GTI 337/20th Anniversary :: Slight Grinding Noise In Neutral - Clutch Went Out
I was driving down the street and i noticed i couldnt get it in first gear, almost like a wall blocking it. and then i put it into 2nd gear and i started rolling... i turned my car off and when i started it back up, it had a slight grinding noise (in neutral). i put it in first gear, took out the clutch and i wasnt going anywhere... same with 2nd gear...
so i towed my car to the shop, they said my clutch went out and i "lost first and REVERSE gear".... is that possible?!
GTI 337/20th Anniversary :: Clutch Not Working / Grinding Type Noise And Doesn't Go Into Gear
So I picked up a 20th today. The clutch has 30k on it its an oem luk. Drove fine most of the ride home then i went to shift and it wouldn't grab. Got it towed home. trans goes into all gears fine. When you put it in first and try to go it starts to roll but just makes a grinding type noise and doesnt go into gear. I didn't hear any chatter until maybe 10 miles before this happened. I still have pressure in the clutch pedal as well. when the car is in neutral running there isnt any noise which makes me think it isnt the throw out bearing.
View 2 RepliesGTI 337/20th Anniversary :: Clutch Grinding When Go Into Second Gear
So I am pretty sure its my clutch that is the problem, here's what happens: When I go into second gear, it doesn't really grind.. but its tough to get it into gear and its only with second gear. sometimes it will go right in and others i have to double clutch. when i double clutch it goes in smooth every time. now I don't think it would be syncros because I am pretty sure if it was that it would do it every time I shift? It only does it while its cold or hasn't been drove in awhile.. but after i drive it around its fine so I am pretty sure its the clutch. Second thing, what is an upgraded clutch that is good for these 6 speed transmissions?
View 2 RepliesGTI 337/20th Anniversary :: No Clutch When Going To Put Car In Gear / Just Grinding
I just put a stage 1 clutch in my 20th anniversary. When i was taking the transmission out, i dropped the hydraulic clutch line and all of the fluid spilled out. I got the whole thing done, and bled the clutch line and topped off the reservoir. I started the car and the clutch pedal had, what felt like the right amount of pressure. More than the stock, but not significantly. When i went to put it in gear, its like there is no clutch, just grinding and it doesn't go in to anywhere. I can cycle through the gears with the car off and like i said, the clutch has the right pressure and everything.
View 10 RepliesGTI 337/20th Anniversary :: 2004 - Grinding / Rubbing Noise When In 3rd Gear
Just recently bought a 04 gli. When I shift in to 3rd and let off the gas there is a weird grinding rubbing like noise. It only makes the noise when it's in 3rd gear...
View 3 RepliesGTI 337/20th Anniversary :: Loud Clunking Noise When Release The Clutch
Car was great this weekend, then on saturday, every time I shift my car clunks right near the tranny when I release the clutch. Its a loud noise. Clutch was done around 2500 miles ago. South Bend stg 1 with a LWFW (I know, wish I stayed with a DM). And if I drive in first and second and come off the gas without shifting, it also knocks once really loud. It isn't a back fire or anything it almost feels like the dogbone mount is bad? Also, over 4000 rpm my car sounds deeper sounding than before.
View 7 RepliesGTI 337/20th Anniversary :: Grinding Noise While Engine Braking On 2004 Jetta GLI V6
2004 Jetta GLI V6 24v 6 speed ... This started a few years ago, but it was happening in 3rd gear only -- therefore I avoided engine braking in 3rd gear all along. The noise was a pretty loud, noticeable grinding/spinning noise. 3rd gear while accelerating or maintaining gas worked and still works perfectly, smooth as can be.
Somewhat recently (6mo-1yr ago) all the other 5 gears started making this grinding noise, some more than others. 1st gear I don't really know because I don't engine brake in 1st. However, 2nd, 3rd, 4th, 5th and 6th (barely noticeable but still there) all make the noise. I now of course avoid all engine braking, however even the transitional steps between gears can be heard sometimes ... unless I perfectly match the RPM etc, but I'm just trying to get to work and back here ...
The car is still quite drivable, but with a major obstacle (pain in the ass) and a new clutch is probably around the corner -- I have 107K on it now. However ... a few years ago when it had 26K on it .. it didn't need a new clutch yet 3rd was still making that noise.
GTI 337/20th Anniversary :: Clicking / Grinding And Creaking Noise When Turn Wheel
I've just started noticing a "clicking/ grinding/ creaking" when I turn my wheel. It makes the noise if I'm parked, or driving slowly. I can feel it in the steering wheel, and hear it in the cabin, but can't hear anything when I'm under the car.
It sounds like 'two pieces of rubber binding on each other', is the best I can describe it. I THINK its coming from the driver's side. I've considered: strut mounts shifting, CV joints, something in the steering column, Tie rods, power steering pump...
Everything is tight on the wheel when I try to move it by hand (on jacks), and no rips/ tears in any boots.
GTI 337/20th Anniversary :: Grinding / Squealing Noise When Moving Backwards / In Reverse
So I put in new rotors and pads and everytime the car is backing up I get a weird grinding or squealing noise. I've driven the cars for hundreds of miles and this still happens. This only happens when going backwards. Anything to try???
View 4 RepliesGTI 337/20th Anniversary :: Grinding Or Rattling Noise At Start Up That Stops After Few Seconds - Code PO411?
I have the po411 code, not sure which problem it is but when I first start the car it sounds awful like almost a grinding or rattling noise then stops after a few seconds.
View 3 RepliesGTI 337/20th Anniversary :: Clutch Pedal Operates Properly But Squeaking Noise Coming Within Cabin
So your clutch pedal operates properly, the clutch engages with no issues, but this annoying squeak, snap, crackle, and pop noise keeps coming from the clutch pedal within the cabin.
