Ford Ranger / B-Series :: 1986 - Stalls / Idles Or Runs Roughly And Will Miss Erratically
I have a really nice 1986 Ranger XLT with a 2.9 V6 (injected) and OD Automatic with about 135k miles. I've had the truck for over ten years and have been pretty happy with it. I'm still trying to correct a couple of nuisance items:
1. Sometimes it runs smoothly, and at others it has a rough idle, and once in a while it will even stall. Before it stalls, it idles or runs roughly, and will miss erratically. When it quits, it does not fade out like it is running low on gas; it quits suddenly, like the ignition is turned off. If I am driving at highway speeds, sometimes it will buck as it misses, and sometimes stalls out. But it always starts up right away afterwards. This does not happen often, but when it does, it happens several times over hours or days, and then goes away by itself for months, even years, and then comes back for another round.
I was hoping whatever was wrong would totally fail, but it has been several years and is not getting better, nor worse. Fuel mileage varies, too, from 16 to high 20's MPG. I have new low- and high-pressure fuel pumps (dual tanks), new gas and air filters, checked all the electrical connections, put in a new ignition switch, new O2 sensor, Air Flow sensor, EGR, replaced all the vacuum lines, new battery and cables, new starter, all new electrical relays, fuel pressure regulators, new fuel pump inertia switch, tuned up engine (incl. wires, cap, rotor, ign module, plugs and timing), and cleaned out the already sparkling-clean tanks.
2. My oil pressure will drop at idle to low-normal when the engine is warm. It never goes to below Normal on the gauge. I have replaced the gauge, sending unit, and oil pump. This is a long-term issue, and is not getting any better or worse.
Ford Ranger / B-Series :: Runs Rough For About A Minute After Engine Started When Cold
This has been an ongoing issue for about a month. When I start the engine after it has been sitting and is cold it runs ruff for about a minute then smooths out and runs fine. I pulled a P0304 code (cyl.4 missfire) but I do not get a CEL.
I checked the plugs and they were ok but I changed them and the wires anyway as it just turned 50k and the plugs were original. I could live with a little cold ruff idle but the code throwing bothers me. The truck is a 2000 xlt 4x with auto trans. and 4.0 engine. This is my second 4.0 ranger but I have only had it for about 6 months.
Volvo - V70 :: 2001/ 24T Vehicle Runs Smooth When Cold / Runs Rough With Delayed Acceleration On Warm Up
My 2001 V70 24T runs smooth when cold as it warms up it runs rough with delayed acceleration reaction ....
View 1 RepliesFord Ranger / B-Series :: Runs Rough - Driver Side Exhaust Manifold Cold / Passenger Side Hot?
1990 Bronco II, 2.9l, auto, 4x4. Was running just fine. Sitting in Park just idling away. All of a sudden, just starts running real rough, ticking, etc.
Towed it home. This morning, started up OK but still running really rough.
While running, pulled spark plug wires one at a time from the drivers side. Had no effect but could tell the wires were sparking as I held them up to metal.
Turned truck off. Drivers side exhaust manifold COLD, passenger side HOT.
This sounds real bad to me. Am I missing something simple that could cause the drivers side of the engine to not work?
Ford F-150 (2004-2008) :: Runs Rough And Idles Poorly Only When Cold
I recently replaced the plugs cuz I had a rough idle all the time. During plug change when I discovered they had already been changed I found one that had a burned off electrode. Does this mean a lean condition exists?
After plug change it runs smoothly but only after 10 min warmup in our canadian winters. I can drive it when its not warm but seems to have less than full power and idles very badly after driving w/o proper warmup.
Next I changed fuel filter and checked fpdm, it was a little rusty but not bad so i just mounted it 1/4 off steel to prevent further rusting.
Since then I have installed a programmer [diablosport] but found no codes since i had battery disconnected for filter change. no new codes in last few weeks since.
So do I have a lean running cylinder causing this poor cold idle or a rich cylinder? It must be a clogged or dripping fuel injector right?
Ford Ranger / B-Series :: 2003 4.0L Idles Fine But Stalls When Given Gas
I'm having a bit of trouble with my fathers '03 Ranger Edge 4.0L. It has about 100k miles on it, and we keep it very well maintained. This is the first major problem we've had with it.
When the problem first occured, it had been driven about 30 miles on the highway and about 5 miles after getting off the highway, he pulled up to an intersection and stopped. As he started accelerating again, it all of a sudden started sputtering, surging (almost exactly as if it were running out of gas), and then stalled. It continues to exhibit this behavior. It will start and idle fine, but struggle and then stall when given any amount of throttle. It's also an automatic transmission if that makes any difference.
