Ford Ranger / B-Series :: Easy Start / Rough Low Idle And Stalls
My 2005 2.3l Ranger ran great. I moved a trailer about 150 feet and stalled the truck backing it up. Stick shift. Unhooked the trailer and pulled back into the parking area....all the sudden the truck has extremely rough idle and stalls. It runs good on the highway. AutoZone ran a OEM number to cross: P0171.
I cleaned the IAC with intake cleaner. No Luck
I unhooked battery for 15 min. No Luck
I sprayed intake with 1/2 can of intake cleaner. No Luck
I did not have a tamper torx to remove the MAF. What next.
Ford Ranger / B-Series :: 2001 Edge 4.0 5 Speed Auto - Noise While Accelerating
MY 2001 Edge 4.0 5 speed auto has a noise while accelerating. It happens only when truck is first run and disappears after warming up after a few miles. It just turned 1500 miles. Can't figure out if it is from trans or possibly a speedo cable. It goes to the dealer next week.
View 6 RepliesFord Ranger / B-Series :: 2002 Edge 4.0 Won't Start / Turns Over For A Second But Won't Fire Up
One month ago. I am at a store and it won't start. Turns over for a second but wont fire up. Waited a while and it finally did. Took to auto parts place and we went over all that it might be. I checked the button on the passenger side and it was down as it should be. I replaced fuel fuse 48 in the box under hood. All was well for a week
3 weeks ago again wont start but this time it will turn over and over and over. Waited again and it cranked. Went back to auto place dude said maybe the ground to the computer. So I put a neg ground on it to the frame. Worked for a few days.
1 week ago Again cranks but wont fire. I take it to the ford house expecting expensive sex. They kept it for 2 days and it cranked all the time. They told me it had to not start so they could get a code. Check engine light has never come on. Even when it wont crank. I got truck and went to eat. And yes then it wont crank. Waited and had another marg and it finally cranked but you could smell gas like it was flooded. Took it home.
Today I took it down to auto place and tested fuel pressure. 60 psi no problems. grrrrrrr well maybe it ain't fuel pump. I have to have a truck I can rely on. I have football playoffs coming up and I travel a lot. It has a brand new interstate battery. I put Lucas gas treatment in tank. Dude at auto place said it would clear fuel line and lube fuel pump? It was 10 bucks for big bottle so I figured it couldn't hurt.
If its 10 at night and I am at a game shooting THEN Im sure it wont start.
Ford Ranger / B-Series :: 2003 - Stalls / Shutters On Acceleration
My 2003 ranger, 4.0l, 5 spd manual with 295K miles has no power on acceleration. Engine shutters/stalls. The following have been replaced in last 20k miles; fuel pump, plugs/wires, mass flow sensor and fuel filter. Last week left for work and could not go faster than 50 mph. Condition has gotten worse (barely goes past 40 mph).
Changed filter with no improvement.
Checked fuel pressure - constant at 65 psi.
Changed coil - no change.
The tank of gas I put in just before problem was from station with tanker dumping while I pumped. That tank is out of truck; filled from different station. Also put can of seafoam in tank. No change.
Ford Ranger / B-Series :: 1999 - Stalls / Rough Idle And Engine Dies
I have a 1999 B4000 4.0L with 160K miles on it. Bought the truck new. Up until about a year ago it ran perfect but has developed an idle, stalling and occassional jerky ride problem. It occurs at any temperature, engine hot or cold, A/C clutch on or off and in Park, Drive or Neutral. When you start the engine it will not idle unless you keep your foot on the gas. The idle speed will drop to 200-300 rpm and the engine dies. Sometimes you can barely tap the gas pedal and the rpm will shoot up to normal idle speed (about 900 rpm) and stay there a few seconds then begin to drop again. If the engine is cold it will often die a couple times after starting even with the foot on the gas and then about the 2nd or 3rd time run with your foot on the gas.