Could it be your clutch master cylinder? CMC is not leaking in the engine bay and the driver footwell. Not the CMC.
Could it be your clutch switch that's used to control revs and cruise control? Removed it and clutch pedal still made noises when pressing and releasing the pedal. Not the CS.
Could it be the over-center spring that sits behind the clutch pedal assembly? How could it be? It's just a spring. Springs that compress in that orientation don't make snap, crackle, and pop noises.
What most people fail to realize is the noise is coming from the pedal assembly, but it's not the pedal structure or the pedal. It's the pivot point where it mates with the clutch pedal mounting bracket. At the pivot point are two bushings (one on each side of the pedal structure) that wears out over time creating these noises.
Please look up the part number for these bushings. They look like the following at this link but these are aftermarket upgrades for BMW's.[URL] ....
Ford Transmission :: 2001 F150 Truck Shudders When Letting Out The Clutch
I have a 2001 F-150 4.2L 2WD LS with 102k miles. At 95k miles, the clutch slave cylinder started leaking fluid. So, I had my local garage replace it. And while they were at it, put in a new clutch. That is when the trouble started.
I cannot let the clutch out like I used too. When letting out the clutch from a dead stop,the rear end now shakes, shutters, and if it is really bad, the rear end starts bouncing. To minimize the shakes, I have to keep the engine below 1000rpm until the clutch/1<sup>st</sup> gear is fully engage. It is worst when there is a load on the truck like going uphill, or a sharp turn for a dead stop. After the truck gets rolling, I don’t notice the problem when shifting gears.
I have been babying it for 7k miles and it has not improved. What is wrong? Did I get a bad clutch job?
GTI 337/20th Anniversary :: Transmission Making Lot Of Chatter Noise?
I heard that smlw flywheel on the 6 speed trannys make a lot of chatter noise, I was cool with that so I put one in with a satch clutch kit and now it sounds like a marble or something is banging around inside!!!
View 3 RepliesGTI 337/20th Anniversary :: 2004 - Noise Coming From Transmission
So there's been a noise coming from what seems like the transmission for some time now.Here is how it began...One day I was reversing and noticed this clatter/grinding/vibrating noise coming from underneath my car. It only happened in reverse.However, now it's happening in all gears but not when accelerating, ONLY on deceleration in gear.
There's no clutch slipping, no noticeable loss in power, etc. Just the noise.I don't want to start replacing things left and right hoping it will fix it so throw-out bearing, trans mount, flywheel, etc?
2004.5 GLI 1.8T O2M. Transmission hasn't been touched from what I know of (bought the car w/ 37k, now has 77K),
Golf IV / Jetta IV :: VR6 5 Speed - Clanking Noise When Letting Clutch Out In Gear
The car runs fine clutch has pressure and everything. I can idle with the clutch pressed down and put into reverse and every gear BUT if I put it in a gear and start to let the clutch out I can hear a clanking or something flying around in there and it doesn't really want to go anywhere and I don't want to really let the clutch all the way out in gear or let it out for too long and screw anything else up worse..
View 2 RepliesGTI 337/20th Anniversary :: Clutch Pedal Would Stick At 3/4 Of The Way Up
I recently got the GTI 1.8L 337 with 64,000 on it. It had been sitting, with daily start-ups, for about 8 months until the ALT was replaced. I've been driving it for a month with no problems until last week. At first I noticed the clutch pedal would pause on the way up for a split second then tap the bottom of my shoe. I thought maybe it needed adjustment but nothing serious. A few days ago the pedal would stick at 3/4 of the way up, and stay there most of the time unless I raised it with my foot, till the car warmed up a bit. Yesterday and today the pedal started to stick 1/4 of the way up, unless raised with my foot, at the morning start-up and will only come up 3/4 when warm. It also wont go into reverse at initial start-up until it gets really warmed up, shifting into other gears is fine. I've had no problems or real sounds shifting into any other gears, though out of 1st has been a little jumpy.
View 3 RepliesGTI 337/20th Anniversary :: Clutch Won't Return - Could Not Put It Into Gear
Today I went to start my car and let it warm up and everything worked fine and it started regularly but when I went to go drive the car and put the clutch in the pedal didn't return and I could not put it into gear, need to identify the problem.
View 4 RepliesGTI 337/20th Anniversary :: 2004 - Clutch Won't Go Into Any Gear
My wife was driving home and was exiting the freeway, downshifted and then no response from the clutch or gearbox. It would move left to right but not go into any gear with the car on. No real pressure in the clutch pedal either. With the car off you are able to find all the gears but when you start the car in gear with the clutch down it just jumps forward and dies. No smoke or burning smells either way and the pedal does come up by itself. Pushed the car into the driveway and its goin to the shop tomorrow morning.
With the search button so far: master/ slave cylinder, full clutch problem, air in brake/clutch lines, shifter linkage bracket
I don't think it's the slave cylinder as the pedal is NOT stuck to the floor, but I am not handy with cars, only motorcycles. First thing I checked was the linkage bracket, which seemed to be fine and as I stated, I was able to get in gear while car was off. Brake fluid was almost full but i know that doesnt rule out air in the lines.
GTI 337/20th Anniversary :: Clutch Pedal Went Soft?
We were headed home the clutch pedal went soft... Ok, I thought it's either the clutch master or slave. I get it home and replace the master and after bleeding I had good pedal feel.
Great I thought, I got lucky and it was only the master. Drive it around for a bit and get on the highway and just as I was about to downshift the pedal went flat to the floor again.
Well after pumping the pedal until it had good feel again I got it home and bleed it a couple more times just to make sure I got all the air out. Drove it again. Same thing, after a little while the pedal gets soft again.
Now before I go and replace the slave is it possible I have a faulty master? Having issues after replacing the master?