the driveway and its goin to the shop tomorrow morning.
With the search button so far: master/ slave cylinder, full clutch problem, air in brake/clutch lines, shifter linkage bracket
I don't think it's the slave cylinder as the pedal is NOT stuck to the floor, but I am not handy with cars, only motorcycles. First thing I checked was the linkage bracket, which seemed to be fine and as I stated, I was able to get in gear while car was off. Brake fluid was almost full but i know that doesnt rule out air in the lines.
GTI 337/20th Anniversary :: Clutch Grinding When Go Into Second Gear
So I am pretty sure its my clutch that is the problem, here's what happens: When I go into second gear, it doesn't really grind.. but its tough to get it into gear and its only with second gear. sometimes it will go right in and others i have to double clutch. when i double clutch it goes in smooth every time. now I don't think it would be syncros because I am pretty sure if it was that it would do it every time I shift? It only does it while its cold or hasn't been drove in awhile.. but after i drive it around its fine so I am pretty sure its the clutch. Second thing, what is an upgraded clutch that is good for these 6 speed transmissions?
View 2 RepliesGTI 337/20th Anniversary :: No Clutch When Going To Put Car In Gear / Just Grinding
I just put a stage 1 clutch in my 20th anniversary. When i was taking the transmission out, i dropped the hydraulic clutch line and all of the fluid spilled out. I got the whole thing done, and bled the clutch line and topped off the reservoir. I started the car and the clutch pedal had, what felt like the right amount of pressure. More than the stock, but not significantly. When i went to put it in gear, its like there is no clutch, just grinding and it doesn't go in to anywhere. I can cycle through the gears with the car off and like i said, the clutch has the right pressure and everything.
View 10 RepliesGTI 337/20th Anniversary :: Barely Able To Move The Shifter / Clutch Pedal Fell To Floor
The transmission is a Six-speed MQ350 transmission in an MKIV 337 GTI.
I was driving last week and ran over a large snow chunk, heard it hit the underside of my car. A mile down the road my foot is resting on the clutch pedal at a stop light, and the clutch slowly went to the floor. It was still drivable, barely. The clutch came about an inch off the floorboard, but still caught. So i pull into the parking lot ahead of me, and was barely able to move the shifter left to right nor would the shifter go into gear. There were no fluids coming from under the car, nor could i see anything that looked wrong. I turned off, back on again. nothing. I then pulled the clutch pedal up from the floor and it went back to normal. Everything seems normal now, but the shifter seemed a little sticky yesterday from left to right.
GTI 337/20th Anniversary :: Clutch Started Acting Strange / Pedal Felt Softer
Recently my clutch started acting strange, the pedal felt softer and eventually after I pressed it in it stayed on the floor. After pumping it, everything went back to normal. Next day, still same thing, no pressure in the clutch pedal. I checked the brake fluid and it's full. There is also no sign of any leak. Took the car to the mechanic, he recommended changing the master cylinder. I changed it but still nothing. I tried bleeding the slave but every time I bleed it, it has air in it. So I'm stuck and don't know what should I do next. I think it might be my slave cylinder but I don't have a place or tools to do it myself. I'm pretty sure the entire tranny needs to be pulled out to remove the cylinder. I also read that most people change the clutch when they replace the slave.
View 10 RepliesGTI 337/20th Anniversary :: Accidently Went Past 3rd Gear, Clutch Went Out
I recently was driving home from a buddy's house, when at the light i go to put the car in 1st gear and it was way harder than normal. I kept driving just to try and get home but it was so bad that i never went past 3rd gear.. I'm pretty sure the clutch went out, since it was extremely hard to get the clutch to engage to get it from gear to gear, and i basically have to turn the car off to get it to stop so.....
I'm pretty new too the vw game, and don't know of any good companies as far as clutch kits. Im looking to buy somethings either oem like or a little better but with the same feel. also, just a Pressure plate and clutch. I doubt the flywheel is damaged.
GTI 337/20th Anniversary :: Clutch Disengagement - Cannot Go Into Gear While Driving
So after replacing my shift forks in my 20th, installing a new clutchmasters fx100 clutch kit with a LWFW I've become a victim of the typical clutch disengagement issue.
In a nut shell car doesn't go into gear while the car is running. System is fully bled with no leaks and a brand new slave installed supplied by CM.
My understanding is the early FML code o2ms in the 20ths can not make use of the NLS shim kit and a stainless line is not a 100% fix.
Who's solved their disengagement issues and how?
GTI 337/20th Anniversary :: Clutch Is Beginning To Slip In 6th Gear
So I was on the free way in 6th gear and decided to get on it, the rpm's shot up and I barely picked up speed. It's only a slight clutch slip tho only really noticeable in 6th gear so I was wondering what clutch I should go with because I was planning on going BT eventually.
View 3 RepliesGTI 337/20th Anniversary :: Clutch Pedal Operates Properly But Squeaking Noise Coming Within Cabin
So your clutch pedal operates properly, the clutch engages with no issues, but this annoying squeak, snap, crackle, and pop noise keeps coming from the clutch pedal within the cabin.
Could it be your clutch master cylinder? CMC is not leaking in the engine bay and the driver footwell. Not the CMC.
Could it be your clutch switch that's used to control revs and cruise control? Removed it and clutch pedal still made noises when pressing and releasing the pedal. Not the CS.
Could it be the over-center spring that sits behind the clutch pedal assembly? How could it be? It's just a spring. Springs that compress in that orientation don't make snap, crackle, and pop noises.
What most people fail to realize is the noise is coming from the pedal assembly, but it's not the pedal structure or the pedal. It's the pivot point where it mates with the clutch pedal mounting bracket. At the pivot point are two bushings (one on each side of the pedal structure) that wears out over time creating these noises.
Please look up the part number for these bushings. They look like the following at this link but these are aftermarket upgrades for BMW's.[URL] ....