At stop signs and red lights you have to keep your foot on the gas to keep it running. If you are approaching a stop sign and take your foot off the gas to coast to a stop and brake, the engine rpm will drop and the engine will die. It always starts fine though. Once you are driving it generally runs just fine at low or high speed. You can generally set the cruise control on the expressway and cruise right on. However, sometimes all of a sudden the truck will start bucking and jumping as if it has a terrible misfire. It usually lasts a few seconds and quits. Often if you step on the gas it quits. Even less occasionally the engine will begin to slow as if it is starved for fuel and slow down. You can press the pedal to the floor and it sputters a bit then picks up and runs fine.
I have read about all the threads in this forum and others and tried some of the suggested fixes but it still has the problem. I have tuned it up with new plugs, wires, fuel filter, air filter and PCV valve. Based on some of the forums advice I have replaced the IAC valve, the EGR valve and EGR Pressure Feedback Sensor, and cleaned and inspected the MAF sensor with MAF cleaner. I have checked all my vacuum lines and no leaks there and checked the engine timing which is fine. Fuel rail pressure and engine compression are also fine. Spark plugs show no clues, exhaust is clean and the engine uses virtually no oil. There has been no tear down on the engine like removing the heads, cam, timing gears or any of that and the engine is completely stock.
It shows no codes related to the problem. Two or three months after the problem started I showed a code that indicated an injector problem, traced the problem to a bad injector, replaced the faulty injector and it was fine. That took care of that code but didn't solve the idle problem. In my younger days I was into drag racing and I rebuilt engines, swapped transmissions, etc. and still do my own tune-ups today so I am fairly familiar with auto repair and have most of the tools for testing newer cars but this one stumps me. As a last resort I'm about to take it to the dealer.
Ford Ranger / B-Series :: 2001 - CEL On / Low RPM And Stalls
My Ranger has been acting funny lately. My check engine light is on. I stopped by an Autozone and the guy read the codes - I don't remember exactly what the code was but he said I just needed to use some fuel cleaner - he recommended Seafoam. Now, I assume he was just trying to sell me something. But I've tried that, Gumout and STP in the tank with no luck.
If I'm driving and come to a stop, my RPM dips down to about 600 or lower, my truck starts shaking and will eventually stall if I don't step on the gas. This only happens with a warm engine - If I start the car up and go a mile down the road, it won't happens. But if I go 10 miles down the road, it will. I assumed I had a bad throttle position sensor so I just ordered the part and replaced it but the same behavior exists.
It's been a while since I've replaced the fuel filter - it might just be that.
Ford Ranger / B-Series :: 1994 - Idles Rough / Stalls When Cold But Runs Great When Warm
I have a huge problem. My 94 ranger 2.3L 5 speed manual transmission, has problems with idoling while it's cold, has no power going uphill and stalls when I slow down to stop. This is all after putting a new motor in. The old one was running ok with 310,000 but lagging bad. I figured with the driving I do, a new motor wouldn't be a bad thing. Boy, was I wrong. It has been a nightmare. But once the truck is up to operating temperature, it runs so smooth you wouldn't think there was a problem. But let it cool off, restart, and boom! There it is. We have changed so many parts and sensors with absolutely no change to the original problem. It's very frustrating. I just can't let this problem win. I will figure it out.
View 13 RepliesFord Ranger / B-Series :: Odd Sound When Taking Off From A Dead Stop Under Hard Acceleration
Wonder if its dry driveshaft slip splines? Only happens when leaving a dead stop under hard acceleration. Hard to describe sound, but seems to be coming from behind me, almost sounds like 2 broken pieces of steel snapping past each other. frame is o.k., leaf springs are o.k. , doesn't do it when shifting between gears or if I gently take off from a stop. I don't think there's a grease fitting for the driveshaft where the splines are (where the 2 piece shaft takes up slack for being loaded or unloaded) may have to take that apart once the weather breaks and see what i find. my 1st ranger never had this issue after 200K miles. this truck is now at 145K but its almost 20 years old. I've read somewhere before about pulling the shaft apart & greasing the splines up. does this sound like a possibility for whats happening? not sure what else it could be.