Fast forward to this past week after we had it towed home. We have checked the fuel pressure, and its dead on at about 64psi. We changed the fuel filter, changed the PCV valve, changed the upstream O2 sensor, put in a new air filter, cleaned the MAF sensor, and cleaned the intake of the throttle body. We're now at a loss as to what could be causing the problem. The CEL is not on, and there are no codes being shown when we plugged it in. We also thought it may have been bad gas, so we drained the tank and put fresh gas in from our preferred station. The plugs and wires are also fairly new, only about 4k miles on them.
Are we missing anything here? What else we could try? The absolute last resort is taking it to a shop, we're going through a rough patch with finances.
Ford Ranger / B-Series :: 1986 - Start Over Fuel - Idles Very Roughly - Stalls Out?
its 1986 Ranger with a 2.9L V6 Auto 4x4, well to start with it seriously over fueling also it idles very roughly and even stalls out sometimes, when I'm trying to hold it at a speed it acts like it is missing (I guess that's from over fueling as well and it also pukes out lots of black smoke, it goes through way too much gas for a V6), but when I speed up fairly hard it acts fine until I try to maintain speed again, I have already put a tune up into it and a new EGR as well a fuel regulator and how to fix it?
View 14 RepliesOldsmobile - Leaks - Cutlassciera :: 1994 V6 Idles Rough And Usually Stalls If Put It In Gear When Start The Engine
I have a 94 Oldsmobile Cutlass Ciera, (3.1L V6 GM3100 engine). When I start the engine it idles very rough and usually stalls if I put it in gear. Eventually once it warms up I can drive it, but when I do drive it's extremely sluggish on accelerations and acts like its about to die. At constant speeds it runs mostly ok. We figured it was a vacuum leak, but we've tried every test we can think of to find it and talked to a couple mechanics and tried their tests and it passed all of them. Supposing it isn't a vacuum leak, then what it might be?
View 4 RepliesFord Ranger / B-Series :: 1994 - Won't Start After Warm Up?
I have a 1994 Ford Ranger 4.0L 4x4, 130,000. I love this truck but about a year ago it started not starting after it warmed up short distances in the summertime? It start right up on cold crank...Runs smooth idles like a champ...but if i shut it off..wont start for 20 to 40 min??? It doesn't happen in the winter months??? So I changed the fuel pump, filter, relays. I feel like it has something to do with the Ignition Control Module. Would that come up in a code?
View 13 RepliesFord Ranger / B-Series :: 1994 - Only Goes In Reverse When Warm?
I have a 1994 Ford Ranger XLT xcab with a 4.0 engine.It will take off and drive in the freezing cold but when it warms up it will only go in reverse.Once in awhile it will go into drive.What seems to be the problem. I had also backed up over a railroad tie in an icy parking lot but still drove away.
View 3 RepliesFord Ranger / B-Series :: 1994 V6 Idles Low - Surges Up / Down - Black Smoke Puffs And Smells Like Gas
I have a 1994 Ford Ranger with 4.0 V6 Automatic. The problem is when it idles it idles low and surges up/down and pushes a very small amount of black smoke puffs and smells like gas. I have installed new coil, new wires, new plugs, new ect, new crankshaft position sensor, and new maf. It has new intake manifold, new injectors, new alternator and it still does the exact same thing. Nothing is phasing it. I ran the key on/engine off test and got egr codes and a map sensor code, then ran the engine running test and got 998 and 126 code. The 998 code says that its basically a hard fault/ have no idea.
I do know this is a donor engine out of another year not sure what year, but i know when i ordered the coolant temp sensor the only ones that would plug into it are the years 1990-1993. Now here's my other question, why would the computer give me a map sensor code when truck doesn't have a map sensor? It has MAF sensor, and why egr codes? The truck doesn't have egr and never came with it. I do know I've unhooked battery and replaced the maf and its like it doesn't even recognize it? Could it be the ecm/computer bad or needs flashed?
Ford Fuel System :: 1989 F250 5.8L Runs Great Then Dies After Warm
I just purchased a 1989 F250 with a 5.8 motor. Great truck for its age. Ive owned other Ford trucks in the past and my Dad had them as a kid. Love them.
When I bought the truck from the 2nd owner it had a problem so I bought this truck with the problem figuring with my past knowledge I could fix it. Not the case. When I got the truck it would start fine and run really great but when it got warm it seems it would die and I would have to wait till it was cooled down to start back up and again it would run fine. Well the problem got worse and worse and now it wont run at all.
It will run on starter fluid so that leads me immediately to the fuel pumps. I say that plural because none of them will run it seems. I did a fuel pressure test at the shrader valve at the top of the motor on the fuel rail and I get no pressure at all when I turn the key. The relay in the engine compartment seems to be working to as I can hear it. I put a new on of those on to to be sure. Leads me back to the pumps again. I replaced the external pump on the fuel rail and I know thats working. I replaced the fuel filter to while I was there.
