Ford Ranger / B-Series :: 1999 - Stalls / Rough Idle And Engine Dies
I have a 1999 B4000 4.0L with 160K miles on it. Bought the truck new. Up until about a year ago it ran perfect but has developed an idle, stalling and occassional jerky ride problem. It occurs at any temperature, engine hot or cold, A/C clutch on or off and in Park, Drive or Neutral. When you start the engine it will not idle unless you keep your foot on the gas. The idle speed will drop to 200-300 rpm and the engine dies. Sometimes you can barely tap the gas pedal and the rpm will shoot up to normal idle speed (about 900 rpm) and stay there a few seconds then begin to drop again. If the engine is cold it will often die a couple times after starting even with the foot on the gas and then about the 2nd or 3rd time run with your foot on the gas.
At stop signs and red lights you have to keep your foot on the gas to keep it running. If you are approaching a stop sign and take your foot off the gas to coast to a stop and brake, the engine rpm will drop and the engine will die. It always starts fine though. Once you are driving it generally runs just fine at low or high speed. You can generally set the cruise control on the expressway and cruise right on. However, sometimes all of a sudden the truck will start bucking and jumping as if it has a terrible misfire. It usually lasts a few seconds and quits. Often if you step on the gas it quits. Even less occasionally the engine will begin to slow as if it is starved for fuel and slow down. You can press the pedal to the floor and it sputters a bit then picks up and runs fine.
I have read about all the threads in this forum and others and tried some of the suggested fixes but it still has the problem. I have tuned it up with new plugs, wires, fuel filter, air filter and PCV valve. Based on some of the forums advice I have replaced the IAC valve, the EGR valve and EGR Pressure Feedback Sensor, and cleaned and inspected the MAF sensor with MAF cleaner. I have checked all my vacuum lines and no leaks there and checked the engine timing which is fine. Fuel rail pressure and engine compression are also fine. Spark plugs show no clues, exhaust is clean and the engine uses virtually no oil. There has been no tear down on the engine like removing the heads, cam, timing gears or any of that and the engine is completely stock.
It shows no codes related to the problem. Two or three months after the problem started I showed a code that indicated an injector problem, traced the problem to a bad injector, replaced the faulty injector and it was fine. That took care of that code but didn't solve the idle problem. In my younger days I was into drag racing and I rebuilt engines, swapped transmissions, etc. and still do my own tune-ups today so I am fairly familiar with auto repair and have most of the tools for testing newer cars but this one stumps me. As a last resort I'm about to take it to the dealer.
Ford Ranger / B-Series :: 2001 Edge Really Rough At Start Up / Stalls On Hard Acceleration
2001 Ranger Edge 3.0. Like the title says, when I start my ranger it idles really rough. If I give it gas it shudders like it's gonna die. After about 2-3 minutes it smooths out. If I'm on the interstate and down shift to pass someone, while accelerating it feels like I have a misfire (no CEL given) not all the time though. I've changed plugs and wires and it stopped doing it so I thought I had it but, it continued a few days later. Then I changed the fuel filter and it stopped again for a few days. Well it's back again. I'm thinking it's the fuel pump but I wanted to check here before I take my truck bed off. I also checked for vac leaks and I'm all good there.
View 1 RepliesFord Ranger / B-Series :: Rough Idle At Start Up - Spark Plug 4 Keeps Going Bad
I'm getting tired of the same problem about every 6 months. Plug #4 keeps going bad. Its been doing this for years. It starts with rough idle when first starting up that clears up quickly then eventually it leads to a misfire when accelerating. Every time this happens I replace plug #4 and its good to go. Just recently (roughly 6 months ago) did a full tune up and all new injectors. About a week or 2 ago it started its rough idle at start up and just the other day it started misfiring again. What would keep causing this??
View 14 RepliesFord Ranger / B-Series :: 1987 - Rough Idle After Start Up / Bogs Down And Wants To Stall
I have an 87 ranger, 2.3 4cyl. 2wd 5 speed. When I start up the truck after it sits for a few hours it will idle fine but then it starts to bog down and wants to stall but after about 5 mins its fine and runs like a champ. I don't know if its a sensor or what.