View 3 RepliesFord Ranger / B-Series :: 2004 - Hard Starting / Rough Idling / No RPMs
backed out of the garage fine later in the day went to put it away started hard would not idle and only rev to 2500 .cleaned map sensor,egg valve tested and it works.cleaned the IAC and that works ,fuel pressure is 58psi. starts hard it would idle now it doesn't dies, no code . with 58psi could the pump still be bad? it has 18 pounds of vacuum. where is the vacuum line for the fuel pressure regulator on the motor?
View 14 RepliesFord Ranger / B-Series :: 2006 XLT - Vibrating Hard / Rough Idling - CEL Is On Solid And Not Flashing
I have a 2006 Ranger XLT 3.0 that is vibrating hard/rough idling, cel is on (solid, not flashing), has trouble accelerating with pedal punched. Will sometimes get a sudden burst when pedal is punched with rpms going up but most of the time no to slow raise of rpms with pedal engaged. Hooked code reader up to it and read ignition coil. Replaced the coil and changed plugs and wires. Truck still not running right. what gives? Is this a fuel pump, cats clogged, cylinder issue?
View 4 RepliesFord Ranger / B-Series :: 1986 - Start Over Fuel - Idles Very Roughly - Stalls Out?
its 1986 Ranger with a 2.9L V6 Auto 4x4, well to start with it seriously over fueling also it idles very roughly and even stalls out sometimes, when I'm trying to hold it at a speed it acts like it is missing (I guess that's from over fueling as well and it also pukes out lots of black smoke, it goes through way too much gas for a V6), but when I speed up fairly hard it acts fine until I try to maintain speed again, I have already put a tune up into it and a new EGR as well a fuel regulator and how to fix it?
View 14 RepliesFord Ranger / B-Series :: Transmission Start Jerking When Give It Gas / Engine Stalls
I have a 2000 ranger 4.0l 4x4 automatic transmission 5r55e. When I put it in drive I don't have any problems except in do it starts jerking when I give gas. When I put it in reverse I can move but as soon as I give gas it stalls the engine tranny was sitting in another truck swapped it with mine I changed the filter and 5 1/2 quart of oil.
I when to a transmission shop plugged it inn no codes and he said he would changes all solenoid and valve body gasket but he's not sure what is the problem. So I started to take out valve body and notice the oil is darkish red and was wondering if it was normal or not and if I'm taking that valve body out for nothing or should still go ahead ...
Ford Ranger / B-Series :: 1997 - Rough Idle At Startup / When Rev Up Chugs Real Hard Then Dies
I am currently working on a 97 ranger with a 4cyl and 5 speed. its having some idle issues that i cant seem to pin point, you can start it and it will idle rough then when you rev it up it chugs real hard then dies. used my scan tool and all the sensors are good, fuel pressure is good, good compression, all 8 plugs are firing good and no codes. The other deal that has me a little confused is when I unhook the hose that runs from the air intake tube to the valve cover, I get a lot of vacuum at that port on the valve cover that the hose hooks to. Also when I plug it and pull the dipstick, I get vacuum at the dipstick tube. never seen this before but at the same time I've only messed with very few of these trucks so I don't know whats normal.
View 6 RepliesFord Ranger / B-Series :: 2001 - Rough Shifting Going From 2 To 3 And 3 To 4
I have a 2001 Ranger edge edition with extended cab, 3.0L engine, auto tranny (I believe it is a 5R55E) with 95000 miles. I am currently having some rough shift problems going from 2 to 3 and 3 to 4. I had the transmission fluid exchanged and it solved the issue a little bit but it hasn't gone away. It seems to rev up a little then shift real rough. I have read hundreds of threads that talk about the Valve body gasket blowing out on these trucks so I was wondering if this description matches that fix (The OD light does not flash when this happens).