Is it possible to have BOTH fuel pumps in the front and rear tanks go at once? Seems unusual. My other F150 with dual tanks worked great and when the back tank pump went I could just switch it over to the front tank.
LS / MKZ :: 2002 Lincoln Idles Rough On Cold Mornings But Runs Fine
The car idles rough on cold mornings but runs fine. It will stall while idling but starts back easily. I am getting a 1131 and a 1151 code with my scanner along with 0300 and lean bank 1 codes. I started having these problems after I had to remove the upper intake to replace coil packs. I was getting egr code and had an egr port completely block off but cleaned that out and no longer get the egr codes. Spraying carb cleaner around the engine I get a very slight bump in rpm around a couple of the intake ports could that be my problem or should I look deeper?
View 5 RepliesFord Ranger / B-Series :: 1989 V6 Stalls / Dies / Powerless After Warm Up
I've recently acquired a 1989 ford ranger xlt 2.9L V6 and iv got my elbows deep already..... starts right up and scene its an older truck i let it warm up for a few minutes seems to sound alright so i jump in and take off... well i make it about two blocks and as soon as the truck seems to warm up it starts to sputter and die out... starts back up and idles for a min and i try to take off, but it seems to have NO power and jerks and dies.... so i push to a street parking spot and get situalated start the truck up again and take off only to make it about half a block tell it does the same....
First i think iv run outta gas witch i might of not sure so I walk to station and get three gallons. put in truck and same is happening. so i start kicking myself for not haven any tools with me and i leave tell next day... that night do a little research and get some idea's of what could be the problem'(s) so i start out with things that look like they need tending Badly WIRES, PLUGS, ROTOR, CAP, MAP SENSOR, and now after a whole day in the rain (Northwest BTW) and grease to elbows? 2.9 V6? What step's should i take next?
Ford Ranger / B-Series :: 2008 - Runs Rough With No Power
I just changed the plugs and wires on my 2008 Ranger 3L. Now it runs rough with no power. It was fine before I did the work but I thought I should change the plugs at 215000KM. I used Ford wires but unfortunately I used Bosh platinum plugs and now think I will change to Ford plugs. Do you think the Bosch plugs would be that bad for the Ranger? What is the belt tensioner torx size? I had to move the A/C compressor over to get the #4 plug but had a very hard time trying to loosen the belt.
View 7 RepliesFord Ranger / B-Series :: 2003 Truck Idles A Little Rough - Code P1450
Where to start looking to resolve this code. It is not an intermittent code. It returns after about 3 to 4 key turns. Truck idles a little rough but runs fine. I have looked up the code and causes but wondering how to deal with this directly and fixed it. I'm wanting to sell my truck for something bigger and would like to solve the issue before hand. 2003 Ford Ranger Edge...
View 4 RepliesFord Ranger / B-Series :: 1986 - Starts And Runs Rough / Bad Misfire
My pops has a 86 ranger with a 2.9. And what its been doing is, it will start up just fine then u give it a minute and itll start to run very rough like a bad miss fire, then if he revs it up for a bit. It will clear out and then run just fine until he starts it up again and it seems to do it more the colder it gets and it smells very rich. Iv checked the injectors and there fine, what other things could it be ? O2 sensors oorrr
View 5 RepliesFord Ranger / B-Series :: 1999 - Rough Idles When Started / Have To Hold The Gas Till It Warms Up
Quick back story I bought a 1999 Ford Ranger It is a 4 cyl with an auto trans the guy said it had some trouble with the tranny (major understatement) he also forgot to mention he cut out the CAT. so running a 4 banger off the header.
When you start the truck it rough idles but you have to hold the gas down til it warms up. You can shift into reverse but it labors the motor and the motor will not up the rpms kinda stays at idle and wants to die no matter how hard you accelerate and you can't move up a slight incline.
When you shift into drive you have to rev the motor to 3 grand an it will catch then move slowly forward. no matter how high the revs go. The fluid levels are a tad above the full level and a bit dark for my liking.
Ok, I used an OBDII scan tool from the parts store and it came up with 3 codes P0351, P0352, P0500. From my internet search the first two seem to be coil related which explains why the motor is running like garbage. The last may or may not have to do with what the tranny is doing.
Ford Ranger / B-Series :: 1994 - Running Rough At Idle?
Engine runs rough at idle. Two plugs are black and just replaced head gaskets. I installed new short block and new heads six months ago. I can't seem to figure out the problem and I would like to trouble shoot more before tearing heads off and going any further.
View 2 Replies