View 2 RepliesFord Ranger / B-Series :: 1999 - Stalls In Hot Weather / Low Idle Otherwise
I have had my '99 Ranger since 2002. Since it has started getting hot in Texas, the truck has decided to stall at horrible times. When driving on the interstate, there is no problem, but as soon as I get in town and have to let off the gas to turn or stop, the whole truck dies. Unless it sits for a long time, it will continue to die at every stop. It is harder to start each time. I have changed the fuel filter and added STP to the last tank of gas. Also, it is tough to start and keep running until it has warmed up on any day. I have to sit in the truck and keep the idle up so it won't die.
View 1 RepliesFord Ranger / B-Series :: Stumbling And Sometimes Stalls After High Rev Coming Down To Idle
My truck has been doing this since I got it and I can't figure it out. It's a 2000 Ford Ranger XLT 2.5 5Spd. It runs fine if you don't rev it above 2500-3000 rpm. After you rev it that high coming down to idle it is stumbling real bad and sometimes stalls. I've been driving it like this since I got it, and it does fine other than this. It gets better the longer you drive it, but it still will do it if you rev it high enough.
Here are all the parts I personally have changed (previous owner said he did the plugs and wires and air filter, which it looks like he did but I'm about ready to change them myself):
-Fuel filter
-coil packs
-timing belt
-egr valve
-cleaned throttle body
-iacv
-tps
-thermostat
Ford Ranger / B-Series :: 1994 - Idles Rough / Stalls When Cold But Runs Great When Warm
I have a huge problem. My 94 ranger 2.3L 5 speed manual transmission, has problems with idoling while it's cold, has no power going uphill and stalls when I slow down to stop. This is all after putting a new motor in. The old one was running ok with 310,000 but lagging bad. I figured with the driving I do, a new motor wouldn't be a bad thing. Boy, was I wrong. It has been a nightmare. But once the truck is up to operating temperature, it runs so smooth you wouldn't think there was a problem. But let it cool off, restart, and boom! There it is. We have changed so many parts and sensors with absolutely no change to the original problem. It's very frustrating. I just can't let this problem win. I will figure it out.
View 13 RepliesFord Ranger / B-Series :: 1994 - Running Rough At Idle?
Engine runs rough at idle. Two plugs are black and just replaced head gaskets. I installed new short block and new heads six months ago. I can't seem to figure out the problem and I would like to trouble shoot more before tearing heads off and going any further.
View 2 RepliesFord Ranger / B-Series :: 1998 - Rough Idle At Cold?
I understand there is not much adjustable on my 98 Ranger (2.5L) as far as idle speed and mixture. It runs rough when started cold. Is this a sign to replace spark plugs?
View 2 RepliesFord Ranger / B-Series :: 1986 - Start Over Fuel - Idles Very Roughly - Stalls Out?
its 1986 Ranger with a 2.9L V6 Auto 4x4, well to start with it seriously over fueling also it idles very roughly and even stalls out sometimes, when I'm trying to hold it at a speed it acts like it is missing (I guess that's from over fueling as well and it also pukes out lots of black smoke, it goes through way too much gas for a V6), but when I speed up fairly hard it acts fine until I try to maintain speed again, I have already put a tune up into it and a new EGR as well a fuel regulator and how to fix it?
View 14 RepliesFord Ranger / B-Series :: Transmission Start Jerking When Give It Gas / Engine Stalls
I have a 2000 ranger 4.0l 4x4 automatic transmission 5r55e. When I put it in drive I don't have any problems except in do it starts jerking when I give gas. When I put it in reverse I can move but as soon as I give gas it stalls the engine tranny was sitting in another truck swapped it with mine I changed the filter and 5 1/2 quart of oil.
I when to a transmission shop plugged it inn no codes and he said he would changes all solenoid and valve body gasket but he's not sure what is the problem. So I started to take out valve body and notice the oil is darkish red and was wondering if it was normal or not and if I'm taking that valve body out for nothing or should still go ahead ...
Ford Ranger / B-Series :: 2003 V6 Rough Idle / No Power On Highway
168K, to date, replaced
rear 2 cat's
Timing chain and gears
cam sync assem.
Plugs, wires, dis block,
Why.............. Read on
This 2003 ranger 3.0 v6, run very hard at idle, yet it runs and you can drive it around town, ""at"" low rpm, and no hills but it gets from point a to point b
I have no pre ingintion, but a plug that was only 60 days only was burnt out completely on 3rd cyl. bank 1 or as ford call it #3, i am telling you this thing seem like it running on 4 cyl,s kicking back and forth, and replacing everything above made no difference.