I had to have the PCM replaced right after I bought it to get the emissions to pass (codes wouldn't set) and in the process cleaned all my ABS sensors, replaced my Speed sensor on the rear differential and replaced both rotors.Are there some home diagnostics I can do to narrow down my search for the problem? Also, on a different note, my father has an 03 with the 4.0L SOHC in it and it seems to get a heck of a lot more get up and go. I understand it is a larger better engine but what I am experiencing seems very sluggish for any V6. Could they be related? Might it just be a fuel filter?
Ford 6.0L Power Stroke Diesel :: 2005 / E350 Van - Rough Idle Stalls / Hard To Start
Rough idle I have had for little bit.Would stall out at idle or a stop, but fire right up? No one could figure it out with the stalling, but now its bad, started yesterday. Have white/blueish smoke sometimes, ( white smoke smells fuel) on restart after warmed when it dies, first time it took 25 mins to restart, now only takes 5 to 15 mins, when I step on it INCREDIBLE full power, fuel mileage gone to hell also since yesterday. Had full tank, now 1/2 tank.
No problems on cold start at all, no check light, 325,000 and never had this before.
Bad fuel?
ICP?
FICM?
Recent work, new turbo, ( turbo was original turbo installed when built) cooling line to waterpump, oil change, new fuel filters, front brakes and 2 new batteries.
Ford Ranger / B-Series :: 1992 - Hard Start Almost Every Time
I'm working on a 1992 ranger with the 2.3l. Hard start almost every time, sometimes have to hold throttle open sometimes not. Won't start at all this morning. When it does finally start it takes a while for it to start firing on the intake side plugs. Haven't had time to check fuel pressure yet but can hear pump cycle when key is switched on.
View 8 RepliesFord Ranger / B-Series :: 2001 - Rough At Idle / Misfire In Cylinder 1
So I have a 2001 ranger 2.3l . Runs very rough at idle.code says misfire in cyl.#1. I have changed plugs, wires, coil packs all motocraft. I did a compression test..
#1.170
#2 180
#3. 185
#4 . 180
Compression seems fine,but where do i go from here? Anything else i can check/replace to solve this?
Ford Ranger / B-Series :: 1990 Truck Won't / Hard Start When Cold
My 1990 4.0 refuses to start when the air temperature outside is at approx 40 degrees or below. It will crank until the battery runs dead if I let it. At approx 50 degrees farenheit the truck takes forever to start and always backfires out of the tailpipe and intake manifold (blowing off a hose on the vacuum tree) before it starts. If I can get it to backfire, it will start eventually. If it does not backfire, then I can run the battery dead and the truck still refuses to start. This condition has grown from a little problem to a huge problem over the past 6 months. Here is what I have done so far, including regular maintenance items.......
KOEO test checked OK
KOER test returned code 77 multiple times (TPS).
Replaced Throttle pos. sensor
Replace Idle air bypass valve
Subsequent KOER test came back with no more codes except 11 - OK
Load tested battery
Made new heavy gauge battery cables for + and -
New plugs, wires
newer starter
Changed coil pack for known good one off my explorer
Visually inspected hoses for vacuum leaks, replaced 1 cracked hose
1990 Ranger ext cab 4X2 4.0L, K&N air filter in stock airbox, Pacesetter headers, single 2 1/2" exhaust, stock cat no muffler, 260K on truck, 104K on good used engine from my 1994 Explorer. Purchased Ranger brand new in 1990. A4LD w/ shift kit.
Ford Ranger / B-Series :: 1994 - Hard To Start - CEL On - Power Loss
1994 Ranger .. Last wednesday I had to get a jump because the lights where left on. Everything was normal on thursday. Friday morning. I went to go start the truck and notice that it would try once to start and then try a second time and it would start. Today I was driving it. The check engine light came on and when I get the RPMs up to shift up, I would loose all power and have to wait till it gets down below 10mph before I would get the power back.
View 8 Replies