On the highway, as long as it is flat or down hill 75-80 mph, as soon as a hill or power to pass is needed it bogs down and slows it self to about 45 mph, I have been though everything i can think of and my next move to to start pulling heads, but i wanted to ask here first.
Ford Ranger / B-Series :: 2002 XLT - Rough Idle - Misfire On Cylinder 3
I have a 2002 ford ranger xlt 3.0 i just rebuilt the entire motor about a month ago and was having a high idle problem for the longest time. turns out i had the iac on backwards. but now that it idles down around where its supposed to it has a rough idle has a little shake to it. starts up right away but when i drive down the road around 3000-3500 rpms its missing on cylinder #3 from what the code I am getting "multiple cylinder misfire, #3 cylinder misfire" I've replaced plugs and wires. camshaft pos sensor. I am getting 65 lbs of fuel pressure. spark on all cylinders. I am really at a dead end here. Also every time I take the plugs out to look at them they look brand new.
View 14 RepliesFord Ranger / B-Series :: 2001 - Rough At Idle / Misfire In Cylinder 1
So I have a 2001 ranger 2.3l . Runs very rough at idle.code says misfire in cyl.#1. I have changed plugs, wires, coil packs all motocraft. I did a compression test..
#1.170
#2 180
#3. 185
#4 . 180
Compression seems fine,but where do i go from here? Anything else i can check/replace to solve this?
Ford Ranger / B-Series :: 1999 - Rough And High Idle At 850 RPMs
1999 B3000 with a 3.0. The truck idles at 850rpms. When it starts it idles at around 1000 and runs very rough. When I disconnect the IAC the engine dies. The AC also has problems it blows cold at idle but at highway speeds after 7-8 minutes running the compressor kicks out. One can turn it off and it blows cold again after a few minutes.
View 5 RepliesFord Ranger / B-Series :: 2007 - Rough Idle At Low RPM Either In Park Or Drive
2007 Ranger 4.0l, idles rough at low rpm, in park or drive, with or without the AC on.
View 1 RepliesFord Ranger / B-Series :: 1995 - Rough Idle And RPMs Drops?
1995 ford ranger with 4.0. It idles rough. Replaced MAF TPS fuel pump fuel filter fuel pressure regulator upper o2 sensor. IAC.. still idles rough RPMs drop. It isn't as bad since replacing MAF but still not right. What else is there.. Cleaned out the air intake port it was gummed up. Don't know what else to do?
View 3 RepliesFord Ranger / B-Series :: 2002 - Rough Idle Codes / Cylinder 2 And 3 Misfiring
I have an 02 ranger xlt 3.0, it started having a rough idle, codes say cylinder #2&3 misfiring, changed plugs, wires, coil pack, didn't work, still same code, checked injectors on right side, all 3 had ohm reading of 15.8-16.5, the injectors were clicking like they are supposed to, sprayed carb cleaner around the intake ports, didn't change the idle at all,what else can I check or do? with out tearing the engine apart, unless of course I have to, the truck has been very good to me, it's got 205,000 miles on it, I need it to last at least another year...
View 4 RepliesFord Ranger / B-Series :: 2004 - Rough Idle - CEL With P0303 And P0316 Codes?
I love my Ranger. I'm quite impressed with the power and durability. I'm ticked at Ford for stopping production.
I have searched my problem and could not quite narrow it down. I have also tried several remedies with no improvement. I need to narrow it down to a specific item.
2004 Ranger, 4.0 liter, 4x4, 131,000 miles, runs great above idle.
Problem: rough idle, idles at about 750 rpm's. If i raise the rpm's to 850 and up, smooth as silk.
The truck did this a few years back. Not quite as rough and it went away by itself.
Engine light came on this time with P0303 & P0316 codes. I have replaced: plugs, wires, coil pack. I know that the #3 plug is sparking quite well. the #3 injector is getting signal to spray not sure if it is. I have 4 O2 sensors and I believe I tested them correctly (passed). The passenger side upstream or pre cat sensor has not been tested yet. Had to rent a tool and will do that in morning. I slid a piece of aluminum roof flashing between the crank position sensor and the crank pulley. Not a noticeable difference. While at idle (750 rpm's) I pulled each (#3,2,1,) (one at a time) injector wire plugs off the injectors. No noticeable difference. I pulled the vacuum line off the egg and operated it with a vacuum tool. Seems to be working fine. Sprayed carb cleaner around on vac lines. No engine surge